Xintu Lin
Xintu Lin has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Ruijie Jin
4 shared publicationsYincai Wu
4 shared publications- Yuejun Liu
Key Laboratory of Advanced Packaging Materials and Technology of Hunan Province Hunan University of Technology Zhuzhou China
4 shared publications Ruilan Xu
3 shared publicationsWei Zheng
3 shared publicationsXi Chen
3 shared publications
Latest Publications
- 1 November 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1046
Ultrathin asymmetric porous PLA bilayers with electrical-magnetic synergy for absorption-dominated EMI shielding
- 1 November 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1046
Ultrathin asymmetric porous PLA bilayers with electrical-magnetic synergy for absorption-dominated EMI shielding
- 1 September 2025
- Published by Wiley in Polymer Composites
- Vol. 47 (5) , 3971-3982
Absorption‐Dominant Electromagnetic Shielding in Ultrathin PLA Composite Films Through Engineered MWCNTs @Ag and Multilayer Architecture
Low‐thickness, eco‐friendly electromagnetic interference (EMI) shielding materials with high shielding effectiveness (SE) are urgently needed to address escalating electromagnetic pollution in miniaturized electronic devices. Herein, we synthesized silver nanoparticle‐decorated multiwalled carbon nanotubes (MWCNTs@Ag) via a rapid solvent‐free method and integrated them into poly(lactic acid) (PLA) matrices to fabricate composite films through solution casting. The resulting PLA/MWCNTs@Ag composite film containing 10 wt% MWCNTs@Ag achieves an average EMI SE of 18.59 dB at a thickness of approximately 95 μm, with the shielding mechanism dominated by surface reflection. To strategically control EMI attenuation pathways, multilayered architectures were engineered using layer‐by‐layer solution casting while maintaining identical filler content. Systematic analysis reveals that both thickness and layer number significantly influence EMI shielding performance. Notably, a multilayer film with a thickness of approximately 155 μm and seven layers exhibits an average EMI SE of 24.43 dB with an absorption‐dominated mechanism, showing a 31.41% enhancement over single‐layer counterparts. This performance transition from reflection to absorption dominance originates from optimized impedance matching, enhanced interfacial polarization, multiple internal reflections, and reconstructed conductive networks enabled by structural design. The synergy between hierarchical structure engineering and hybrid filler incorporation provides new insights for developing sustainable high‐performance EMI shielding materials.
- 1 September 2025
- Published by Wiley in Polymer Composites
- Vol. 47 (5) , 3971-3982
Absorption‐Dominant Electromagnetic Shielding in Ultrathin PLA Composite Films Through Engineered MWCNTs @Ag and Multilayer Architecture
Low‐thickness, eco‐friendly electromagnetic interference (EMI) shielding materials with high shielding effectiveness (SE) are urgently needed to address escalating electromagnetic pollution in miniaturized electronic devices. Herein, we synthesized silver nanoparticle‐decorated multiwalled carbon nanotubes (MWCNTs@Ag) via a rapid solvent‐free method and integrated them into poly(lactic acid) (PLA) matrices to fabricate composite films through solution casting. The resulting PLA/MWCNTs@Ag composite film containing 10 wt% MWCNTs@Ag achieves an average EMI SE of 18.59 dB at a thickness of approximately 95 μm, with the shielding mechanism dominated by surface reflection. To strategically control EMI attenuation pathways, multilayered architectures were engineered using layer‐by‐layer solution casting while maintaining identical filler content. Systematic analysis reveals that both thickness and layer number significantly influence EMI shielding performance. Notably, a multilayer film with a thickness of approximately 155 μm and seven layers exhibits an average EMI SE of 24.43 dB with an absorption‐dominated mechanism, showing a 31.41% enhancement over single‐layer counterparts. This performance transition from reflection to absorption dominance originates from optimized impedance matching, enhanced interfacial polarization, multiple internal reflections, and reconstructed conductive networks enabled by structural design. The synergy between hierarchical structure engineering and hybrid filler incorporation provides new insights for developing sustainable high‐performance EMI shielding materials.
- 27 June 2024
- Published by Elsevier in Thermochimica Acta
- Vol. 739
Manipulation of non-isothermal crystallization kinetics of poly(lactic acid) composite film by a novel nucleating agent
- 27 June 2024
- Published by Elsevier in Thermochimica Acta
- Vol. 739
Manipulation of non-isothermal crystallization kinetics of poly(lactic acid) composite film by a novel nucleating agent
- 31 May 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 140 (32)
Structure evolution and properties enhancement of polyamide‐6/polyamide‐1010 films under uniaxial and biaxial stretching
The effect of stretching process on the structures and properties of the stretch‐oriented PA6/PA1010 film was investigated during the uniaxial and biaxial stretching. The results showed that the PA6/PA1010 cast film exhibited β‐form crystals, and the uniaxial stretching induced the β → α + γ phase transition and preferential orientation along the stretching direction, while the β → α phase transition and no preferential orientation were observed during the biaxial stretching process. Meanwhile, the melting temperature and crystallinity of PA6 in uniaxially and biaxially stretched PA6/PA1010 films were improved with the increasing stretching ratios, thus creating a much more tortuous pathway for the diffusion of oxygen molecules to enhance the oxygen barrier property of the stretched films after uniaxial and biaxial stretching. The morphological analysis showed that the PA1010 particles were oriented and deformed along the stretching direction and no obvious debonding and voids were observed at the interface. In addition, the mechanical properties of the stretched films were closely dependent upon the stretching ratios. It was found that the tensile strength of the biaxially stretched PA6/PA1010 films with stretching ratio of 3.5 × 3.5 in MD and TD exhibited about 1.7 times and 2.2 times higher than that of the PA6/PA1010 cast film, respectively.
- 31 May 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 140 (32)
Structure evolution and properties enhancement of polyamide‐6/polyamide‐1010 films under uniaxial and biaxial stretching
The effect of stretching process on the structures and properties of the stretch‐oriented PA6/PA1010 film was investigated during the uniaxial and biaxial stretching. The results showed that the PA6/PA1010 cast film exhibited β‐form crystals, and the uniaxial stretching induced the β → α + γ phase transition and preferential orientation along the stretching direction, while the β → α phase transition and no preferential orientation were observed during the biaxial stretching process. Meanwhile, the melting temperature and crystallinity of PA6 in uniaxially and biaxially stretched PA6/PA1010 films were improved with the increasing stretching ratios, thus creating a much more tortuous pathway for the diffusion of oxygen molecules to enhance the oxygen barrier property of the stretched films after uniaxial and biaxial stretching. The morphological analysis showed that the PA1010 particles were oriented and deformed along the stretching direction and no obvious debonding and voids were observed at the interface. In addition, the mechanical properties of the stretched films were closely dependent upon the stretching ratios. It was found that the tensile strength of the biaxially stretched PA6/PA1010 films with stretching ratio of 3.5 × 3.5 in MD and TD exhibited about 1.7 times and 2.2 times higher than that of the PA6/PA1010 cast film, respectively.
- 8 March 2022
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (19)
Cover Image, Volume 139, Issue 19
- 8 March 2022
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (19)
Cover Image, Volume 139, Issue 19
- 28 January 2022
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (19) , 52152
Structural evolution and properties of polyamide‐6/poly(ether block amide) films during the simultaneous biaxial stretching
The purpose of this study was to investigate the structural evolution and properties of simultaneously biaxially stretched polyamide‐6/poly(ether block amide) copolymer (PA6/PEBA) films. The results showed the melting temperature of PA6 increased from 220.02°C to 225.56°C when the stretching ratios increased from 1 × 1 to 3.5 × 3.5, suggesting the occurrence of β → α crystal transformation. Meanwhile, the increase of stretching ratios increased the crystallinity of the films due to the molecular orientation, which could create a more tortuous path for the diffusion of oxygen molecules through the films. As a result, the oxygen barrier performance of the stretched PA6/PEBA film was increased after biaxial stretching. The morphological observation showed that spherical or slightly ellipsoidal PEBA particles were dispersed in the PA6 matrix. The thermal shrinkage of the stretched film increased as the stretching ratios increased, and no significant difference of the shrinkage between machine direction (MD) and transition direction (TD) was observed in the stretched films. It was also found that the tensile strength of the stretched films in MD and TD exhibited the highest value at a stretching ratio of 3.5 × 3.5, which was about 1.7 times and 2.1 times higher than that of the unstretched PA6/PEBA film, respectively.
- 28 January 2022
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (19) , 52152
Structural evolution and properties of polyamide‐6/poly(ether block amide) films during the simultaneous biaxial stretching
The purpose of this study was to investigate the structural evolution and properties of simultaneously biaxially stretched polyamide‐6/poly(ether block amide) copolymer (PA6/PEBA) films. The results showed the melting temperature of PA6 increased from 220.02°C to 225.56°C when the stretching ratios increased from 1 × 1 to 3.5 × 3.5, suggesting the occurrence of β → α crystal transformation. Meanwhile, the increase of stretching ratios increased the crystallinity of the films due to the molecular orientation, which could create a more tortuous path for the diffusion of oxygen molecules through the films. As a result, the oxygen barrier performance of the stretched PA6/PEBA film was increased after biaxial stretching. The morphological observation showed that spherical or slightly ellipsoidal PEBA particles were dispersed in the PA6 matrix. The thermal shrinkage of the stretched film increased as the stretching ratios increased, and no significant difference of the shrinkage between machine direction (MD) and transition direction (TD) was observed in the stretched films. It was also found that the tensile strength of the stretched films in MD and TD exhibited the highest value at a stretching ratio of 3.5 × 3.5, which was about 1.7 times and 2.1 times higher than that of the unstretched PA6/PEBA film, respectively.
- 13 September 2021
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 33 (1) , 137-145
Crystal structure, morphology, and mechanical properties of biaxially oriented polyamide‐6 films toughened with poly(ether block amide)
Biaxially oriented polyamide‐6 (BOPA) film has been widely used in many packaging applications. However, the BOPA film with excellent toughness is still required when utilizing in the field of soft‐packaged lithium‐ion batteries, pharmaceutical blister packaging, or frozen food packaging especially for vacuum packaging of irregular‐shaped food products. The purpose of this study was to improve the toughness of BOPA films by toughening with poly(ether block amide) (PEBA) (BOPA/PEBA films) based on the simultaneous biaxial stretching technology. The crystal structure, morphology, optical properties, barrier, and mechanical properties of BOPA/PEBA films were investigated. The results showed that the incorporation of PEBA into BOPA films slightly decreased the melting temperature and crystallinity of PA6, and the BOPA/PEBA films exhibited only α‐form crystals and no preferential orientation in the machine direction (MD) and transition direction (TD). The morphological observation showed that higher addition of PEBA led to the formation of microvoids due to the poor compatibility between PA6 and PEBA. As a result, the transmittance and oxygen barrier properties of the BOPA/PEBA films decreased. In addition, mechanical analysis suggested that the addition of PEBA could effectively improve the toughness of BOPA film.
- 13 September 2021
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 33 (1) , 137-145
Crystal structure, morphology, and mechanical properties of biaxially oriented polyamide‐6 films toughened with poly(ether block amide)
Biaxially oriented polyamide‐6 (BOPA) film has been widely used in many packaging applications. However, the BOPA film with excellent toughness is still required when utilizing in the field of soft‐packaged lithium‐ion batteries, pharmaceutical blister packaging, or frozen food packaging especially for vacuum packaging of irregular‐shaped food products. The purpose of this study was to improve the toughness of BOPA films by toughening with poly(ether block amide) (PEBA) (BOPA/PEBA films) based on the simultaneous biaxial stretching technology. The crystal structure, morphology, optical properties, barrier, and mechanical properties of BOPA/PEBA films were investigated. The results showed that the incorporation of PEBA into BOPA films slightly decreased the melting temperature and crystallinity of PA6, and the BOPA/PEBA films exhibited only α‐form crystals and no preferential orientation in the machine direction (MD) and transition direction (TD). The morphological observation showed that higher addition of PEBA led to the formation of microvoids due to the poor compatibility between PA6 and PEBA. As a result, the transmittance and oxygen barrier properties of the BOPA/PEBA films decreased. In addition, mechanical analysis suggested that the addition of PEBA could effectively improve the toughness of BOPA film.