Alaine Herrero-Bermello
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Alaine Herrero-Bermello has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- José Manuel Luque-González
Universidad de Málaga
5 shared publications - Pavel Cheben
National Research Council
5 shared publications Aitor V. Velasco
4 shared publications- Aitor V. Velasco
Departamento de Óptica, Facultad de Ciencias Físicas, Universidad Complutense de Madrid, Madrid, Spain
4 shared publications Jens H. Schmid
4 shared publicationsAlejandro Ortega-Moñux
3 shared publications
Latest Publications
- 17 June 2020
- Published by Optica Publishing Group in Optics Letters
- Vol. 45 (13) , 3398-3401
Polarization splitting directional coupler using tilted subwavelength gratings
On-chip polarization splitters are key elements for coherent optical communication systems and polarization diversity circuits. These devices are often implemented with directional couplers that are symmetric for one polarization and strongly asymmetric for the other polarization. To achieve this asymmetry, highly dissimilar waveguides are used in each coupler arm, often requiring additional material layers or etch steps. Here we demonstrate polarization splitting with a directional coupler composed of two fully etched subwavelength waveguides, differing only in the tilt angle of the silicon segments. Our device exhibits deep-UV compatible feature sizes, is 14 µm long, and covers a 72 nm bandwidth with insertion losses below 1 dB and an extinction ratio in excess of 15 dB.
- 17 June 2020
- Published by Optica Publishing Group in Optics Letters
- Vol. 45 (13) , 3398-3401
Polarization splitting directional coupler using tilted subwavelength gratings
On-chip polarization splitters are key elements for coherent optical communication systems and polarization diversity circuits. These devices are often implemented with directional couplers that are symmetric for one polarization and strongly asymmetric for the other polarization. To achieve this asymmetry, highly dissimilar waveguides are used in each coupler arm, often requiring additional material layers or etch steps. Here we demonstrate polarization splitting with a directional coupler composed of two fully etched subwavelength waveguides, differing only in the tilt angle of the silicon segments. Our device exhibits deep-UV compatible feature sizes, is 14 µm long, and covers a 72 nm bandwidth with insertion losses below 1 dB and an extinction ratio in excess of 15 dB.
- 15 May 2020
- Published by Optica Publishing Group in Optics Express
- Vol. 28 (11) , 16385-16393
Experimental demonstration of metamaterial anisotropy engineering for broadband on-chip polarization beam splitting
Subwavelength metamaterials exhibit a strong anisotropy that can be leveraged to implement high-performance polarization handling devices in silicon-on-insulator. Whereas these devices benefit from single-etch step fabrication, many of them require small feature sizes or specialized cladding materials. The anisotropic response of subwavelength metamaterials can be further engineered by tilting its constituent elements away from the optical axis, providing an additional degree of freedom in the design. In this work, we demonstrate this feature through the design, fabrication and experimental characterization of a robust multimode interference polarization beam splitter based on tilted subwavelength gratings. A 110-nm minimum feature size and a standard silicon dioxide cladding are maintained. The resulting device exhibits insertion loss as low as 1 dB, an extinction ratio better than 13 dB in a 120-nm bandwidth, and robust tolerances to fabrication deviations.
- 15 May 2020
- Published by Optica Publishing Group in Optics Express
- Vol. 28 (11) , 16385-16393
Experimental demonstration of metamaterial anisotropy engineering for broadband on-chip polarization beam splitting
Subwavelength metamaterials exhibit a strong anisotropy that can be leveraged to implement high-performance polarization handling devices in silicon-on-insulator. Whereas these devices benefit from single-etch step fabrication, many of them require small feature sizes or specialized cladding materials. The anisotropic response of subwavelength metamaterials can be further engineered by tilting its constituent elements away from the optical axis, providing an additional degree of freedom in the design. In this work, we demonstrate this feature through the design, fabrication and experimental characterization of a robust multimode interference polarization beam splitter based on tilted subwavelength gratings. A 110-nm minimum feature size and a standard silicon dioxide cladding are maintained. The resulting device exhibits insertion loss as low as 1 dB, an extinction ratio better than 13 dB in a 120-nm bandwidth, and robust tolerances to fabrication deviations.
- 28 November 2019
- Published by Optica Publishing Group in Optics Letters
- Vol. 44 (23) , 5840-5843
On-chip Fourier-transform spectrometers and machine learning: a new route to smart photonic sensors
Miniaturized silicon photonics spectrometers capable of detecting specific absorption features have great potential for mass market applications in medicine, environmental monitoring, and hazard detection. However, state-of-the-art silicon spectrometers are limited by fabrication imperfections and environmental conditions, especially temperature variations, since uncontrolled temperature drifts of only 0.1°C distort the retrieved spectrum precluding the detection and classification of the absorption features. Here we present a new strategy that exploits the robustness of machine learning algorithms to signal imperfections, enabling recognition of specific absorption features in a wide range of environmental conditions. We combine on-chip spatial heterodyne Fourier-transform spectrometers and supervised learning to classify different input spectra in the presence of fabrication errors, without temperature stabilization or monitoring. We experimentally show the differentiation of four different input spectra under an uncontrolled 10°C range of temperatures, about $ 100\times $ increase in operational range, with a success rate up to 82.5% using state-of-the-art support vector machines and artificial neural networks.- 28 November 2019
- Published by Optica Publishing Group in Optics Letters
- Vol. 44 (23) , 5840-5843
On-chip Fourier-transform spectrometers and machine learning: a new route to smart photonic sensors
Miniaturized silicon photonics spectrometers capable of detecting specific absorption features have great potential for mass market applications in medicine, environmental monitoring, and hazard detection. However, state-of-the-art silicon spectrometers are limited by fabrication imperfections and environmental conditions, especially temperature variations, since uncontrolled temperature drifts of only 0.1°C distort the retrieved spectrum precluding the detection and classification of the absorption features. Here we present a new strategy that exploits the robustness of machine learning algorithms to signal imperfections, enabling recognition of specific absorption features in a wide range of environmental conditions. We combine on-chip spatial heterodyne Fourier-transform spectrometers and supervised learning to classify different input spectra in the presence of fabrication errors, without temperature stabilization or monitoring. We experimentally show the differentiation of four different input spectra under an uncontrolled 10°C range of temperatures, about $ 100\times $ increase in operational range, with a success rate up to 82.5% using state-of-the-art support vector machines and artificial neural networks.- Open Access
- 25 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 11 (6) , 1-11
Design of an Athermal Interferometer Based on Tailored Subwavelength Metamaterials for On-Chip Microspectrometry
Temperature dependence is one of the main challenges of the silicon-on-insulator platform due to the large thermo-optic coefficient of its core material. In this work we propose a design of an all-passive athermal silicon-on-insulator Mach-Zehnder interferometer (MZI) based on the standard silicon material platform. The MZI's temperature compensation is achieved by optimizing the relative length of the wire and subwavelength grating arms and by tailoring the thermal response of the subwavelength structure. Simulations of the device performance showed that an overall temperature sensitivity of 7.5 pm/K could be achieved over a 100 nm spectral range near the 1550 nm region.
- 25 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 11 (6) , 1-11
Open AccessDesign of an Athermal Interferometer Based on Tailored Subwavelength Metamaterials for On-Chip Microspectrometry
Temperature dependence is one of the main challenges of the silicon-on-insulator platform due to the large thermo-optic coefficient of its core material. In this work we propose a design of an all-passive athermal silicon-on-insulator Mach-Zehnder interferometer (MZI) based on the standard silicon material platform. The MZI's temperature compensation is achieved by optimizing the relative length of the wire and subwavelength grating arms and by tailoring the thermal response of the subwavelength structure. Simulations of the device performance showed that an overall temperature sensitivity of 7.5 pm/K could be achieved over a 100 nm spectral range near the 1550 nm region.
- Open Access
- 23 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 11 (5) , 1-8
Zero-Birefringence Silicon Waveguides Based on Tilted Subwavelength Metamaterials
Polarization independent silicon-on-insulator nanowires are highly sought after, due the inherent high birefringence of this material platform. State-of-the-art designs of non-birefringent waveguides include ridge waveguides and square nanowires, which either imply large dimensions, multiple etching steps, low fabrication tolerances or high wavelength dependence. In this work, we overcome all the aforementioned limitations through tilted subwavelength structures which provide anisotropy control of the resulting metamaterial. With a waveguide cross section of only 300 nm × 550 nm (height × width), the zero-birefringence point is obtained for an approximately 48°-tilt of the subwavelength structure. Birefringence of the nominal design deteriorates by only $9.10^{-3}$ even in the presence of size deviations of ± 10 nm. Moreover, birefringence is maintained under $6.10^{-3}$ in a 100-nm bandwidth around the central wavelength of 1550 nm. This innovative approach is readly adaptable to a wide range of waveguide sizes, while maintaining single-etch-step fabrication.- 23 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 11 (5) , 1-8
Open AccessZero-Birefringence Silicon Waveguides Based on Tilted Subwavelength Metamaterials
Polarization independent silicon-on-insulator nanowires are highly sought after, due the inherent high birefringence of this material platform. State-of-the-art designs of non-birefringent waveguides include ridge waveguides and square nanowires, which either imply large dimensions, multiple etching steps, low fabrication tolerances or high wavelength dependence. In this work, we overcome all the aforementioned limitations through tilted subwavelength structures which provide anisotropy control of the resulting metamaterial. With a waveguide cross section of only 300 nm × 550 nm (height × width), the zero-birefringence point is obtained for an approximately 48°-tilt of the subwavelength structure. Birefringence of the nominal design deteriorates by only $9.10^{-3}$ even in the presence of size deviations of ± 10 nm. Moreover, birefringence is maintained under $6.10^{-3}$ in a 100-nm bandwidth around the central wavelength of 1550 nm. This innovative approach is readly adaptable to a wide range of waveguide sizes, while maintaining single-etch-step fabrication. - Open Access
- 19 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 11 (3) , 1-8
Design of a Broadband Polarization Splitter Based on Anisotropy-Engineered Tilted Subwavelength Gratings
Polarization management is of paramount importance in integrated optics, particularly for highly birefringent photonic platforms such as silicon-on-insulator. In this work, we present a polarization beam splitter based on a multimode interference coupler incorporating tilted subwavelength gratings. The tilt provides accurate control of the structural anisotropy and enables independent selection of the beat length for two orthogonal polarization states. As a result, device length is reduced to less than 100 μm while simultaneously achieving broadband operation through subwavelength grating dispersion engineering. Insertion losses below 1 dB and an extinction ratio higher than 20 dB are demonstrated through 3D FDTD simulation in a 131-nm bandwidth.
- 19 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 11 (3) , 1-8
Open AccessDesign of a Broadband Polarization Splitter Based on Anisotropy-Engineered Tilted Subwavelength Gratings
Polarization management is of paramount importance in integrated optics, particularly for highly birefringent photonic platforms such as silicon-on-insulator. In this work, we present a polarization beam splitter based on a multimode interference coupler incorporating tilted subwavelength gratings. The tilt provides accurate control of the structural anisotropy and enables independent selection of the beat length for two orthogonal polarization states. As a result, device length is reduced to less than 100 μm while simultaneously achieving broadband operation through subwavelength grating dispersion engineering. Insertion losses below 1 dB and an extinction ratio higher than 20 dB are demonstrated through 3D FDTD simulation in a 131-nm bandwidth.
- 21 September 2018
- Published by Optica Publishing Group in Optics Letters
- Vol. 43 (19) , 4691-4694
Tilted subwavelength gratings: controlling anisotropy in metamaterial nanophotonic waveguides
Subwavelength grating (SWG) structures are an essential tool in silicon photonics, enabling the synthesis of metamaterials with a controllable refractive index. Here we propose, for the first time to the best of our knowledge, tilting the grating elements to gain control over the anisotropy of the metamaterial. Rigorous finite difference time domain simulations demonstrate that a 45° tilt results in an effective index variation on the fundamental TE mode of 0.23 refractive index units, whereas the change in the TM mode is 20 times smaller. Our simulation predictions are corroborated by experimental results. We furthermore propose an accurate theoretical model for designing tilted SWG structures based on rotated uniaxial crystals that is functional over a wide wavelength range and for both the fundamental and higher order modes. The proposed control over anisotropy opens promising venues in polarization management devices and transformation optics in silicon photonics.
- 21 September 2018
- Published by Optica Publishing Group in Optics Letters
- Vol. 43 (19) , 4691-4694
Tilted subwavelength gratings: controlling anisotropy in metamaterial nanophotonic waveguides
Subwavelength grating (SWG) structures are an essential tool in silicon photonics, enabling the synthesis of metamaterials with a controllable refractive index. Here we propose, for the first time to the best of our knowledge, tilting the grating elements to gain control over the anisotropy of the metamaterial. Rigorous finite difference time domain simulations demonstrate that a 45° tilt results in an effective index variation on the fundamental TE mode of 0.23 refractive index units, whereas the change in the TM mode is 20 times smaller. Our simulation predictions are corroborated by experimental results. We furthermore propose an accurate theoretical model for designing tilted SWG structures based on rotated uniaxial crystals that is functional over a wide wavelength range and for both the fundamental and higher order modes. The proposed control over anisotropy opens promising venues in polarization management devices and transformation optics in silicon photonics.
- Open Access
- 1 June 2017
- Published by Optica Publishing Group in Optics Letters
- Vol. 42 (11) , 2239-2242
Temperature dependence mitigation in stationary Fourier-transform on-chip spectrometers
We present two techniques for mitigating the effects of temperature drifts in waveguide spatial heterodyne Fourier-transform on-chip spectrometers. In high-resolution devices, large optical path length differences result in an increased sensitivity to temperature variations and impose stringent requirements on the thermal stabilization system. In order to overcome this limitation, here we experimentally demonstrate two new temperature mitigation techniques based on a temperature-sensitive calibration and phase error correction. The spectrometer chip under analysis comprises an array of 32 Mach–Zehnder interferometers fabricated on a silicon-on-insulator platform. The optical path delays are implemented as microphotonic spirals of linearly increasing length up to 3.779 cm, yielding a spectral resolution of 17 pm. We demonstrate that the degradation in retrieved spectra caused by temperature drift is effectively eliminated by temperature-sensitive calibration and phase error correction.
- 1 June 2017
- Published by Optica Publishing Group in Optics Letters
- Vol. 42 (11) , 2239-2242
Open AccessTemperature dependence mitigation in stationary Fourier-transform on-chip spectrometers
We present two techniques for mitigating the effects of temperature drifts in waveguide spatial heterodyne Fourier-transform on-chip spectrometers. In high-resolution devices, large optical path length differences result in an increased sensitivity to temperature variations and impose stringent requirements on the thermal stabilization system. In order to overcome this limitation, here we experimentally demonstrate two new temperature mitigation techniques based on a temperature-sensitive calibration and phase error correction. The spectrometer chip under analysis comprises an array of 32 Mach–Zehnder interferometers fabricated on a silicon-on-insulator platform. The optical path delays are implemented as microphotonic spirals of linearly increasing length up to 3.779 cm, yielding a spectral resolution of 17 pm. We demonstrate that the degradation in retrieved spectra caused by temperature drift is effectively eliminated by temperature-sensitive calibration and phase error correction.