Yucong Ma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yucong Ma has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Yuanhua Lin
School of New Energy and Materials, Southwest Petroleum University, Chengdu, China
3 shared publications - Mohd Talha
Department of Chemistry, Faculty of Science
2 shared publications Qi Wang
State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Chengdu 610500, Sichuan, P. R. China
2 shared publicationsZhonghui Li
School of Petroleum Engineering, Yangtze University, Wuhan, 434023, Hubei, China
2 shared publications- Arup Kumar Mandal
Department of Metallurgical and Materials Engineering, National Institute of Technology Durgapur, Durgapur, India
1 shared publication Mohd Talha
School of New Energy and Materials Southwest Petroleum University Chengdu Sichuan China
1 shared publication
Latest Publications
- 15 February 2022
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 46 (9) , 4436-4448
A multifunctional coating with modified calcium phosphate/chitosan for biodegradable magnesium alloys of implants
Magnesium (Mg) alloys with outstanding biocompatibility and mechanical properties are extensively used in medical implantation. However, the rapid degradation and potential cytotoxicity in the physiological environment limit their further clinical applications. In this study, we prepared a calcium phosphate/chitosan (CaP/CTS) coating by chemical conversion and dip-coating methods to increase the corrosion resistance, biocompatibility and antibacterial property of the Mg alloy. The surface morphology, electrochemical and immersion tests signified that the CaP/CTS coating showed a significantly improved corrosion resistance because the chitosan efficiently filled the cracks and reduced the porosity of the CaP coating. In vitro investigation of cell response and contact angle experiments confirmed that the composite coating had excellent cytocompatibility and hydrophilicity. In addition, the composite coating demonstrated a prominent antibacterial ability of 95.9 ± 0.4% against Escherichia coli (E.coli). The strengthened corrosion resistance, biocompatibility and antibacterial property of the CaP/CTS coating deposited Mg alloy make it an up-and-coming prospect in the field of implants.
- 15 February 2022
- Published by Royal Society of Chemistry (RSC) in New Journal of Chemistry
- Vol. 46 (9) , 4436-4448
A multifunctional coating with modified calcium phosphate/chitosan for biodegradable magnesium alloys of implants
Magnesium (Mg) alloys with outstanding biocompatibility and mechanical properties are extensively used in medical implantation. However, the rapid degradation and potential cytotoxicity in the physiological environment limit their further clinical applications. In this study, we prepared a calcium phosphate/chitosan (CaP/CTS) coating by chemical conversion and dip-coating methods to increase the corrosion resistance, biocompatibility and antibacterial property of the Mg alloy. The surface morphology, electrochemical and immersion tests signified that the CaP/CTS coating showed a significantly improved corrosion resistance because the chitosan efficiently filled the cracks and reduced the porosity of the CaP coating. In vitro investigation of cell response and contact angle experiments confirmed that the composite coating had excellent cytocompatibility and hydrophilicity. In addition, the composite coating demonstrated a prominent antibacterial ability of 95.9 ± 0.4% against Escherichia coli (E.coli). The strengthened corrosion resistance, biocompatibility and antibacterial property of the CaP/CTS coating deposited Mg alloy make it an up-and-coming prospect in the field of implants.
- 1 December 2021
- Published by Wiley in Materials and Corrosion
- Vol. 73 (3) , 436-450
Nano‐silica/chitosan composite coatings on biodegradable magnesium alloys for enhanced corrosion resistance in simulated body fluid
Chitosan (CTS) coatings have been studied as a biocompatible coating on biodegradable magnesium (Mg) alloys to improve the corrosion resistance and bioactivity for medical implants. However, the loose structure of the CTS coating cannot provide ideal long‐time corrosion resistance in the physiological environment. In this study, a nano‐SiO2/CTS composite coating was applied on an Mg alloy substrate using the sol–gel method. The surface characteristics of the samples were examined by Fourier‐transform infrared analysis, X‐ray diffraction, scanning electron microscopy‐energy‐dispersive spectrometry, and contact angle measurements. The particle size and suitable dispersion of the SiO2 nanoparticles inside the composite coating were confirmed by transmission electron microscopy. Further, the corrosion protection behavior of the coatings was examined in a simulated body fluid using potentiodynamic polarization, electrochemical impedance spectroscopy, and scanning electrochemical microscopy analyses. Atomic force microscopy was used to determine the surface morphologies of the samples after the polarization test. The surface characteristics, electrochemical measurements, and immersion test revealed that the SiO2 nanoparticles effectively filled the voids of the CTS coating and significantly improved the corrosion resistance. The optimal concentration of nano‐SiO2 is 1.0 g/L.
- 1 December 2021
- Published by Wiley in Materials and Corrosion
- Vol. 73 (3) , 436-450
Nano‐silica/chitosan composite coatings on biodegradable magnesium alloys for enhanced corrosion resistance in simulated body fluid
Chitosan (CTS) coatings have been studied as a biocompatible coating on biodegradable magnesium (Mg) alloys to improve the corrosion resistance and bioactivity for medical implants. However, the loose structure of the CTS coating cannot provide ideal long‐time corrosion resistance in the physiological environment. In this study, a nano‐SiO2/CTS composite coating was applied on an Mg alloy substrate using the sol–gel method. The surface characteristics of the samples were examined by Fourier‐transform infrared analysis, X‐ray diffraction, scanning electron microscopy‐energy‐dispersive spectrometry, and contact angle measurements. The particle size and suitable dispersion of the SiO2 nanoparticles inside the composite coating were confirmed by transmission electron microscopy. Further, the corrosion protection behavior of the coatings was examined in a simulated body fluid using potentiodynamic polarization, electrochemical impedance spectroscopy, and scanning electrochemical microscopy analyses. Atomic force microscopy was used to determine the surface morphologies of the samples after the polarization test. The surface characteristics, electrochemical measurements, and immersion test revealed that the SiO2 nanoparticles effectively filled the voids of the CTS coating and significantly improved the corrosion resistance. The optimal concentration of nano‐SiO2 is 1.0 g/L.
- 1 January 2021
- Published by Elsevier in Colloids and Surfaces B: Biointerfaces
- Vol. 197, 111407
Corrosion performance of various deformed surfaces of implant steel for coronary stent applications: Effect of protein concentration
- 1 January 2021
- Published by Elsevier in Colloids and Surfaces B: Biointerfaces
- Vol. 197, 111407
Corrosion performance of various deformed surfaces of implant steel for coronary stent applications: Effect of protein concentration