ZWZhiqiang Wan

Zhiqiang Wan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Zhiqiang Wan has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Aerodynamic Load Characterisation of Hypersonic Rudders

    by Liang Ma, Zhiqiang Wan, Xiaozhe Wang

  • Nonlinear Aeroelastic Modeling and Post-flutter Analysis of a Highly Flexible Wing

    by Zhiying Chen, Changchuan Xie, Yang Meng, Zhiqiang Wan

  • Open Access

    Fuel Weight Fraction Estimation for a Disk–Rotor Hybrid Aircraft Along an Optimal Flight Trajectory During Concept Design

    by Menglin Yang, Zhiqiang Wan, De Yan, Jingwei Chen

    Owing to the transition flight of rotor/wing hybrid vertical take‐off and landing (VTOL) aircraft, the fuel weight cannot be estimated from empirical data during the conceptual design phase. This paper proposes a method for estimating the minimal fuel weight fraction (FWF) through a strategy of trajectory optimization under a given flight profile. The typical flight profile of a disk–rotor hybrid aircraft is selected, and a dimensionless dynamic model is established for the flight mission segment by introducing the thrust–weight ratio and power–weight ratio. A trajectory optimization strategy is established with the minimum fuel consumption and flight time as the performance index, taking the dynamic model and waypoints on the flight profile as constraints. The Gauss pseudospectral method is used to solve for the minimum FWF of each mission segment, subsequently obtaining the FWF of the whole flight profile, and results are compared with those obtained from the conventional empirical Breguet method, confirming the validity of the approach proposed here. The optimization results demonstrate that the method proposed in this paper enables the comprehensive calculation of the FWF for the entire flight profile without considering the take‐off weight. Furthermore, the impacts of the general and performance‐related parameters associated with the flight profile on the FWF can be observed.

  • Open Access

    Nonlinear Unsteady Aerodynamics Reduced Order Model of Airfoils Based on Algorithm Fusion and Multifidelity Framework

    by Yan Shi, Zhiqiang Wan, Zhigang Wu, Chao Yang

    A reduced order modeling method based on algorithm fusion and multifidelity framework for nonlinear unsteady aerodynamics is proposed to obtain a low-cost and high-precision unsteady aerodynamic model. This method integrates the traditional algorithm, intelligent algorithm, and multifidelity data fusion algorithm. In this method, the traditional algorithm is based on separated flow theory, the intelligent algorithm refers to the nonlinear autoregressive (NARX) method, and the multifidelity data fusion algorithm uses different fidelity data for aerodynamic modeling, which can shorten the time cost of data acquisition. In the process of modeling, firstly, a multifidelity model with NARX description provides a general intelligent algorithm framework for unsteady aerodynamics. Then, based on the separated flow theory, the correction equation from low-fidelity model to high-fidelity result is constructed, and the cuckoo algorithm based on chaos optimization is used to identify the parameters. In order to verify the effectiveness of the method, an unsteady aerodynamic model of NACA0012 airfoil is established. Three kinds of data with low, medium, and high fidelity are used for modeling. The low-fidelity and medium-fidelity data is obtained from the CFD-Euler solver and CFD-RANS solver, respectively, while the high-fidelity data comes from the experimental results. Then, the model is established, and its prediction of unsteady aerodynamic coefficients is in good agreement with the CFD results and the experimental data. After that, the model is applied to a two-dimensional aeroelastic system, and the bifurcation and limit cycle response analysis are compared with the experimental results, which further shows that the model can accurately capture the main flow characteristics in the flow range of low speed and high angle of attack. In addition, the convergence of the model is studied; the accuracy and generalization ability as well as applicability scope of the model are compared with other aerodynamic models and finally discussed.


  • Numerical Analysis of Gas Leakage Problem Based on Improved Gas Storage Vessel Leakage Model

    by Liping Sun, Zhiqiang Wan, Shangmao Ai, Jiaji Li

    The gas leakage accidents always lead to great damages in the process of off-shore oil and gas treatment, consisting of health, wealth and environment losses. When leakage happens, the leakage duration, leak amount and other corresponding parameters are very important on the topic of emergency reaction and decision. The leaking process is complex and cumbersome, so the solving of the leakage problem could be quite difficult. On this point view, a specific and direct solution is given to the leakage problem on the basis of the leakage theory in this paper. According to the improved gas storage vessel leakage model, the mathematical differential method and discretization method are conducted to calculate the result of gaseous container leakage of any kind, consisting of leakage duration, leak amount, residual amount of gas and the residual pressure in the container. There are two probable flowing state of gas during the leakage. So, there is a requirement for different solving methods and principles for gas leakage in different flowing states. There is also calculation for residual amount of gas and residual gas pressure in the container at any given time point. The MATLAB program language is conducted to design the specific computing program and finish the GUI achievement of the program according to the fixed calculative methods and parameters concerned. Carry out the calculation of a fictive leakage problem with the designed MATLAB program, and get the result. It shows that the computing program comes to good leakage result, and the program can also result in acceptable outcome at any chosen time point on the issue of calculating residual amount and residual pressure of gas in the container. The computing program can solve the leakage problem veritably to some degree.