Frédéric Moens
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Frédéric Moens has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Alain Séraudie
Office National d'Etudes et de Recherches Aérospatiales
1 shared publication- Alessandro De Gaspari
Department of Aerospace Science and Technology, Politecnico di Milano, Milan, Italy
1 shared publication Eric Laurendeau
Polytechnique Montreal
1 shared publicationFrancis Micheli
Office National d'Etudes et de Recherches Aérospatiales
1 shared publicationFrédéric Ternoy
ONERA
1 shared publicationHugues Remy
AIRBUS France
1 shared publication
Latest Publications
- 23 December 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 63 (5) , 1-14
Experimental Test Campaign for Stall Characterization on a Generic Variable Sweep Wing
Aircraft wing stall is a highly complex phenomenon as several mechanisms interact depending on global and local flow characteristics. Recent developments in numerical methods and aerodynamic modeling make possible the vision of an accurate prediction of stall in the near future. In order to reach this objective, there is a need for a high-quality experimental database for validation, including surface and flowfield measurements. To that purpose, a generic test model was specifically designed and built to provide force balance metrics as well as steady and unsteady pressure signals. In particular, the model takes into account forward, backward, and zero sweep angles while adding high-lift devices in order to modify the stall mechanism on the wing. The model was then tested at the ONERA-F2 wind tunnel, and experimental results validate the model’s intended stall characteristics and provide the needed flow data for future numerical validations. This paper describes the different design choices, the measurement techniques considered for this test campaign, and the first results obtained validating the stall processes expected for the different designed configurations.
- 23 December 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 63 (5) , 1-14
Experimental Test Campaign for Stall Characterization on a Generic Variable Sweep Wing
Aircraft wing stall is a highly complex phenomenon as several mechanisms interact depending on global and local flow characteristics. Recent developments in numerical methods and aerodynamic modeling make possible the vision of an accurate prediction of stall in the near future. In order to reach this objective, there is a need for a high-quality experimental database for validation, including surface and flowfield measurements. To that purpose, a generic test model was specifically designed and built to provide force balance metrics as well as steady and unsteady pressure signals. In particular, the model takes into account forward, backward, and zero sweep angles while adding high-lift devices in order to modify the stall mechanism on the wing. The model was then tested at the ONERA-F2 wind tunnel, and experimental results validate the model’s intended stall characteristics and provide the needed flow data for future numerical validations. This paper describes the different design choices, the measurement techniques considered for this test campaign, and the first results obtained validating the stall processes expected for the different designed configurations.
- 22 September 2025
- Published by Elsevier in Computers & Fluids
- Vol. 302
ONERA’s CRM WBPN database for machine learning activities, related regression challenge and first results
- 22 September 2025
- Published by Elsevier in Computers & Fluids
- Vol. 302
ONERA’s CRM WBPN database for machine learning activities, related regression challenge and first results
- Open Access
- 27 March 2019
- Published by Wiley in International Journal of Aerospace Engineering
- Vol. 2019, 1-21
Aerodynamic Shape Design and Validation of an Advanced High-Lift Device for a Regional Aircraft with Morphing Droop Nose
In the present work, the aerodynamic shape design of an advanced high-lift system for a natural laminar flow (NLF) wing, based on the combination of a morphing droop nose and a single slot trailing edge flap, is presented. The paper presents both the aerodynamic design and optimization of the NLF wing and the high-lift configuration considering the mutual effects of both flap devices. Concerning the morphing droop nose (DN), after defining the parameterization techniques adopted to describe the geometry in terms of morphing shape and flap settings, the external configuration is obtained by an aerodynamic shape optimization procedure able to meet geometrical constraints and the skin structural requirements due to the morphing. The final performance assessment of the three-dimensional high-lift configurations is performed by high-fidelity aerodynamic analyses. The design procedure is applied to a twin-prop regional aircraft equipped with a natural laminar flow wing. The morphing droop nose is compatible with an NLF wing that requires the continuity of the skin and, at the same time, extends the possibilities to improve the performances of the class of regional aircraft which usually are not equipped with conventional leading edge devices. Additionally, the morphing technology applied to the flap allows the design of a tracking system fully integrated inside the airfoil geometry, leading to a solution without external fairings and so with no extra friction drag penalty for the aircraft.
- 27 March 2019
- Published by Wiley in International Journal of Aerospace Engineering
- Vol. 2019, 1-21
Open AccessAerodynamic Shape Design and Validation of an Advanced High-Lift Device for a Regional Aircraft with Morphing Droop Nose
In the present work, the aerodynamic shape design of an advanced high-lift system for a natural laminar flow (NLF) wing, based on the combination of a morphing droop nose and a single slot trailing edge flap, is presented. The paper presents both the aerodynamic design and optimization of the NLF wing and the high-lift configuration considering the mutual effects of both flap devices. Concerning the morphing droop nose (DN), after defining the parameterization techniques adopted to describe the geometry in terms of morphing shape and flap settings, the external configuration is obtained by an aerodynamic shape optimization procedure able to meet geometrical constraints and the skin structural requirements due to the morphing. The final performance assessment of the three-dimensional high-lift configurations is performed by high-fidelity aerodynamic analyses. The design procedure is applied to a twin-prop regional aircraft equipped with a natural laminar flow wing. The morphing droop nose is compatible with an NLF wing that requires the continuity of the skin and, at the same time, extends the possibilities to improve the performances of the class of regional aircraft which usually are not equipped with conventional leading edge devices. Additionally, the morphing technology applied to the flap allows the design of a tracking system fully integrated inside the airfoil geometry, leading to a solution without external fairings and so with no extra friction drag penalty for the aircraft.