IHIntissar Harrabi

Intissar Harrabi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Intissar Harrabi has a total of 4 co-authors. Here are the top co-authors by number of shared publications:

  • Majdi Hazami

    Thermal Process Laboratory, Research and Technologies Centre of Energy, Hammam-Lif, Tunisia

    4 shared publications
  • Mohamed Hamdi

    Laboratory of Wind Power Control and Waste Energy Recovery, Research and Technologies Centre of Energy, Hammam-Lif, Tunisia

    2 shared publications
  • Mohamed Hamdi

    Laboratory for the Study of Thermal & Energy Systems, National Engineering School of Monastir, Street Ibn El Jazzar, Monastir 5019, Tunisia

    2 shared publications
  • Amira Bessifi

    Thermal Process Laboratory, Research and Technology Centre of Energy, Hammam-Lif, Tunisia

    1 shared publication

Latest Publications

  • Potential of simple and hybrid nanofluid enhancement in performances of a flat plate solar water heater under a typical North-African climate (Tunisia)

    by Intissar Harrabi, Mohamed Hamdi, Majdi Hazami

    This work aims to quantify the long-term performance improvement of solar water heater system by using both simple and hybrid nanofluids. For this purpose, transient system simulations of a flat plate solar collector have been carried out and discussed using titanium oxide, magnesium oxide, and copper oxide/multiwalled oxide–carbon nanotube nanofluid-based nanoparticles. Tunisian climatic conditions with a typical household need has been considered, and the investigations have been established in terms of energy amounts, solar fractions, and harmful CO2 emission avoidance. Results showed an increase in the collector performances using the considered nanofluids. In particular, using 0.2v% and 0.6v% TiO2 homogeneously dispersed in water reduced the auxiliary energy up to 47.6 and 60.9%, respectively, compared to the reference case using water. The flat plate solar collector has an annual production of 1294 kWh for a need of 1998 kWh, which equates to an annual coverage rate of roughly 65%. Additionally, it was shown that when MgO with MWCNT were used instead of MgO nanofluid-based nanoparticles, the solar fraction increased by 5.14%. The use of 0.6 volume percent TiO2 nanoparticles in water reduces hazardous CO2 emissions by up to 0.829 tons annually.


  • Open Access

    Long-Term Performances and Technoeconomic and Environmental Assessment of Al2O3/Water and MWCNT/Oil Nanofluids in Three Solar Collector Technologies

    by Intissar Harrabi, Mohamed Hamdi, Majdi Hazami

    Bringing together nanofluids and solar collectors has been widely discussed without any major advance or long-term study being carried out. In this context, this paper provides a useful feasibility study to help future decisions in using nanofluids in Solar Water Heating Systems (SWHSs) in different locations. The performances of SWHSs using the nanofluid-based flat plate solar collector (FPSC), evacuated tube collector (ETC), and compound parabolic collector (CPC) under the Mediterranean, arctic, and desert climate conditions are presented and discussed. The analysis is carried out using a transient-based numerical approach, solving energy balance equations for different systems. Various performance factors such as energy saving, solar fractions, and environmental impacts of auxiliary energy supplies are evaluated to feasibly assess the use of nanofluids in such devices. Simulation results demonstrate that the use of nanofluids increases the solar heater performance which reduces considerably the payback period () of the investment in solar heating systems up to 3.34 years in Tunisian climate. Under Quebec’s climate region, the annualized solar return of the ETC system increases from 4874.65 US$ to 9785.93 US$ by adding 0.06 v% Al2O3 in water. Also, the use of nanofluids in solar collectors with electric auxiliary heaters reduces harmful CO2 emissions up to 0.49 tons/year.


  • Open Access

    Assessment of Uncertainties in Energetic and Exergetic Performances of a Flat Plate Solar Water Heater

    by Intissar Harrabi, Mohamed Hamdi, Majdi Hazami

    This paper aims to quantify sensitivities of energy and exergy performances of Flat Plate Solar Water Heaters (FPSWHs) with respect to measurement parameters. For that purpose, a computational tool is developed and validated by using outdoor conditions according to the test standard EN 12975. First of all, numerical simulations are compared with experimental results and available data in the literature, and the comparison shows a good agreement. Then, we apply the proposed model to the quantification of uncertainties associated with transient simulation. Results show that ambient temperature is the main relevant factor in operating conditions, and its effect reaches 13.7% and 3.89% on energy and exergy efficiencies, respectively, when the deviation in the sensor measurement is about ±1°C. When 0.15 v% multiwall carbon nanotubes (MWCNT)-Ethylene-Glycol (E-G) (30 : 70) nanofluid is used as working fluid, results show that a suitable choice of nanofluid properties achieves 84.7% of the thermal efficiency during the zero reduced temperature conditions compared to 75.4% when the collector works with E-G. Using common empirical correlations affects substantially the accuracy of the fitting parameters, and the deviation in exergy efficiency reaches 1.18%.