Min Shi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Min Shi has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Jing Sun
Technical Research Center Guizhou Material Industrial Technology Institute Guiyang China
3 shared publications Anrong Huang
Guizhou Material Industrial Technology Institute, Guiyang, Guizhou, China
2 shared publicationsShanshan Luo
Guizhou Material Industrial Technology Institute, Guiyang, Guizhou, China
2 shared publicationsWei Cai Peng
China Ship Development and Design Center
2 shared publications- Zhi Xiong Huang
Wuhan University of Technology
2 shared publications - Anrong Huang
Technical Research Center Guizhou Material Industrial Technology Institute Guiyang China
1 shared publication
Latest Publications
- 10 October 2021
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 36 (3) , 1175-1186
Effect of chain extender on morphologies and properties of PBAT/PLA composites
Biodegradable poly(butylene adipate-co-terephthalate)/poly(lactic acid) (PBAT/PLA) composites were prepared by melt blending, and chain extender was used to improve the compatibility of PBAT/PLA blends through the chemical reaction. The influence of PLA and chain extender contents on mechanical properties, morphology, and rheological properties of PBAT/PLA composites was systematically investigated. The results revealed that the Young’s modulus and stress values gradually increased under the same strain, whereas the elongation at break decreased with the increase of chain extender content for PBAT/PLA (80/20) composites. Noteworthy, the presence of chain extender improves the interfacial compatibility between PLA and PBAT phases. At the chain extender content of 0.4, 0.6, and 0.8 wt.%, the extensional viscosity of the composites exhibited an increasing trend, whereas an obvious strain-hardening phenomenon emerged in the uniaxial extensional curves.
- 10 October 2021
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 36 (3) , 1175-1186
Effect of chain extender on morphologies and properties of PBAT/PLA composites
Biodegradable poly(butylene adipate-co-terephthalate)/poly(lactic acid) (PBAT/PLA) composites were prepared by melt blending, and chain extender was used to improve the compatibility of PBAT/PLA blends through the chemical reaction. The influence of PLA and chain extender contents on mechanical properties, morphology, and rheological properties of PBAT/PLA composites was systematically investigated. The results revealed that the Young’s modulus and stress values gradually increased under the same strain, whereas the elongation at break decreased with the increase of chain extender content for PBAT/PLA (80/20) composites. Noteworthy, the presence of chain extender improves the interfacial compatibility between PLA and PBAT phases. At the chain extender content of 0.4, 0.6, and 0.8 wt.%, the extensional viscosity of the composites exhibited an increasing trend, whereas an obvious strain-hardening phenomenon emerged in the uniaxial extensional curves.
- 15 July 2020
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 35 (10) , 1576-1588
Effect of stretching speed on morphologies and properties of in situ microfibrillar POE/PLA composites
In situ microfibrillar ethylene–octene copolymer (POE)/poly(lactic acid) (PLA) composites (MFCs) with different phase morphologies were prepared by controlling the stretching speed and maintaining the weight ratio of POE/PLA of 80/20. Four different stretching speeds were employed to study the effect of PLA microfibrillar morphology on tensile, crystalline, and rheological properties of MFCs. Scanning electron microscopic images revealed that the morphology of PLA phase was strongly influenced by stretching speed. MFCs with highest aspect ratio and smaller diameter of PLA microfibrils were obtained with a stretching speed of 60 rpm. The PLA microfibrils with high aspect ratio had the best reinforcement effect on MFCs. The dynamic rheological properties indicated that the MFCs achieved higher storage modulus and loss modulus at the stretching speed of 60 rpm.
- 15 July 2020
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 35 (10) , 1576-1588
Effect of stretching speed on morphologies and properties of in situ microfibrillar POE/PLA composites
In situ microfibrillar ethylene–octene copolymer (POE)/poly(lactic acid) (PLA) composites (MFCs) with different phase morphologies were prepared by controlling the stretching speed and maintaining the weight ratio of POE/PLA of 80/20. Four different stretching speeds were employed to study the effect of PLA microfibrillar morphology on tensile, crystalline, and rheological properties of MFCs. Scanning electron microscopic images revealed that the morphology of PLA phase was strongly influenced by stretching speed. MFCs with highest aspect ratio and smaller diameter of PLA microfibrils were obtained with a stretching speed of 60 rpm. The PLA microfibrils with high aspect ratio had the best reinforcement effect on MFCs. The dynamic rheological properties indicated that the MFCs achieved higher storage modulus and loss modulus at the stretching speed of 60 rpm.
- 9 July 2018
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 32 (8) , 1068-1077
Enhanced properties of the poly(propylene carbonate)/poly(butylene succinate) composites with chain extender
Poly(propylene carbonate) (PPC) blended with poly(butylene succinate) (PBS) with chain extender (CE) was prepared by melt mixing. Mechanical properties of PPC/PBS composites showed that the addition of CE can increase its tensile strength and unnotched impact strength, and the PPC/PBS composites had higher tensile strength when CE (0.4 wt%) was added into PPC/PBS composites. Thermogravimetric measurements revealed that adding CE to PPC/PBS (70/30 wt%) can improve the thermal decomposition temperatures ( T −5% and T −10%). Dynamic mechanical analysis revealed that the incorporation of CE increased the storage modulus of the PPC/PBS (70/30 wt%) composites.
- 9 July 2018
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 32 (8) , 1068-1077
Enhanced properties of the poly(propylene carbonate)/poly(butylene succinate) composites with chain extender
Poly(propylene carbonate) (PPC) blended with poly(butylene succinate) (PBS) with chain extender (CE) was prepared by melt mixing. Mechanical properties of PPC/PBS composites showed that the addition of CE can increase its tensile strength and unnotched impact strength, and the PPC/PBS composites had higher tensile strength when CE (0.4 wt%) was added into PPC/PBS composites. Thermogravimetric measurements revealed that adding CE to PPC/PBS (70/30 wt%) can improve the thermal decomposition temperatures ( T −5% and T −10%). Dynamic mechanical analysis revealed that the incorporation of CE increased the storage modulus of the PPC/PBS (70/30 wt%) composites.
- 8 March 2018
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 32 (7) , 922-935
Morphology, crystallization, and thermal and mechanical properties of dynamic vulcanization EPDM/PP thermoplastic elastomer
Dynamically vulcanized thermoplastic olefin based on polypropylene (PP)/ethylene–propylene–diene (EPDM) with different dicumyl peroxide (DCP) content was prepared by twin-screw extruder. The effect of DCP content on gel content, crystallinity, and morphological, thermal, and mechanical properties of dynamically vulcanized EPDM/PP blends with different DCP content was investigated. The scanning electron microscopy was performed to evaluate the structure, as well as to characterize the morphology formed during dynamic vulcanization. The regular cross-linked EPDM particle uniformly distributed in PP matrix when the DCP content was from 0.3% to 0.9%. The crystallization behavior analysis indicated that the cross-linked EPDM promoted the nucleation process of PP, but with increase in DCP content, the percentage of crystallinity of the dynamically vulcanized EPDM/PP blends decreased due to the PP degradation. The tensile strength and elongation at break first increase and then decrease with increase in DCP content. When the DCP content was 0.9%, the tensile strength and elongation at break of dynamically vulcanized EPDM/PP blends were the largest. The gel content of dynamically vulcanized EPDM/PP blends first increased and then decreased with increasing DCP content. When the DCP content was 1.2%, the gel content of dynamically vulcanized EPDM/PP blends was maximum. The proper content range of DCP was from 0.6% to 1.2%.
- 8 March 2018
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 32 (7) , 922-935
Morphology, crystallization, and thermal and mechanical properties of dynamic vulcanization EPDM/PP thermoplastic elastomer
Dynamically vulcanized thermoplastic olefin based on polypropylene (PP)/ethylene–propylene–diene (EPDM) with different dicumyl peroxide (DCP) content was prepared by twin-screw extruder. The effect of DCP content on gel content, crystallinity, and morphological, thermal, and mechanical properties of dynamically vulcanized EPDM/PP blends with different DCP content was investigated. The scanning electron microscopy was performed to evaluate the structure, as well as to characterize the morphology formed during dynamic vulcanization. The regular cross-linked EPDM particle uniformly distributed in PP matrix when the DCP content was from 0.3% to 0.9%. The crystallization behavior analysis indicated that the cross-linked EPDM promoted the nucleation process of PP, but with increase in DCP content, the percentage of crystallinity of the dynamically vulcanized EPDM/PP blends decreased due to the PP degradation. The tensile strength and elongation at break first increase and then decrease with increase in DCP content. When the DCP content was 0.9%, the tensile strength and elongation at break of dynamically vulcanized EPDM/PP blends were the largest. The gel content of dynamically vulcanized EPDM/PP blends first increased and then decreased with increasing DCP content. When the DCP content was 1.2%, the gel content of dynamically vulcanized EPDM/PP blends was maximum. The proper content range of DCP was from 0.6% to 1.2%.
- 2 February 2018
- Published by Wiley in Journal of the Chinese Chemical Society
- Vol. 65 (6) , 681-686
Magnetic Solid Base Catalyst Fe3O4@Gly Used as Acid‐Resistant Catalyst for Biodiesel Production
Fe3O4@Gly nanoparticles were synthetized by coprecipitation and studied in the transesterification of soybean oil and methanol to determine its performance for biodiesel synthesis. The magnetism and catalytic performance of Fe3O4@Gly alkaline catalyst were investigated in detail. With a catalyst dosage 1.5 wt %, methanol/soybean oil ratio of 15:1, reaction temperature of 65 °C, and a reaction time of 3 h, the highest yield of biodiesel was 95.8%. The strong base catalyst CaO was used as comparison, from which it was seen that Fe3O4@Gly was more hydrophobic than the former. Moreover, because of the complete dissolution of oleic acid in methanol, Fe3O4@Gly could make better contact with oleic acid, which made it perform far better than pure CaO in oleic acid. In addition, after four times recycling, the yield of biodiesel was still 86.6%. The results show that Fe3O4@Gly possesses excellent properties of acid resistance and recyclability. The catalyst can be a high‐efficiency alkaline heterogeneous catalyst for biodiesel production.
- 2 February 2018
- Published by Wiley in Journal of the Chinese Chemical Society
- Vol. 65 (6) , 681-686
Magnetic Solid Base Catalyst Fe3O4@Gly Used as Acid‐Resistant Catalyst for Biodiesel Production
Fe3O4@Gly nanoparticles were synthetized by coprecipitation and studied in the transesterification of soybean oil and methanol to determine its performance for biodiesel synthesis. The magnetism and catalytic performance of Fe3O4@Gly alkaline catalyst were investigated in detail. With a catalyst dosage 1.5 wt %, methanol/soybean oil ratio of 15:1, reaction temperature of 65 °C, and a reaction time of 3 h, the highest yield of biodiesel was 95.8%. The strong base catalyst CaO was used as comparison, from which it was seen that Fe3O4@Gly was more hydrophobic than the former. Moreover, because of the complete dissolution of oleic acid in methanol, Fe3O4@Gly could make better contact with oleic acid, which made it perform far better than pure CaO in oleic acid. In addition, after four times recycling, the yield of biodiesel was still 86.6%. The results show that Fe3O4@Gly possesses excellent properties of acid resistance and recyclability. The catalyst can be a high‐efficiency alkaline heterogeneous catalyst for biodiesel production.
- 1 September 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1030-1032, 161-164
Research of UV Curing PUA/EP Damping Coating
In this experiment, we examine the impact of photoinitiator and reactive diluents for the UV curing of epoxy resin and Urethane acrylate in detail, so as to provide a theoretical basis for obtaining a satisfactory light curing system. We conducted a number of UV curing experiments, discussed the key influencing factors of the success in Synthesis experiment, explored and researched the Reaction mechanism to some certain extent. The performance was tested after curing, according to the orthogonal experiment method, we analyses the effect of different factors.
- 1 September 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1030-1032, 161-164
Research of UV Curing PUA/EP Damping Coating
In this experiment, we examine the impact of photoinitiator and reactive diluents for the UV curing of epoxy resin and Urethane acrylate in detail, so as to provide a theoretical basis for obtaining a satisfactory light curing system. We conducted a number of UV curing experiments, discussed the key influencing factors of the success in Synthesis experiment, explored and researched the Reaction mechanism to some certain extent. The performance was tested after curing, according to the orthogonal experiment method, we analyses the effect of different factors.
- 1 September 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1030-1032, 1513-1516
Research of the Piezoelectric Composite Active Control
Instantaneous signal and alternating signals are as driven signals, using PID control, change control coefficient P's size, The stopping time of impact force under instantaneous signal with the piezoelectric ceramic content increases, the stopping time is reduced; after applying active control, the stopping is shorter than that is not applied. After applying the alternating signal to force the cantilever beam, the driving effect of the ceramic sheet is located in a cantilever position A, B, C, the effect of C under controlling is at best. The effect of two driven ceramic sheets is better than that of three driven ceramic sheets, the best control position is B+C.
- 1 September 2014
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1030-1032, 1513-1516
Research of the Piezoelectric Composite Active Control
Instantaneous signal and alternating signals are as driven signals, using PID control, change control coefficient P's size, The stopping time of impact force under instantaneous signal with the piezoelectric ceramic content increases, the stopping time is reduced; after applying active control, the stopping is shorter than that is not applied. After applying the alternating signal to force the cantilever beam, the driving effect of the ceramic sheet is located in a cantilever position A, B, C, the effect of C under controlling is at best. The effect of two driven ceramic sheets is better than that of three driven ceramic sheets, the best control position is B+C.