BRBranislav Rakicevic

Branislav Rakicevic

*This is an algorithmically generated author record based on publicly available information.

Branislav Rakicevic has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Contribution to the investigation of the influence of tire non-uniformity on the lateral tire characteristics

    by Milena Žunjić, Miroslav Demić, Branislav Rakićević, Branislav Đorđević

    Tire models are widely used in research in the field of vehicle dynamics and noise, and especially in the simulation of their movement under the action of forces and moments. In general case, we distinguish theoretical models defined on the basis of tire construction and empirical or semi-empirical models based on experimental tests. In addition, a combination of these two types of models can also produce tire models. In practice, there is a very wide range of mathematical tire models defined using finite element analysis, by approximation of polynomials of different degrees, by approximation of magic formula, etc. In this paper, an attempt is made to calculate non-stationary lateral characteristics of tires on the basis of experimental stationary lateral characteristics, using two-parameter higher level polynomials. This polynomials define the tire lateral characteristics, and take into account their non-uniformity. More specifically, the lateral characteristics are approximated as a function of the dynamic change of the slip angle, radial load due to tire non-uniformity and time.


  • Open Access

    The effects of gear shift indicator usage on fuel efficiency of a motor vehicle

    by Ivan Blagojevic, Goran Vorotovic, Dragan Stamenkovic, Nebojsa Petrovic, Branislav Rakicevic

    The manner of gear shifting is one of the main factors affecting the fuel efficiency of motor vehicles. Potential savings resulted from optimized gear shifting led to introduction of gear shift indicators in passenger vehicles as an obligation from year 2012. The effects of gear shift indicators usage are still not studied enough. That was the motive for the authors to conduct the experiments to justify their usage, both from the economic and ecological standpoint. The presented results come from the tests conducted on FIAT 500L vehicle to determine the fuel consumption using the new European driving cycle, but for three different gear shift patterns: (1) as defined in UNECE Regulation No. 83, (2) as indicated by vehicle?s gear shift indicator, and (3) based on the average vehicle speed values collected from gear shift indicators of 35 passenger vehicles of different makes, types, and characteristics. Maximum difference in fuel consumption recorded in tests done using three different gear shift patterns is 18.7%.


  • Open Access

    The analysis of gear shift indicator test results

    by Ivan A. Blagojević, Dragan D. Stamenković, Branislav B. Rakićević

    The results of tests according to Regulation (EU) No 65/2012 regarding gear shift indicators on 59 different vehicles are analyzed. Primary parameters were the vehicle speeds at which the gear shift is indicated through gear shift indicator (GSI), and based on their deviation from standard gear shift points defined for type I emission tests in UNECE Regulation No 83, it is concluded that standard gear shift points need to be revised. Relative fuel savings when shifting according to GSI instructions compared to standard gear shift points were analyzed (average 5.2%, maximum 19.9%). It is also shown that automaatic transmission gave bigger fuel saving when manual mode is used according to GSI, compared to manual transmission, also used with GSI. It is concluded that statistical analysis on how drivers follow GSI instructions may be used to improve current test procedures for GSI efficiency, fuel consumption measurement and emission tests.


  • Open Access

    Failure analysis of bolted joint for the column of an aerial platform

    by Branislav Rakićević, Miloš Maneski, Saša Mitić, Goran Vorotović, Dražan Kozak, Marko Katinić

  • Open Access

    Industrial safety of pressure vessels - structural integrity point of view

    by Aleksandar Sedmak, Mahdi Algool, Snezana Kirin, Branislav Rakicevic, Ramo Bakic

    This paper presents different aspects of pressure vessel safety in the scope of industrial safety, focused to the chemical industry. Quality assurance, including application of PED97/23 has been analysed first, followed shortly by the risk assessment and in details by the structural integrity approach, which has been illustrated with three case studies. One important conclusion, following such an approach, is that so-called water proof testing can actually jeopardize integrity of a pressure vessel instead of proving it.


  • Optimisation of maintenance concept choice using risk-decision factor – a case study

    by Vladimir M. Popovic, Branko M. Vasic, Branislav B. Rakicevic, Goran S. Vorotovic

    The design of maintenance system and the corresponding logistic support is a very complex process, during which the aim is to find the compromise solutions regarding the relations among different maintenance procedures and the ways of their implementation. As a result of this, various solutions can be adopted, since this is conditioned by a series of important factors and criteria, which can be contradictory sometimes. There are different perspectives on ways of solving practical maintenance problems, that is dilemmas when it comes to the choice of maintenance concept. The principal dilemma is how and when to decide on carrying out maintenance procedures. Should the decision be based on theoretical grounds or experience, how does one reconcile those two extremes, who is to decide upon this? In this article we have offered one, basically new solution as a possibility for maintenance concept choice, based on a significant modification of the widely used failure modes and effects analysis (FMEA) method. This solution is risk-decision factor (RDF). This is a result of seven parameters (of different importance and weight) that have the key impact on the process of production and logistic support. The application of this factor is illustrated by the example of planning, organisation and functioning of the maintenance system applied in The Institute for Manufacturing Banknotes and Coins (ZIN) in Belgrade.