Tesleem B. Asafa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tesleem B. Asafa has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
M. O. Durowoju
Mechanical Engineering Department, Ladoke Akintola University of Technology, Ogbomoso, Nigeria
3 shared publicationsE. R. Sadiku
Tshwane University of Technology, Pretoria, South Africa
2 shared publicationsK. O. Oladosu
Mechanical Engineering Department, Kwara State University, Malete, Nigeria
2 shared publicationsM. B. Shongwe
University of Johannesburg, Johannesburg, South Africa
2 shared publicationsM. T. Ajala
Industrial Maintenance Engineering Department, Yaba College of Technology, Yaba, Nigeria
2 shared publicationsO. S. Ismail
Mechanical Engineering Department, University of Ibadan, Ibadan, Nigeria
2 shared publications
Latest Publications
- Open Access
- 18 December 2025
- Published by Lujosh Ventures Limited in LAUTECH Journal of Engineering and Technology
- Vol. 19 (5) , 21-55
Physico-mechanical properties, tribological behaviour and metallurgical characteristics of aluminium metal matrix composites reinforced with agricultural residues: A Review
Aluminium Metal Matrix Composites (AMMCs) that are reinforced with agricultural residues (such as rice husk ash, coconut shell ash, sugarcane bagasse ash, maize/corn-cob ash, palm kernel and shell ash) have garnered increasing attention as environmentally friendly, low-cost, and lightweight alternatives to traditional ceramic reinforcements. This review gathers recent findings on (1) physico-mechanical properties (tensile strength, hardness, ductility, density), (2) tribological behaviour (wear rate, friction coefficient, wear mechanisms), and (3) metallurgical characteristics (microstructure, interfacial bonding, phase formation, porosity) of agro-reinforced AMMCs. The review describes common synthesis methods (stir casting and powder metallurgy), emphasises critical microstructure–property correlations, pinpoints persistent challenges (particle agglomeration, inadequate wettability, porosity, variable pre-treatment) and optimisation process. Key fabrication techniques are briefly outlined, and future research directions encompassing hybridisation techniques and surface modifications are provided
- 18 December 2025
- Published by Lujosh Ventures Limited in LAUTECH Journal of Engineering and Technology
- Vol. 19 (5) , 21-55
Open AccessPhysico-mechanical properties, tribological behaviour and metallurgical characteristics of aluminium metal matrix composites reinforced with agricultural residues: A Review
Aluminium Metal Matrix Composites (AMMCs) that are reinforced with agricultural residues (such as rice husk ash, coconut shell ash, sugarcane bagasse ash, maize/corn-cob ash, palm kernel and shell ash) have garnered increasing attention as environmentally friendly, low-cost, and lightweight alternatives to traditional ceramic reinforcements. This review gathers recent findings on (1) physico-mechanical properties (tensile strength, hardness, ductility, density), (2) tribological behaviour (wear rate, friction coefficient, wear mechanisms), and (3) metallurgical characteristics (microstructure, interfacial bonding, phase formation, porosity) of agro-reinforced AMMCs. The review describes common synthesis methods (stir casting and powder metallurgy), emphasises critical microstructure–property correlations, pinpoints persistent challenges (particle agglomeration, inadequate wettability, porosity, variable pre-treatment) and optimisation process. Key fabrication techniques are briefly outlined, and future research directions encompassing hybridisation techniques and surface modifications are provided
- Open Access
- 21 December 2023
- Published by Springer Nature in Discover Materials
- Vol. 3 (1) , 1-14
Development of aluminum composite reinforced with selected agricultural residues
The use of agricultural residue has been considered an economic and environmentally friendly approach for development of aluminium composites. In this study, Al powder (Al) was reinforced with coconut shell ash (CSA), rice husk ash (RHA), and cassava peel ash (CPA) for enhanced physicomechanical performance of the resulting composites. Five samples (Ao–Al, A1–Al + 15RHA, A2–Al + 5CSA + 5RHA + 5CPA, A3–Al + 15CPA, and A4–Al + 15RHA) were prepared in a two-step stir-casting technique and characterized based on physical, mechanical and metallurgical properties. Microstructural analysis revealed that all the particles bonded well with the aluminum alloy. The densities of samples A1, A2, A3, and A4 reduced by 4.78%, 7.75%, 11.44%, and 14.76%, respectively compared to the control sample Ao while porosities rose by 2.1%, 2.23%, 2.56%, and 2.98% respectively. Sample A2 has the highest tensile strength (39.84 MPa) and hardness (120 HBR) which denote 33.60% and 64.27% enhancement compared to the unreinforced sample. These observations can be attributed to the presence of intermetallic compounds such as Fe3Si and Al6Fe present in the composites as well as uniformly distributed and strongly bounded reinforcement within the aluminum matrix. The composite made from the combination of the three reinforcements gave the best physicomechanical properties and therefore recommended for engineering applications.
- 21 December 2023
- Published by Springer Nature in Discover Materials
- Vol. 3 (1) , 1-14
Open AccessDevelopment of aluminum composite reinforced with selected agricultural residues
The use of agricultural residue has been considered an economic and environmentally friendly approach for development of aluminium composites. In this study, Al powder (Al) was reinforced with coconut shell ash (CSA), rice husk ash (RHA), and cassava peel ash (CPA) for enhanced physicomechanical performance of the resulting composites. Five samples (Ao–Al, A1–Al + 15RHA, A2–Al + 5CSA + 5RHA + 5CPA, A3–Al + 15CPA, and A4–Al + 15RHA) were prepared in a two-step stir-casting technique and characterized based on physical, mechanical and metallurgical properties. Microstructural analysis revealed that all the particles bonded well with the aluminum alloy. The densities of samples A1, A2, A3, and A4 reduced by 4.78%, 7.75%, 11.44%, and 14.76%, respectively compared to the control sample Ao while porosities rose by 2.1%, 2.23%, 2.56%, and 2.98% respectively. Sample A2 has the highest tensile strength (39.84 MPa) and hardness (120 HBR) which denote 33.60% and 64.27% enhancement compared to the unreinforced sample. These observations can be attributed to the presence of intermetallic compounds such as Fe3Si and Al6Fe present in the composites as well as uniformly distributed and strongly bounded reinforcement within the aluminum matrix. The composite made from the combination of the three reinforcements gave the best physicomechanical properties and therefore recommended for engineering applications.
- Open Access
- 1 February 2023
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 17 (1) , 345-353
Temperature and Die Angular Effect on Tensile Strength, Hardness, Extrusion Load and Flow Stress in Aluminum 6063 Processed by Equal Channel Angular Extrusion Method
Developing aluminum with good mechanical properties like hardness, tensile strength, and normal flow stress, Equal Channel Angular Extrusion (ECAE) method has been suggested as a suitable metal forming process. The load applied and extrusion temperature normally influences the flow stress...
- 1 February 2023
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 17 (1) , 345-353
Open AccessTemperature and Die Angular Effect on Tensile Strength, Hardness, Extrusion Load and Flow Stress in Aluminum 6063 Processed by Equal Channel Angular Extrusion Method
Developing aluminum with good mechanical properties like hardness, tensile strength, and normal flow stress, Equal Channel Angular Extrusion (ECAE) method has been suggested as a suitable metal forming process. The load applied and extrusion temperature normally influences the flow stress...
- 4 April 2021
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 28 (31) , 42596-42608
Artificial neural network prediction of CO emission and ash yield from co-combustion of empty fruit bunch, palm kernel shell and kaolin
The quantity of ash yield and carbon monoxide (CO) emitted during co-combustion of empty fruit bunch (EFB), palm kernel shells (PKS) and kaolin in a grate furnace depend on the fuels mixing ratio, the combustion temperature and duration. These factors can be tuned to minimize ash deposition and CO emission which is partly responsible for the greenhouse effect. In this study, seventy-three (73) data points were obtained from combustion of EFB, PKS and kaolin mixtures based on D-optimal design. Artificial neural network (ANN) model, optimized with Taguchi technique, was developed to predict ash yield (AY) and CO emission from the combustion of the fuel mixture. The data were divided into training, validation and testing in a 2:1:1 relative proportion. The optimized ANN architecture for AY and CO emission were 5-11-3-1 and 5-6-3-1, respectively, with scale conjugate gradient training algorithm and a learning rate of 0.1. Results of the ANN model agreed significantly with the experimental results with coefficients of determination (R2) of 0.96 and 0.93 for ash yield and CO emission, respectively. The mathematical models for the ash and CO emission using the D-optimal design indicate a good fit with R2 of 0.916 and 0.906, respectively. Parametric studies based on the two models showed that ash yield and CO emission reduced with increased combustion temperature and increased fraction of PKS within the temperature range of 800–1000 °C. These results indicated that both ANN and D-optimal can be deployed to select mixture with minimal ash yield and CO emission.
- 4 April 2021
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 28 (31) , 42596-42608
Artificial neural network prediction of CO emission and ash yield from co-combustion of empty fruit bunch, palm kernel shell and kaolin
The quantity of ash yield and carbon monoxide (CO) emitted during co-combustion of empty fruit bunch (EFB), palm kernel shells (PKS) and kaolin in a grate furnace depend on the fuels mixing ratio, the combustion temperature and duration. These factors can be tuned to minimize ash deposition and CO emission which is partly responsible for the greenhouse effect. In this study, seventy-three (73) data points were obtained from combustion of EFB, PKS and kaolin mixtures based on D-optimal design. Artificial neural network (ANN) model, optimized with Taguchi technique, was developed to predict ash yield (AY) and CO emission from the combustion of the fuel mixture. The data were divided into training, validation and testing in a 2:1:1 relative proportion. The optimized ANN architecture for AY and CO emission were 5-11-3-1 and 5-6-3-1, respectively, with scale conjugate gradient training algorithm and a learning rate of 0.1. Results of the ANN model agreed significantly with the experimental results with coefficients of determination (R2) of 0.96 and 0.93 for ash yield and CO emission, respectively. The mathematical models for the ash and CO emission using the D-optimal design indicate a good fit with R2 of 0.916 and 0.906, respectively. Parametric studies based on the two models showed that ash yield and CO emission reduced with increased combustion temperature and increased fraction of PKS within the temperature range of 800–1000 °C. These results indicated that both ANN and D-optimal can be deployed to select mixture with minimal ash yield and CO emission.
- 18 February 2021
- Published by Springer Nature
- p. 21-73
Characterization Techniques in Nanotechnology: The State of the Art
- 18 February 2021
- Published by Springer Nature
- p. 21-73
Characterization Techniques in Nanotechnology: The State of the Art
- 3 February 2021
- Published by Springer Nature in Bulletin of Materials Science
- Vol. 44 (1) , 1-11
Physico-mechanical properties of emulsion paint embedded with silver nanoparticles
- 3 February 2021
- Published by Springer Nature in Bulletin of Materials Science
- Vol. 44 (1) , 1-11
Physico-mechanical properties of emulsion paint embedded with silver nanoparticles
- 6 May 2020
- Published by Springer Nature in SN Applied Sciences
- Vol. 2 (6) , 1-12
Gr–Al composite reinforced with Si3N4 and SiC particles for enhanced microhardness and reduced thermal expansion
- 6 May 2020
- Published by Springer Nature in SN Applied Sciences
- Vol. 2 (6) , 1-12
Gr–Al composite reinforced with Si3N4 and SiC particles for enhanced microhardness and reduced thermal expansion
- Open Access
- 22 February 2020
- Published by Springer Nature in SN Applied Sciences
- Vol. 2 (3) , 1-12
Correlation between theoretical and experimental hardness, elastic modulus of discarded aluminium piston reinforced with zirconium diboride and snail shells
- 22 February 2020
- Published by Springer Nature in SN Applied Sciences
- Vol. 2 (3) , 1-12
Open AccessCorrelation between theoretical and experimental hardness, elastic modulus of discarded aluminium piston reinforced with zirconium diboride and snail shells
- 20 November 2013
- Published by Springer Nature in Applied Physics A
- Vol. 116 (2) , 751-757
Influence of germanium incorporation on the structural and electrical properties of boron-doped ultrathin poly-Si1−x Ge x films deposited by chemical vapour deposition
- 20 November 2013
- Published by Springer Nature in Applied Physics A
- Vol. 116 (2) , 751-757
Influence of germanium incorporation on the structural and electrical properties of boron-doped ultrathin poly-Si1−x Ge x films deposited by chemical vapour deposition