Jingyao Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jingyao Li has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Rui Yin
School of Information Science and Engineering, Shandong University, Qingdao, China
2 shared publications - Wei Ji
The School of Information Science and Engineering, Shandong University, QingDao, China
2 shared publications - Zerui Song
School of Information Science and Engineering, Shandong University, Qingdao, China
2 shared publications - Hao Yun
Laboratory of Intelligent Communications and Multimedia Information Processing, Shandong University, Qingdao, China
1 shared publication - Qingjie Huang
Shandong Univ, Sch Informat Sci & Engn, Jinan 250100, Peoples R China
1 shared publication - Zisu Gong
School of Information Science and Engineering, and Shandong Provincial Key Laboratory of Laser Technology and Application, Shandong University
1 shared publication
Latest Publications
- Open Access
- 4 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 136419-136437
Highly Reliable Metro-Access Network Based on a Dual-Fiber Ring Architecture and Optimized Protection Mechanisms
Network reliability is very important for the next generation of optical networks. In this paper, a highly reliable protection mechanism, which integrates the approaches of optical protection and microwave protection, is proposed for metro-access optical networks based on the wavelength division multiplexing (WDM) technique. By designing a scheme for the convergence of optical and wireless access and cooperating with designed remote nodes (RNs), not only can access for both wired and wireless service be provided simultaneously in each optical network unit (ONU) but also microwave protection can be realized when a failure occurs in a distribution segment. By developing a novel optical switch module (OSM) to cooperate with the dual-fiber ring structure, flexible switching can be achieved to protect against multiple types of failures in the feeder segment, including single-fiber faults, dual-fiber faults and multifiber faults. Based on the above structure, the influence of Rayleigh backscattering (RB) noise can be mitigated when the network is operating under all operating scenarios except for an inner-fiber fault. To further mitigate the influence of noise, optimization for upstream transmission performance is implemented by configuring a reflective semiconductor optical amplifier (RSOA). Furthermore, the feasibility of the overall scheme is verified through experiments and simulations under different operating conditions. The results show that the proposed mechanisms can achieve acceptable bit error rate performance and quality of service (QoS) metrics while also offering various advantages, including high reliability, large scale, and a relatively low cost.
- 4 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 136419-136437
Open AccessHighly Reliable Metro-Access Network Based on a Dual-Fiber Ring Architecture and Optimized Protection Mechanisms
Network reliability is very important for the next generation of optical networks. In this paper, a highly reliable protection mechanism, which integrates the approaches of optical protection and microwave protection, is proposed for metro-access optical networks based on the wavelength division multiplexing (WDM) technique. By designing a scheme for the convergence of optical and wireless access and cooperating with designed remote nodes (RNs), not only can access for both wired and wireless service be provided simultaneously in each optical network unit (ONU) but also microwave protection can be realized when a failure occurs in a distribution segment. By developing a novel optical switch module (OSM) to cooperate with the dual-fiber ring structure, flexible switching can be achieved to protect against multiple types of failures in the feeder segment, including single-fiber faults, dual-fiber faults and multifiber faults. Based on the above structure, the influence of Rayleigh backscattering (RB) noise can be mitigated when the network is operating under all operating scenarios except for an inner-fiber fault. To further mitigate the influence of noise, optimization for upstream transmission performance is implemented by configuring a reflective semiconductor optical amplifier (RSOA). Furthermore, the feasibility of the overall scheme is verified through experiments and simulations under different operating conditions. The results show that the proposed mechanisms can achieve acceptable bit error rate performance and quality of service (QoS) metrics while also offering various advantages, including high reliability, large scale, and a relatively low cost.
- 20 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 20 (16) , 8903-8911
Customizable Optical Pressure Sensor Based on Optimized Asymmetric Mach–Zehnder Interferometer: A Review
In this paper, we verify the feasibility of our proposed design scheme for customizable optical pressure sensor based on the photo-elastic effect of SiO2 waveguide in asymmetric Mach-Zehnder interferometer (a-MZI) structure. The curve lengths and minimum radii of curvature of several common types of a-MZI arm curves are calculated theoretically. By analyzing the relationship between the radius of curvature of the long arm curve, the length of the long arm curve and the arm length difference of the a-MZI sensor under different types of arm curves, the design scheme for an a-MZI pressure sensor with a specific arm length difference is obtained. By selecting a rationalized arm design scheme, customization of the sensing range can be achieved. No special processing (such as etching) is required for the waveguide, which improves the pressure tolerance of the sensor. When using the SiO2 waveguide with a refractive index difference of 2%, the a-MZI pressure sensor based on sine type arm with arm length difference of 5 mm has a sensing range of 4.83 MPa and a sensitivity of 1.24 mW/MPa. The a-MZI pressure sensor with the ease of fabrication can be used to monitor various scenarios, such as marine and building monitoring.
- 20 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 20 (16) , 8903-8911
Customizable Optical Pressure Sensor Based on Optimized Asymmetric Mach–Zehnder Interferometer: A Review
In this paper, we verify the feasibility of our proposed design scheme for customizable optical pressure sensor based on the photo-elastic effect of SiO2 waveguide in asymmetric Mach-Zehnder interferometer (a-MZI) structure. The curve lengths and minimum radii of curvature of several common types of a-MZI arm curves are calculated theoretically. By analyzing the relationship between the radius of curvature of the long arm curve, the length of the long arm curve and the arm length difference of the a-MZI sensor under different types of arm curves, the design scheme for an a-MZI pressure sensor with a specific arm length difference is obtained. By selecting a rationalized arm design scheme, customization of the sensing range can be achieved. No special processing (such as etching) is required for the waveguide, which improves the pressure tolerance of the sensor. When using the SiO2 waveguide with a refractive index difference of 2%, the a-MZI pressure sensor based on sine type arm with arm length difference of 5 mm has a sensing range of 4.83 MPa and a sensitivity of 1.24 mW/MPa. The a-MZI pressure sensor with the ease of fabrication can be used to monitor various scenarios, such as marine and building monitoring.