Sumit Balguvhar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Sumit Balguvhar has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Suresh Bhalla
Civil Engineering Department, Indian Institute of Technology Delhi
3 shared publications Suresh Bhalla
Indian Institute of Technology Delhi (India)
2 shared publications- Aleena V. Krishnanunni
Department of Civil Engineering, Indian Institute of Technology (IIT) Delhi, New Delhi 110 016, India
1 shared publication Ankush Jain
Smart Sensors Area, CSIR-Central Electronics Engineering Research Institute, Pilani, Rajasthan, 333031
1 shared publicationDevika Kataria
Institute of Engineering & Technology, J.K. Lakshmipat University, Ajmer Road, Jaipur, Rajasthan, 302026
1 shared publication- Naveet Kaur
Bridge Engineering and Structures Division (BES) Division, CSIR-Central Road Research Institute (CRRI), New Delhi, India
1 shared publication
Latest Publications
- 2 February 2023
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 115 (2) , 169-182
Assessment of mosfet/diode based rectifier interface circuits for piezoelectric energy harvesting from structural vibrations
- 2 February 2023
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 115 (2) , 169-182
Assessment of mosfet/diode based rectifier interface circuits for piezoelectric energy harvesting from structural vibrations
- Open Access
- 30 January 2023
- Published by Elsevier in Energy Reports
- Vol. 9, 2506-2524
Efficacy of singly curved thin piezo transducers for structural health monitoring and energy harvesting for RC structures
- 30 January 2023
- Published by Elsevier in Energy Reports
- Vol. 9, 2506-2524
Open AccessEfficacy of singly curved thin piezo transducers for structural health monitoring and energy harvesting for RC structures
- 18 March 2019
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10973, 28
Feasibility of piezoelectric energy harvesting from real-life city flyover: a case study
The applications of wireless sensor nodes (WSNs) are rapidly growing in civil infrastructures, yet constrained by batteries with the short lifespan. Providing an alternative power source will undoubtedly expand the application for WSNs and other technologies such as energy harvesting. This paper presents a basic field study conducted on a city flyover to explore the possibility of piezoelectric energy harvesting from bridge vibrations. A piezoelectric energy harvester based on Micro Fiber Composite (MFC) has fabricated. The maximum voltage and average power generated by stainless steel PEH with surface bonded MFC patch was found to be 1.34 V and 0.784 μW respectively. Finally, the practical application of energy harvested achieved by lighting an LED with vibration energy.
- 18 March 2019
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10973, 28
Feasibility of piezoelectric energy harvesting from real-life city flyover: a case study
The applications of wireless sensor nodes (WSNs) are rapidly growing in civil infrastructures, yet constrained by batteries with the short lifespan. Providing an alternative power source will undoubtedly expand the application for WSNs and other technologies such as energy harvesting. This paper presents a basic field study conducted on a city flyover to explore the possibility of piezoelectric energy harvesting from bridge vibrations. A piezoelectric energy harvester based on Micro Fiber Composite (MFC) has fabricated. The maximum voltage and average power generated by stainless steel PEH with surface bonded MFC patch was found to be 1.34 V and 0.784 μW respectively. Finally, the practical application of energy harvested achieved by lighting an LED with vibration energy.
Evaluation of power extraction circuits on piezo‐transducers operating under low‐frequency vibration‐induced strains in bridges
The concept of piezoelectric energy harvesting (PEH) provides a promising solution for perpetually running low‐power electronic devices such as wireless sensor networks by harvesting ambient vibrations generated from civil structures such as long span bridges, city flyovers, elevated metro corridors, which are constantly under dynamic loads. However, its successful industrial‐scale deployment on civil structures is still not realised because of the low‐frequency of vibrations (typically 31 mode, which is the most natural mode of excitation, has not been investigated in depth for piezo‐patches directly bonded on the main structure. Studies, which have focused on electronic conditioning circuitry, have been restricted to typically high‐voltage and high‐frequency scenarios only. This paper focuses on systematically studying the issues inflicting energy harvesting from the ambient vibrations induced flexural strains civil structures, such as city flyovers, using piezo elements in d31 mode. Vibration measurements are first undertaken from a typical city flyover consisting of steel girders supporting a reinforced concrete (RC) deck. The basic site measurements are employed to perform a laboratory‐based parametric study to investigate the influence of parameters such as vibration frequency, voltage, and circuit components like diodes on PEH. On the basis of the experimental results, it can be concluded that power in microwatts range can be typically harvested from these civil structures through directly bonded piezo patches in d31 mode. However, there are still issues associated with electronic circuitry accompanying harvesters, such as diodes and storage elements. The same are summarised and future directions envisioned.
Evaluation of power extraction circuits on piezo‐transducers operating under low‐frequency vibration‐induced strains in bridges
The concept of piezoelectric energy harvesting (PEH) provides a promising solution for perpetually running low‐power electronic devices such as wireless sensor networks by harvesting ambient vibrations generated from civil structures such as long span bridges, city flyovers, elevated metro corridors, which are constantly under dynamic loads. However, its successful industrial‐scale deployment on civil structures is still not realised because of the low‐frequency of vibrations (typically 31 mode, which is the most natural mode of excitation, has not been investigated in depth for piezo‐patches directly bonded on the main structure. Studies, which have focused on electronic conditioning circuitry, have been restricted to typically high‐voltage and high‐frequency scenarios only. This paper focuses on systematically studying the issues inflicting energy harvesting from the ambient vibrations induced flexural strains civil structures, such as city flyovers, using piezo elements in d31 mode. Vibration measurements are first undertaken from a typical city flyover consisting of steel girders supporting a reinforced concrete (RC) deck. The basic site measurements are employed to perform a laboratory‐based parametric study to investigate the influence of parameters such as vibration frequency, voltage, and circuit components like diodes on PEH. On the basis of the experimental results, it can be concluded that power in microwatts range can be typically harvested from these civil structures through directly bonded piezo patches in d31 mode. However, there are still issues associated with electronic circuitry accompanying harvesters, such as diodes and storage elements. The same are summarised and future directions envisioned.
- 1 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 134-137
Green Energy Harvesting Using Piezoelectric Materials from Bridge Vibrations
Piezoelectric energy harvesting from bridge vibrations has attracted many researchers not because it provides a clean and autonomous solution to power portable electronic devices, in addition, it helps in making a smart city. This paper focuses on energy harvesting from low-frequency bridge vibrations which includes vibrations measurements from a city flyover and laboratory experiment using traditional rectifier circuit at low frequency and small amplitude vibrations for storage. The typical practical issues have been addressed associated with PEH from bridge vibrations and electrical circuitry.
- 1 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 134-137
Green Energy Harvesting Using Piezoelectric Materials from Bridge Vibrations
Piezoelectric energy harvesting from bridge vibrations has attracted many researchers not because it provides a clean and autonomous solution to power portable electronic devices, in addition, it helps in making a smart city. This paper focuses on energy harvesting from low-frequency bridge vibrations which includes vibrations measurements from a city flyover and laboratory experiment using traditional rectifier circuit at low frequency and small amplitude vibrations for storage. The typical practical issues have been addressed associated with PEH from bridge vibrations and electrical circuitry.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 422-426
Realization of MEMS-based silicon cantilever using bulk micromachining
Micro cantilevers are an important component of smart sensors as they detect the stress on surfaces caused by various physical/ chemical or biological parameters. The proper design of the cantilever dimension helps to achieve optimum sensitivity of sensor. This work presents the design simulations of Si cantilever beam using Finite element method. The design is implemented by fabrication of a pair of cantilevers on a single trench. Deep Reactive-Ion Etching (DRIE) was employed to release the Si cantilever from bulk silicon. The released structure was characterized by using Laser Doppler Vibrometer (LDV). The Eigen frequency of the cantilever measured by LDV is found to be similar to the designed specifications. The design and fabrication aspects have been discussed in the paper along with analysis of the Eigen frequency achieved.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 422-426
Realization of MEMS-based silicon cantilever using bulk micromachining
Micro cantilevers are an important component of smart sensors as they detect the stress on surfaces caused by various physical/ chemical or biological parameters. The proper design of the cantilever dimension helps to achieve optimum sensitivity of sensor. This work presents the design simulations of Si cantilever beam using Finite element method. The design is implemented by fabrication of a pair of cantilevers on a single trench. Deep Reactive-Ion Etching (DRIE) was employed to release the Si cantilever from bulk silicon. The released structure was characterized by using Laser Doppler Vibrometer (LDV). The Eigen frequency of the cantilever measured by LDV is found to be similar to the designed specifications. The design and fabrication aspects have been discussed in the paper along with analysis of the Eigen frequency achieved.