Christoph Steffan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Christoph Steffan has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Inge Siegl
Development Center Graz, Infineon Technologies Austria AG, Graz, Austria
4 shared publications - Norbert Sailer
Graz University of Technology
4 shared publications - Darshan Shetty
Infineon Technologies Austria AG, Graz, Austria
3 shared publications - Jasmin Grosinger
University of Siegen, Siegen, Germany
3 shared publications - Wolfgang Bosch
Institute of Microwave and Photonic Engineering, Graz University of Technology, Graz, Austria
3 shared publications Gerald Holweg
Infineon Technologies Austria AG, Graz, Austria
2 shared publications
Latest Publications
- Open Access
- 18 July 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 691
Quantitative separation of thermal and electrochemical contributions in nonlinear EIS measurements
- 18 July 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 691
Open AccessQuantitative separation of thermal and electrochemical contributions in nonlinear EIS measurements
- Open Access
- 28 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. PP (15498328) , 1-11
Switched Capacitor Analog Midrange Detector for Eight Voltage Inputs: Design Principles, Characterization, and Performance Demonstration
Changing electrode potentials during electrochemical measurements require dynamic positioning of the electrode’s reference point at runtime. An analog implementation of a midrange detector circuit serves as the sense part to continuously adjust absolute electrode potentials. The midrange detector topology is based on a source-follower winner-take-all circuit and a switched capacitor mean creation. The topology allows simultaneous monitoring of eight voltage input channels. The maximum error is 100 mV over the commercial temperature range of −20 °C to 70 °C. For the relevant operational conditions the error stays even lower. With an average power consumption of 12.06 pW for a sampling frequency of 1.5 MHz the topology is an efficient way to realize dynamic electrode positioning. The application demonstrates that analog computation when applied with care is resource efficient while still having good performance compared to the strategy of immediate analog-to-digital conversion and digital signal processing. This statement is justified by the fact that for an implementation with analog-to-digital converter (ADC) sensing and digital post processing, the analog conversions necessary to reach the same performance would alone require 12.6 pW with the best published ADCs at the moment.
- 28 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. PP (15498328) , 1-11
Open AccessSwitched Capacitor Analog Midrange Detector for Eight Voltage Inputs: Design Principles, Characterization, and Performance Demonstration
Changing electrode potentials during electrochemical measurements require dynamic positioning of the electrode’s reference point at runtime. An analog implementation of a midrange detector circuit serves as the sense part to continuously adjust absolute electrode potentials. The midrange detector topology is based on a source-follower winner-take-all circuit and a switched capacitor mean creation. The topology allows simultaneous monitoring of eight voltage input channels. The maximum error is 100 mV over the commercial temperature range of −20 °C to 70 °C. For the relevant operational conditions the error stays even lower. With an average power consumption of 12.06 pW for a sampling frequency of 1.5 MHz the topology is an efficient way to realize dynamic electrode positioning. The application demonstrates that analog computation when applied with care is resource efficient while still having good performance compared to the strategy of immediate analog-to-digital conversion and digital signal processing. This statement is justified by the fact that for an implementation with analog-to-digital converter (ADC) sensing and digital post processing, the analog conversions necessary to reach the same performance would alone require 12.6 pW with the best published ADCs at the moment.
- Open Access
- 13 January 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 667
Practical considerations and limitations of online EIS-based battery internal temperature estimation in traction applications
- 13 January 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 667
Open AccessPractical considerations and limitations of online EIS-based battery internal temperature estimation in traction applications
- Open Access
- 4 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (1) , 21-25
Fully Passive RF Wake-Up Receiver Including a Small Loop Antenna With −30.7-dBm Sensitivity at 26-kbps Bitrate
This brief presents a fully passive RF wake-up receiver (WuRX) fabricated in a 130 nm CMOS process with a matched small loop antenna. The WuRX consists of a high-sensitivity RF energy harvester that supplies the circuitry necessary for passive WuRX functionality. The circuit consists of an on-chip voltage reference, current reference, power-on reset, low-dropout regulator, relaxation oscillator, envelope detector, comparator, and a digital processor. The WuRX supports an input bitrate of 26 kbps and has a user-defined 12-bit wake-up pattern. Measurements at 830 MHz reveal a wake-up sensitivity of -30.7 dBm and a 1 V harvested output sensitivity of -31 dBm. The RF-powered fully-passive WuRX paves the way for autonomous batteryless sensor nodes.
- 4 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (1) , 21-25
Open AccessFully Passive RF Wake-Up Receiver Including a Small Loop Antenna With −30.7-dBm Sensitivity at 26-kbps Bitrate
This brief presents a fully passive RF wake-up receiver (WuRX) fabricated in a 130 nm CMOS process with a matched small loop antenna. The WuRX consists of a high-sensitivity RF energy harvester that supplies the circuitry necessary for passive WuRX functionality. The circuit consists of an on-chip voltage reference, current reference, power-on reset, low-dropout regulator, relaxation oscillator, envelope detector, comparator, and a digital processor. The WuRX supports an input bitrate of 26 kbps and has a user-defined 12-bit wake-up pattern. Measurements at 830 MHz reveal a wake-up sensitivity of -30.7 dBm and a 1 V harvested output sensitivity of -31 dBm. The RF-powered fully-passive WuRX paves the way for autonomous batteryless sensor nodes.
- Open Access
- 1 July 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (7) , 073507
A Holistic Presentation of 3-Electrode Potentiostat Measurement Data: The Hexa-Region Plot
There is no standardizedpractice for presenting compliance voltage data generated during a 3-electrode potentiostatic measurement. As a result, engineers are sometimes unaware about the electrical requirements their sensor or cell inhibits. This paper proposes a method to compactly display all electrical information . The introduction of a six region voltage plot, with the cell current plotted in the third dimension, achieves a holistic potentiostat data presentation. The proposed method revealscompliance voltage demands, fosters understanding of a sensor’s electric behavior, enables a comparison of potentiostat capabilities, and most importantly, standardizes results across potentiostat platforms.
- 1 July 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (7) , 073507
Open AccessA Holistic Presentation of 3-Electrode Potentiostat Measurement Data: The Hexa-Region Plot
There is no standardizedpractice for presenting compliance voltage data generated during a 3-electrode potentiostatic measurement. As a result, engineers are sometimes unaware about the electrical requirements their sensor or cell inhibits. This paper proposes a method to compactly display all electrical information . The introduction of a six region voltage plot, with the cell current plotted in the third dimension, achieves a holistic potentiostat data presentation. The proposed method revealscompliance voltage demands, fosters understanding of a sensor’s electric behavior, enables a comparison of potentiostat capabilities, and most importantly, standardizes results across potentiostat platforms.
- Open Access
- 6 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 70 (3) , 1030-1042
Ultra-Low-Power Sub-1 V 29 ppm/°C Voltage Reference and Shared-Resistive Current Reference
This paper presents a curvature-compensated sub-1V voltage reference (VR) and a shared-resistive nanoampere current reference (CR) in a 130nm CMOS process. The CR is used to generate a bipolar junction transistor complementary-to-absolute-temperature voltage, which is summed up with a proportional-to-absolute-temperature voltage generated using a summing network of PMOS gate-coupled pairs. The measured output voltage and current references from 10 chips ( $V_{\mathrm {REF}}$ and $I_{\mathrm {REF}}$ ) at room temperature are 469mV and 1.86nA, respectively. The measured average temperature coefficient of $V_{\mathrm {REF}}$ and $I_{\mathrm {REF}}$ are 29ppm $/^{\circ} \text{C}$ and 822ppm $/^{\circ} \text{C}$ over a temperature range from $- 40^{\circ} \text{C}$ to $120^{\circ} \text{C}$ . The minimum supply voltage of the voltage-current reference is 0.95V, and the total power consumption is 30nW.
- 6 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 70 (3) , 1030-1042
Open AccessUltra-Low-Power Sub-1 V 29 ppm/°C Voltage Reference and Shared-Resistive Current Reference
This paper presents a curvature-compensated sub-1V voltage reference (VR) and a shared-resistive nanoampere current reference (CR) in a 130nm CMOS process. The CR is used to generate a bipolar junction transistor complementary-to-absolute-temperature voltage, which is summed up with a proportional-to-absolute-temperature voltage generated using a summing network of PMOS gate-coupled pairs. The measured output voltage and current references from 10 chips ( $V_{\mathrm {REF}}$ and $I_{\mathrm {REF}}$ ) at room temperature are 469mV and 1.86nA, respectively. The measured average temperature coefficient of $V_{\mathrm {REF}}$ and $I_{\mathrm {REF}}$ are 29ppm $/^{\circ} \text{C}$ and 822ppm $/^{\circ} \text{C}$ over a temperature range from $- 40^{\circ} \text{C}$ to $120^{\circ} \text{C}$ . The minimum supply voltage of the voltage-current reference is 0.95V, and the total power consumption is 30nW.
- 16 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Optimized Signal Generation in Pulse Voltammetry for Segmented R-String DACs
Generic user inputs for pulsed techniques in electrochemical measurement systems result in challenging requirements for the digital-to-analog converter (DAC). This paper presents an application-aware excitation scheme for segmented R-string DACs which minimizes the impact of DAC non-idealities on differential pulse voltammetry (DPV) and normal pulse voltammetry (NPV). The proposed algorithm reduces the step deviation from 90% to 4% when applied to the 16 bit resistor string (R-string) DAC of an integrated circuit potentiostat. Results point out that application-aware DAC control helps to lower demands on the DAC while omitting hardware calibration, thus enabling the realization of low-cost point-of-care (POC) devices.
- 16 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Optimized Signal Generation in Pulse Voltammetry for Segmented R-String DACs
Generic user inputs for pulsed techniques in electrochemical measurement systems result in challenging requirements for the digital-to-analog converter (DAC). This paper presents an application-aware excitation scheme for segmented R-string DACs which minimizes the impact of DAC non-idealities on differential pulse voltammetry (DPV) and normal pulse voltammetry (NPV). The proposed algorithm reduces the step deviation from 90% to 4% when applied to the 16 bit resistor string (R-string) DAC of an integrated circuit potentiostat. Results point out that application-aware DAC control helps to lower demands on the DAC while omitting hardware calibration, thus enabling the realization of low-cost point-of-care (POC) devices.
- 29 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (11) , 4803-4812
Submicrowatt CMOS Rectifier for a Fully Passive Wake-Up Receiver
This work presents a wide-range, submicrowatt CMOS rectifier, which is designed to efficiently work at input power levels down to −31 dBm. The designed rectifier uses a novel threshold voltage compensation design, namely, the design of a custom-built single-stage rectifier that supplies a nanowatt current reference circuit. The generated bias current is mirrored to the core rectifier in order to precharge its CMOS diodes. The rectifier was optimized for a minimum number of gain stages while trying to minimize the overall input parasitic capacitance of the rectifier. The proposed CMOS rectifier was designed in an in-house 130-nm CMOS technology and includes a 1.6-kV human body level ESD protection at the input terminals. Measurements reveal a high 30% power conversion efficiency (PCE) over a wide input power range from −23 to −13 dBm for a 1-${\mathrm{ M}}\Omega $ output load at 868 MHz. PCE of over 10% is achieved for a 1-${\mathrm{ M}}\Omega $ load at an input power of −28 dBm. The enhanced startup at submicrowatt input power levels of the CMOS rectifier enables the design of an ultralow-power passive wake-up receiver. The measured sensitivity of −31 dBm for a 1-V output voltage across a capacitive load is the lowest reported in the literature so far.- 29 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (11) , 4803-4812
Submicrowatt CMOS Rectifier for a Fully Passive Wake-Up Receiver
This work presents a wide-range, submicrowatt CMOS rectifier, which is designed to efficiently work at input power levels down to −31 dBm. The designed rectifier uses a novel threshold voltage compensation design, namely, the design of a custom-built single-stage rectifier that supplies a nanowatt current reference circuit. The generated bias current is mirrored to the core rectifier in order to precharge its CMOS diodes. The rectifier was optimized for a minimum number of gain stages while trying to minimize the overall input parasitic capacitance of the rectifier. The proposed CMOS rectifier was designed in an in-house 130-nm CMOS technology and includes a 1.6-kV human body level ESD protection at the input terminals. Measurements reveal a high 30% power conversion efficiency (PCE) over a wide input power range from −23 to −13 dBm for a 1-${\mathrm{ M}}\Omega $ output load at 868 MHz. PCE of over 10% is achieved for a 1-${\mathrm{ M}}\Omega $ load at an input power of −28 dBm. The enhanced startup at submicrowatt input power levels of the CMOS rectifier enables the design of an ultralow-power passive wake-up receiver. The measured sensitivity of −31 dBm for a 1-V output voltage across a capacitive load is the lowest reported in the literature so far.- 3 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 3, 298-301
A Bidirectional Current-Mirror-Based Potentiostat Using a Slice-Based Class-AB Amplifier
A pico-ampere sensitive electrochemical sensor signal acquisition chain consisting of a multi-channel bidirectional current-mirror based potentiostat and a multiplexed current-input delta-sigma (Σ) ADC is presented. Slice-based class-AB amplifiers with output stage current replication using reconfigurable current-mirrors enable bidirectional current sensing over a range of five decades. The replicated current is digitized by the ADC. The proposed circuit achieves a minimum detectable current of 91.7 pA, resulting in a dynamic range of 147 dB for sensor currents up to ±1 mA. The potentiostat is operated at a 3 V supply, the ADC at 1.5 V. The static power consumption of a single interface channel depends on the number of active amplifier slices and is between 14.1 W and 39.3 W. The highest power efficiency among similar systems and the low voltage headroom consumption of less than 500 mV enables a versatile use of the interface for multiple sensing applications.
- 3 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 3, 298-301
A Bidirectional Current-Mirror-Based Potentiostat Using a Slice-Based Class-AB Amplifier
A pico-ampere sensitive electrochemical sensor signal acquisition chain consisting of a multi-channel bidirectional current-mirror based potentiostat and a multiplexed current-input delta-sigma (Σ) ADC is presented. Slice-based class-AB amplifiers with output stage current replication using reconfigurable current-mirrors enable bidirectional current sensing over a range of five decades. The replicated current is digitized by the ADC. The proposed circuit achieves a minimum detectable current of 91.7 pA, resulting in a dynamic range of 147 dB for sensor currents up to ±1 mA. The potentiostat is operated at a 3 V supply, the ADC at 1.5 V. The static power consumption of a single interface channel depends on the number of active amplifier slices and is between 14.1 W and 39.3 W. The highest power efficiency among similar systems and the low voltage headroom consumption of less than 500 mV enables a versatile use of the interface for multiple sensing applications.