AOAzusa Ooi

Azusa Ooi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Azusa Ooi has a total of 31 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Corrosion Behavior of Carbon Steel under Soil Drying Conditions

    by Azusa Ooi, Eiji Tada

    Understanding the corrosion behavior of steel under realistic environmental conditions is essential for ensuring the durability of buried infrastructures. In this study, the corrosion behavior of carbon steel was investigated during a soil drying process under varying moisture content conditions. Electrochemical impedance spectroscopy combined with time-resolved analysis was used to monitor the temporal change in the corrosion rate, and the results were compared with the oxygen reduction behavior on Pt electrodes and the moisture dynamics evaluated using glassy carbon electrodes. The corrosion rate of carbon steel increased during drying, driven by enhanced oxygen transport through gas-phase pathways formed in the soil, which promoted the cathodic oxygen reduction reaction (ORR). However, the corrosion current remained substantially lower than the ORR-limited current on Pt electrodes. This was probably because of the suppression of anodic dissolution caused by the reduction in the liquid-phase volume near the steel surface, even as cathodic reactions became dominant. As drying further progressed, the NaCl concentration increased and the oxygen solubility decreased, leading to suppression of the ORR. In addition, the continued loss of the electrolyte phase further limited anodic processes, eventually resulting in the complete cessation of corrosion. These findings provide new insights into corrosion mechanisms under non-stationary soil moisture conditions, and they will contribute to more realistic assessment of the long-term performance of buried steel structures.

  • Open Access

    Crack Initiation and Propagation Mechanism of Rapidly Tempered High-Si Steel during Hydrogen Embrittlement

    by Manami Sunako, Masataka Mizumoto, Ren Tanaka, Shintaro Kumai, Yuichiro Yamauchi, Azusa Ooi, Eiji Tada

    In this study, we focused on fine dispersion of Fe2-3C (ε) by combining the addition of Si and rapid tempering to improve the hydrogen embrittlement resistance of high-strength spring steels. The aim of this study is to clarify the fracture mechanism of rapidly tempered high-Si steels: the JISSUP7 (2.0Si) and SAE9254 (1.4Si) spring steels were tempered at different tempering rates by induction (IH) and furnace heating (FH) methods. Bending test were carried out during the cathodic hydrogen charging to observe the fracture origin and morphology of the steels. The size and volume of carbides were quantified using small-angle X-ray scattering method (SAXS) and synchrotron radiation XRD. The distribution of carbides was observed with the replica method: facets were observed at the fracture origin of the 2.0Si-IH steel and 1.4Si-IH steel, which contained retained γ in the microstructure. It was considered that the facets formed because retained γ at the grain boundaries transformed into martensite during hydrogen embrittlement, promoting intergranular cracking; the 2.0Si-IH steel contained the largest amount of retained γ, but also contained fine Fe2-3C(ε) in the lath. This suggests that dislocations and hydrogen are less likely to accumulate at the grain boundaries, resulting in the longest fracture life. In other words, in rapidly tempered high Si steels (2.0Si-IH steels), the fine dispersion of Fe2-3C (ε) has more influence on the suppression of crack initiation and propagation than the increase in the amount of retained γ, and this contributes significantly to the fracture life.

  • Open Access

    Effect of Soil Moisture on Corrosion Behavior of Zinc in Simulated Soil Environment

    by Mizuki Miyauchi, Azusa Ooi, Eiji Tada

    Corrosion of zinc in simulated soil at various degrees of saturation Sr was investigated by performing surface observations, corrosion depth analyses, electrochemical impedance spectroscopy, and potentiodynamic polarization tests. The aim was to evaluate the effects of soil moisture on the corrosion morphology and corrosion rate of zinc. At a high soil moisture content (Sr > 80%), the mean zinc corrosion rate was low and varied little as Sr varied. However, at a low moisture content (Sr < 80%), the mean corrosion rate increased markedly as the moisture content decreased and reached a maximum at Sr ~ 50%. The zinc corrosion morphology became more heterogeneous, indicating that the corrosion depth increased, as Sr decreased. The effects of soil moisture on the zinc corrosion morphology and rate were assessed from changes in oxygen reduction (cathodic reaction) and zinc dissolution (anodic reaction) in simulated soil.


  • Open Access

    Effect of NaCl Concentration on Galvanic Corrosion Behavior of Zinc and A1050 Couples

    by Junho Jang, Azusa Ooi, Eiji Tada

    In this study, effects of NaCl concentration on galvanic corrosion behavior of zinc and A1050 couple was investigated by means of corrosion potential and galvanic current measurements, surface observation, electrochemical impedance measurements, and polarization tests. Corrosion potential and galvanic currents were measured for 72 hours during immersion in 0.01 to 2 mol L−1 NaCl solutions. During the galvanic corrosion tests, the corrosion potential of the couples remained nearly constant, except in the early stage of immersion, and became more negative as the NaCl concentration increased. During the immersion test, the galvanic current always flowed in the direction of the zinc being the anode. However, the galvanic current changed with immersion time. That is, in the early stage of immersion, the galvanic currents were higher at higher NaCl concentrations, but over time, these values decreased, and after 72 hours, they decreased to much lower values and were almost independent of the NaCl concentration. Surface observations, electrochemical impedance measurements, and polarization curve measurements revealed that a decrease in the cathodic reaction rate on the A1050 surface with immersion time. Finally, the corrosion mechanisms that explain the galvanic corrosion of zinc and A1050 were discussed.


  • Open Access

    Hydrogen Embrittlement Properties of Rapid Tempered High-Si Steel and Effects of the Carbide and Retained Austenite on Its Properties

    by Manami Sunako, Masataka Mizumoto, Azusa Ooi, Eiji Tada

    Automotive suspension springs are required to be high-strength and lightweight, and currently have a maximum strength of 2000 MPa. In addition, they must have high resistance to hydrogen embrittlement in the service environment. From previous research, Si addition or rapid tempering improves the hydrogen embrittlement resistance of low alloy steel. In this study, we investigated the hydrogen embrittlement properties of steel samples with different Si contents and tempering rates and the effects of the fine iron carbides and retained austenite on its properties for 2000 MPa suspension spring steel. JISSUP7 (2.0Si) and SAE9254 (1.4Si) spring steels were tempered at different tempering rates by induction (IH) and furnace heating (FH) methods. Four-point bending tests under corrosion cycles were performed on these steels, and the time to failure was measured. The results show that the 2.0Si-IH steel with higher Si content and higher tempering rate has the longest fracture life and highest resistance to hydrogen embrittlement, even with relatively high diffusible hydrogen content. The size and volume fraction of iron carbides and retained austenite were evaluated by TEM, EBSD, and synchrotron XRD, and the 2.0Si-IH steels were found to have the smallest size and the highest volume fraction of fine iron carbides Fe2-3C(ε) and the highest amount of retained austenite. It is considered that the fine iron carbides of Fe2-3C(ε) work as hydrogen trap sites and that their high dispersion suppresses dislocation movement. They suppress hydrogen accumulation in stress concentrated areas and are expected to improve resistance to hydrogen embrittlement.


  • Open Access

    Hydrogen Embrittlement Properties of Rapid Tempered High-Si Steel and Effects of the Carbide and Retained Austenite on Its Properties

    by Manami Sunako, Masataka Mizumoto, Azusa Ooi, Eiji Tada

    Automotive suspension springs are required to be high-strength and lightweight, and currently have a maximum strength of 2000 MPa. In addition, they must have high resistance to hydrogen embrittlement in the service environment. From previous researches, Si addition or rapid tempering improve the hydrogen embrittlement resistance of low alloy steel. In this study, we investigated the hydrogen embrittlement properties of steel samples with different Si contents and tempering rates and the effects of the fine iron carbides and retained austenite on its properties for 2000 MPa suspension spring steel. JISSUP7 (2.0Si) and SAE9254 (1.4Si) spring steels were tempered at different tempering rates by induction (IH) and furnace heating (FH) methods. Four-point bending tests under corrosion cycles were performed on these steels, and the time to failure was measured. The results show that the 2.0Si-IH steel with higher Si content and higher tempering rate has the longest fracture life and highest resistance to hydrogen embrittlement, even with relatively high diffusible hydrogen content. The size and volume fraction of iron carbides and retained austenite were evaluated by TEM, EBSD, and synchrotron XRD, and the 2.0Si-IH steels were found to have the smallest size and the highest volume fraction of fine iron carbides Fe2-3C(e) and the highest amount of retained austenite. It is considered that the fine iron carbides of Fe2-3C(e) work as hydrogen trap sites and that their high dispersion suppresses dislocation movement. They suppress hydrogen accumulation in stress concentrated areas and are expected to improve resistance to hydrogen embrittlement.


  • Effect of Small Amounts of Cr and Mo on Aqueous CO2 and H2S Corrosion of Low-Alloyed Steel

    by Keiichi Kondo, Eiji Tada, Azusa Ooi

    One of the important industrial issues is the corrosion of carbon and low-alloy steels exposed to a wet environment where CO2 and/or H2S are dissolved. In the case of carbon and low-alloy steels, mainly iron-based corrosion products such as iron carbonate and iron sulfides can form depending on the condition. Microalloys added in small amounts to carbon steel can change the water chemistry near the steel surface due to the dissolution of the microalloys, which may also alter the corrosion resistance of the steel and corrosion morphology. In this study, the individual microalloying effects of a small amount (1 mass%) of Cr and Mo added in carbon steel were investigated in a wet CO2 and H2S environment, where the formation of mackinawite (FeS) is considered to be the dominant iron-based corrosion product. The variation of corrosion rate and corrosion potential of the microalloyed steels was monitored in the NaCl solution aerated with CO2—10% H2S gas by linear polarization resistance measurements. The corrosion product formed on the steel surface was also analyzed by scanning electron microscopy, energy dispersive x-ray spectroscopy, x-ray diffraction, transmission electron microscopy, and x-ray photoelectron spectroscopy. The experimental results show that the addition of a small amount of Cr improves corrosion resistance by forming a dense film of FeS on the surface, while the addition of a small amount of Mo delays the formation of FeS on the surface and the corrosion resistance behavior is similar to that of steel with no additions.