Hossein Hassannejad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hossein Hassannejad has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Ashkan Nouri
Department of Metallurgy and Materials Engineering, Faculty of Engineering, Arak University, Arak, Iran
10 shared publications Ashkan Nouri
Department of Metallurgy and Materials Engineering, Faculty of Engineering, Arak University, Arak, Iran
4 shared publicationsMorteza Farrokhi-Rad
Department of Materials Engineering, Faculty of Engineering, Azarbaijan Shahid Madani University, Tabriz, Iran
4 shared publicationsM. Aliofkhazraei
3 shared publications- Taghi Shahrabi
Department of Materials Engineering, Faculty of Engineering, Tarbiat Modares University, P.O. Box: 14115-143, Tehran, Iran
3 shared publications - Benedetto Bozzini
Department of Energy, Politecnico di Milano, Via Lambruschini 4, 20156 Milano, Italy
2 shared publications
Latest Publications
- 21 April 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 31 (11) , 8906-8913
Novel Approach for the Synthesis of Highly Corrosion Resistant and Electrically Conductive Cerium Hexaboride Coating
- 21 April 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 31 (11) , 8906-8913
Novel Approach for the Synthesis of Highly Corrosion Resistant and Electrically Conductive Cerium Hexaboride Coating
- 26 July 2021
- Published by SAGE Publications in Surface Engineering
- Vol. 37 (9) , 1176-1185
Electrophoretic deposition of alginate coatings from different alcohol-water mixtures
Alginate coatings were fabricated by electrophoretic deposition (EPD) using alcohol (methanol, ethanol and isopropanol)-water mixtures at different ratios. Water electrolysis and so current density increased with water content and EPD time leading to the more bubbles in coatings. EPD rate increased with water amount due to the increase in concentration of H+ and Alg− ions and reduction in solution viscosity. According to the results of kinetics, optical microscopy and corrosion analyses the coating deposited at 10 V for 1 min from the ethanolic solution with 60 vol.-% of water was selected as the optimum coating for in-vitro cell culture and antibacterial analyses. There was almost 30% rise in cell expansion for the sample with optimum coating after 7 days compared to the blank. Also, the coated sample showed antibacterial activity against Bacillus bacteria.
- 26 July 2021
- Published by SAGE Publications in Surface Engineering
- Vol. 37 (9) , 1176-1185
Electrophoretic deposition of alginate coatings from different alcohol-water mixtures
Alginate coatings were fabricated by electrophoretic deposition (EPD) using alcohol (methanol, ethanol and isopropanol)-water mixtures at different ratios. Water electrolysis and so current density increased with water content and EPD time leading to the more bubbles in coatings. EPD rate increased with water amount due to the increase in concentration of H+ and Alg− ions and reduction in solution viscosity. According to the results of kinetics, optical microscopy and corrosion analyses the coating deposited at 10 V for 1 min from the ethanolic solution with 60 vol.-% of water was selected as the optimum coating for in-vitro cell culture and antibacterial analyses. There was almost 30% rise in cell expansion for the sample with optimum coating after 7 days compared to the blank. Also, the coated sample showed antibacterial activity against Bacillus bacteria.
- 26 October 2020
- Published by Springer Nature in Metals and Materials International
- Vol. 28 (3) , 646-656
In Situ Formation of Extremely High Corrosion Resistant Ni–Ni3Si Nanocomposite Coating Using Spark Plasma Sintering and Subsequent Heat Treatment
- 26 October 2020
- Published by Springer Nature in Metals and Materials International
- Vol. 28 (3) , 646-656
In Situ Formation of Extremely High Corrosion Resistant Ni–Ni3Si Nanocomposite Coating Using Spark Plasma Sintering and Subsequent Heat Treatment
- 15 June 2020
- Published by SAGE Publications in Surface Engineering
- Vol. 37 (2) , 236-245
Corrosion and mechanical behaviour of biodegradable PLA-cellulose nanocomposite coating on AZ31 magnesium alloy
In this study, the effect of cellulose nanoparticles (CNs) on the corrosion and mechanical behaviour of the biodegradable polylactic acid (PLA) coating was investigated. For this purpose, 1, 5, and 10 wt-% of CNs were added to the PLA coating. By adding CNs to the coating, the corrosion resistance of the PLA coating increased and the highest improvement in corrosion resistance was obtained at 5 wt-% of CNs. Further increase of CNs from 5 to 10 wt-% reduces the corrosion resistance of the PLA coating due to a decrease in the adhesion of the coating to the substrate from 2.4 to 1.6 MNm−2. Also, the presence of CNs gives higher hardness and better mechanical properties.
- 15 June 2020
- Published by SAGE Publications in Surface Engineering
- Vol. 37 (2) , 236-245
Corrosion and mechanical behaviour of biodegradable PLA-cellulose nanocomposite coating on AZ31 magnesium alloy
In this study, the effect of cellulose nanoparticles (CNs) on the corrosion and mechanical behaviour of the biodegradable polylactic acid (PLA) coating was investigated. For this purpose, 1, 5, and 10 wt-% of CNs were added to the PLA coating. By adding CNs to the coating, the corrosion resistance of the PLA coating increased and the highest improvement in corrosion resistance was obtained at 5 wt-% of CNs. Further increase of CNs from 5 to 10 wt-% reduces the corrosion resistance of the PLA coating due to a decrease in the adhesion of the coating to the substrate from 2.4 to 1.6 MNm−2. Also, the presence of CNs gives higher hardness and better mechanical properties.
- 1 January 2020
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 770
The bake hardening mechanism of dual-phase silicon steels under high pre-strain
- 1 January 2020
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 770
The bake hardening mechanism of dual-phase silicon steels under high pre-strain
- 22 August 2019
- Published by Wiley in Steel Research International
- Vol. 90 (11)
Relationship between Microstructure and Corrosion Behavior in Dual‐Phase Steels with Various Si Content
The objective herein is to evaluate the effect of silicon on the corrosion behavior of dual‐phase steels. For this purpose, five different steels with various Si content ranging from 0.34 to 2.26 wt% are intercritically annealed at 780 °C for 15 min. It is clarified that the mechanism of the effect of Si on the corrosion behavior of dual‐phase steels is a mutual mechanism. The increase in Si content (from 0.34% to 0.91%) initially reduces corrosion resistance due to a decrease in the volume fraction of martensite. However, according to microcapillary studies, a further increase in Si content (from 0.91% to 2.26%) reduces the potential difference between ferrite and martensite and, as a result, reduces the galvanic couple between them. Therefore, corrosion resistance improves by increasing Si content in the range of 0.91%–2.26%. It is also shown that in the corroded surface of the low‐silicon sample, γ‐FeOOH is mainly formed, whereas with an increase in Si content, this compound reduces and α‐FeOOH rises. Also, β‐FeOOH, silicon oxide and Fe3O4 are formed in the high‐silicon sample. The study of the corroded surface topography depicts that surface roughness in a high‐Si sample is less than low‐Si sample.
- 22 August 2019
- Published by Wiley in Steel Research International
- Vol. 90 (11)
Relationship between Microstructure and Corrosion Behavior in Dual‐Phase Steels with Various Si Content
The objective herein is to evaluate the effect of silicon on the corrosion behavior of dual‐phase steels. For this purpose, five different steels with various Si content ranging from 0.34 to 2.26 wt% are intercritically annealed at 780 °C for 15 min. It is clarified that the mechanism of the effect of Si on the corrosion behavior of dual‐phase steels is a mutual mechanism. The increase in Si content (from 0.34% to 0.91%) initially reduces corrosion resistance due to a decrease in the volume fraction of martensite. However, according to microcapillary studies, a further increase in Si content (from 0.91% to 2.26%) reduces the potential difference between ferrite and martensite and, as a result, reduces the galvanic couple between them. Therefore, corrosion resistance improves by increasing Si content in the range of 0.91%–2.26%. It is also shown that in the corroded surface of the low‐silicon sample, γ‐FeOOH is mainly formed, whereas with an increase in Si content, this compound reduces and α‐FeOOH rises. Also, β‐FeOOH, silicon oxide and Fe3O4 are formed in the high‐silicon sample. The study of the corroded surface topography depicts that surface roughness in a high‐Si sample is less than low‐Si sample.
- 17 July 2019
- Published by Springer Nature in Carbon Letters
- Vol. 30 (1) , 63-71
In situ fabrication of high-percent Ni–graphene nanocomposite coating
- 17 July 2019
- Published by Springer Nature in Carbon Letters
- Vol. 30 (1) , 63-71
In situ fabrication of high-percent Ni–graphene nanocomposite coating
- 17 May 2019
- Published by Springer Nature in Tribology Letters
- Vol. 67 (3) , 69
Effect of Silicon Content on the Wear Behavior of Low-Carbon Dual-Phase Steels
- 17 May 2019
- Published by Springer Nature in Tribology Letters
- Vol. 67 (3) , 69
Effect of Silicon Content on the Wear Behavior of Low-Carbon Dual-Phase Steels
- 13 February 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (5) , 055312
Study of corrosion behavior of the biodegradable chitosan-polyvinyl alcohol coatings on AA8011 aluminum alloy
- 13 February 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (5) , 055312
Study of corrosion behavior of the biodegradable chitosan-polyvinyl alcohol coatings on AA8011 aluminum alloy