Rongjing Hong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rongjing Hong has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Hua Wang
3 shared publications- Cheng Lu
School of Mechanical, Materials, Mechatronic and Biomedical Engineering, University of Wollongong, Wollongong, NSW 2522, Australia
2 shared publications Chenggang Fang
Nanjing University of Technology, 210009, China
1 shared publicationPeiyu He
1 shared publication- Peiyu He
School of Mechanical Engineering, Nantong Institute of Technology, Nantong 226001, China
1 shared publication Xiaodiao Huang
Nanjing University of Technology, 210009, China
1 shared publication
Latest Publications
- 1 June 2018
- Published by Elsevier in International Journal of Fatigue
- Vol. 111, 233-242
Fatigue life analysis of slewing bearings in wind turbines
- 1 June 2018
- Published by Elsevier in International Journal of Fatigue
- Vol. 111, 233-242
Fatigue life analysis of slewing bearings in wind turbines
- 21 May 2018
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 233 (5) , 1734-1749
Pitch bearing/raceway fretting: Influence of contact angle
In this paper, a three-dimensional numerical simulation (using ABAQUS) of the radial and tangential wear between a ball bearing and a raceway is presented. The aim was to study the influence of the contact angle between ball and raceway on the fretting. A range of contact angles was studied with critical parameters such as contact stress, relative slip, plastic deformation, and contact state. The model was validated against experimental data. The results show that with an increase in the contact angle, the area of maximum stress increases, the bearing capacity of the raceway decreases, and the maximum radial stress moves from the sub-surface to the raceway surface. The raceway surface is shown to be prone to peeling and wear, which reduces the service life of the raceway.
- 21 May 2018
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 233 (5) , 1734-1749
Pitch bearing/raceway fretting: Influence of contact angle
In this paper, a three-dimensional numerical simulation (using ABAQUS) of the radial and tangential wear between a ball bearing and a raceway is presented. The aim was to study the influence of the contact angle between ball and raceway on the fretting. A range of contact angles was studied with critical parameters such as contact stress, relative slip, plastic deformation, and contact state. The model was validated against experimental data. The results show that with an increase in the contact angle, the area of maximum stress increases, the bearing capacity of the raceway decreases, and the maximum radial stress moves from the sub-surface to the raceway surface. The raceway surface is shown to be prone to peeling and wear, which reduces the service life of the raceway.
- 1 January 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 8829-8833
Force control strategy and test research of underwater dexterous hand
The contract force between the fingertip and object need to be controlled when the underwater dexterous hand grasp the object. The original impedance control method lacks robustness because of the inaccurate dynamic model, position error and unknown stiffness of the object, thus, the position-based neural network impedance control method was studied. The effect of position error was analyzed, the neural network was adopted to compensate the uncertainty of finger dynamics, object position and stiffness one by one, and compensation strategy was deduced in detail. Compensator adopted forward feedback neural network with three layers, and updating rules was obtained based on BP arithmetic and Delta learning rule. Finally, the tests of single finger force control were carried out to verify the compensation effect in these three conditions. The results show that the position-based neural network impedance control is a robust method, and this method is fit to the control system of the underwater dexterous hand.
- 1 January 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 8829-8833
Force control strategy and test research of underwater dexterous hand
The contract force between the fingertip and object need to be controlled when the underwater dexterous hand grasp the object. The original impedance control method lacks robustness because of the inaccurate dynamic model, position error and unknown stiffness of the object, thus, the position-based neural network impedance control method was studied. The effect of position error was analyzed, the neural network was adopted to compensate the uncertainty of finger dynamics, object position and stiffness one by one, and compensation strategy was deduced in detail. Compensator adopted forward feedback neural network with three layers, and updating rules was obtained based on BP arithmetic and Delta learning rule. Finally, the tests of single finger force control were carried out to verify the compensation effect in these three conditions. The results show that the position-based neural network impedance control is a robust method, and this method is fit to the control system of the underwater dexterous hand.