Tian Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tian Yang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Qinyuan Huang
School of Automation and information Engineering, Sichuan University of Science and Engineering, Zigong, China
3 shared publications - Qiang Li
Department of Automation, China University of Petroleum, Beijing, China
2 shared publications - Ying Zhou
School of Automation and information Engineering, Sichuan University of Science and Engineering, Zigong, China
2 shared publications Hong Song
1 shared publicationKun Yang
1 shared publication- Kun Yang
School of Automation and Information Engineering, Sichuan University of Science and Engineering, Zigong 643000, China
1 shared publication
Latest Publications
- Open Access
- 6 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (4) , 2078
A Lightweight Transfer Learning Model with Pruned and Distilled YOLOv5s to Identify Arc Magnet Surface Defects
Surface defects in arc magnets constitute the main culprit for performance degradation and safety hazards in permanent magnet motors. Machine-vision methods offer the possibility to identify surface defects automatically. However, the current methods still do not adequately solve the problems of low identification accuracy, excessive dependency on training data, and sizeable computational complexity. This paper proposes a lightweight YOLOv5s-based transfer learning model with network pruning and knowledge distillation to address these issues. Our model was derived from a pre-trained YOLOv5s for general object detection. A transfer learning mechanism was designed to obtain the optimal surface defect identification accuracy of the model from fewer training samples. Network pruning and knowledge distillation were combined to compress the transferred model. The transferred model serves as the teacher model of knowledge distillation, while its pruned model acts as the student model. To weaken the loss of the accuracy after model compression, a new λ factor was introduced into the confidence loss function of the student model to increase the sensitivity of identifying the defects. The experimental results show that our model’s performance is higher than other regular lightweight models. The identification accuracy for different defective arc magnets could reach 100%, the model size could achieve 1.921 MB, and the average inference time was 9.46 ms. Our model also has high accuracy in other defect identification applications besides arc magnets.
- 6 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (4) , 2078
Open AccessA Lightweight Transfer Learning Model with Pruned and Distilled YOLOv5s to Identify Arc Magnet Surface Defects
Surface defects in arc magnets constitute the main culprit for performance degradation and safety hazards in permanent magnet motors. Machine-vision methods offer the possibility to identify surface defects automatically. However, the current methods still do not adequately solve the problems of low identification accuracy, excessive dependency on training data, and sizeable computational complexity. This paper proposes a lightweight YOLOv5s-based transfer learning model with network pruning and knowledge distillation to address these issues. Our model was derived from a pre-trained YOLOv5s for general object detection. A transfer learning mechanism was designed to obtain the optimal surface defect identification accuracy of the model from fewer training samples. Network pruning and knowledge distillation were combined to compress the transferred model. The transferred model serves as the teacher model of knowledge distillation, while its pruned model acts as the student model. To weaken the loss of the accuracy after model compression, a new λ factor was introduced into the confidence loss function of the student model to increase the sensitivity of identifying the defects. The experimental results show that our model’s performance is higher than other regular lightweight models. The identification accuracy for different defective arc magnets could reach 100%, the model size could achieve 1.921 MB, and the average inference time was 9.46 ms. Our model also has high accuracy in other defect identification applications besides arc magnets.
- 27 August 2022
- Published by Elsevier in Measurement
- Vol. 202
Internal defects inspection of arc magnets using multi-head attention-based CNN
- 27 August 2022
- Published by Elsevier in Measurement
- Vol. 202
Internal defects inspection of arc magnets using multi-head attention-based CNN
- Open Access
- 10 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 71446-71460
Combined Convolutional and LSTM Recurrent Neural Networks for Internal Defect Detection of Arc Magnets Under Strong Noises and Variable Object Types
This paper focuses on developing the acoustic-based detection of arc magnet internal defects under different noises and object types. The major challenge in such a detection case is that the traditional approaches mainly rely on expert knowledge and experiential features, which results in a poor generalization performance of the algorithm for new types of detection objects and is susceptible to noise interference. This work presents a novel detection framework based on an end-to-end one-dimensional (1D) convolutional long short-term memory (LSTM) model, where both the spatial and temporal features of the measured acoustic signals are extracted and then jointed for determining the internal defects of arc magnets. In addition, the LSTM layers are employed behind the 1D convolutional neural network, which makes the number of time steps in the LSTM layers for the temporal feature extraction is much smaller than the length of the input segments, thus the computational complexity of the LSTM layers can be highly reduced. Experimental results show that our method is superior to existed methods in the detection accuracy for the internal defects of arc magnets, and the diagnosis time per a single arc magnet is controlled at the millisecond, making it appropriate for real-time applications. Furthermore, the robustness of the proposed framework is validated through experiments on different signal-to-ratios and multiple object types of arc magnets.
- 10 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 71446-71460
Open AccessCombined Convolutional and LSTM Recurrent Neural Networks for Internal Defect Detection of Arc Magnets Under Strong Noises and Variable Object Types
This paper focuses on developing the acoustic-based detection of arc magnet internal defects under different noises and object types. The major challenge in such a detection case is that the traditional approaches mainly rely on expert knowledge and experiential features, which results in a poor generalization performance of the algorithm for new types of detection objects and is susceptible to noise interference. This work presents a novel detection framework based on an end-to-end one-dimensional (1D) convolutional long short-term memory (LSTM) model, where both the spatial and temporal features of the measured acoustic signals are extracted and then jointed for determining the internal defects of arc magnets. In addition, the LSTM layers are employed behind the 1D convolutional neural network, which makes the number of time steps in the LSTM layers for the temporal feature extraction is much smaller than the length of the input segments, thus the computational complexity of the LSTM layers can be highly reduced. Experimental results show that our method is superior to existed methods in the detection accuracy for the internal defects of arc magnets, and the diagnosis time per a single arc magnet is controlled at the millisecond, making it appropriate for real-time applications. Furthermore, the robustness of the proposed framework is validated through experiments on different signal-to-ratios and multiple object types of arc magnets.