Havva Neslihan Kıray
Research Subjects
Havva Neslihan Kıray has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Cengiz Zabcı
Istanbul Teknik Üniversitesi
7 shared publications - Mehmet Köküm
Firat Universitesi
4 shared publications - Asen Sabuncu3 shared publications
Gürsel Sunal
3 shared publicationsH. Serdar Akyüz
3 shared publicationsMusa Balkaya
3 shared publications
Latest Publications
- Open Access
- 20 January 2025
- Published by Copernicus GmbH
Primary Surface Rupture and Slip Distribution Associated with the Mw 7.6 06 February 2023 Elbistan Earthquake, Turkey
The February 06, 2023, Kahramanmaraş earthquake sequence started with an earthquake with magnitude Mw 7.0 on the Narlı Fault and continued on the tectonic boundary between the Anatolian and Arabian plates. The main event, the Mw 7.8 Pazarcik earthquake, ruptured the East Anatolian Fault (EAF) bilaterally for over 300 km. This main event was followed nine hours later by the Mw 7.6 Elbistan earthquake, with the epicenter near the town of Ekinözü, about 100 kilometers away from the epicenter of the Pazarcik earthquake. The Elbistan earthquake also ruptured bilaterally, resulting in approximately 140 km of co-seismic surface rupture along a set of faults that form a major splay of the East Anatolian Fault Zone. Field investigations supplemented with interpretations of high-resolution photographs from small unmanned aircraft systems and helicopters show that the surface rupture associated with the Elbistan earthquake occurred on two different left-lateral strike faults: The first, known as the Çardak fault, extends from the town of Göksun in the west to Bıçakçı village in the east. The second is the newly identified Yeşilyurt Fault, an NE-SW-striking left-lateral fault with a subtle topographic expression that strikes parallel to the EAF. The surface trace of the Çardak Fault can be divided into two geometric sections: The arc-shaped western section extends nearly 80 km between Göksun and Nurhak where the rupture was continuous and focused within a narrow zone. Horizontal slip along the eastern half of this section was typically over 6 meters, reaching over 8 meters at the maximum slip location just east of the epicenter. The average lateral slip drops to approximately 4 meters west of Ericek before decreasing uniformly to the west from Fındık until the surface rupture ends in Göksun. The second fault section extends nearly E-W between Nurhak and Bıçakçı for almost 20 km, including the structurally complex region associated with the Nurhak restraining bend, where only a handful of field slip measurements were made in this broadly deformed section. The average minimum horizontal slip measurements in this section of the Çardak fault is around 2.5 m. Our field investigations indicate that the rupture established a new trend parallel to the East Anatolian Fault instead of using the E-W-oriented Sürgü Fault to connect with it. The average slip along this new 40 km-long fault zone, here named Yeşilyurt Fault, is about 1m, with maximum left-lateral slip reaching ~2.5m. Unlike the nearly continuous rupture along the Çardak fault, the rupture zone of the Yeşilyurt Fault generally consists of a series of right-stepping en-echelon arrays of discontinuous sinistral fault traces of various lengths and stepovers that range between tens of meters to several hundred meters.
- 20 January 2025
- Published by Copernicus GmbH
Open AccessPrimary Surface Rupture and Slip Distribution Associated with the Mw 7.6 06 February 2023 Elbistan Earthquake, Turkey
The February 06, 2023, Kahramanmaraş earthquake sequence started with an earthquake with magnitude Mw 7.0 on the Narlı Fault and continued on the tectonic boundary between the Anatolian and Arabian plates. The main event, the Mw 7.8 Pazarcik earthquake, ruptured the East Anatolian Fault (EAF) bilaterally for over 300 km. This main event was followed nine hours later by the Mw 7.6 Elbistan earthquake, with the epicenter near the town of Ekinözü, about 100 kilometers away from the epicenter of the Pazarcik earthquake. The Elbistan earthquake also ruptured bilaterally, resulting in approximately 140 km of co-seismic surface rupture along a set of faults that form a major splay of the East Anatolian Fault Zone. Field investigations supplemented with interpretations of high-resolution photographs from small unmanned aircraft systems and helicopters show that the surface rupture associated with the Elbistan earthquake occurred on two different left-lateral strike faults: The first, known as the Çardak fault, extends from the town of Göksun in the west to Bıçakçı village in the east. The second is the newly identified Yeşilyurt Fault, an NE-SW-striking left-lateral fault with a subtle topographic expression that strikes parallel to the EAF. The surface trace of the Çardak Fault can be divided into two geometric sections: The arc-shaped western section extends nearly 80 km between Göksun and Nurhak where the rupture was continuous and focused within a narrow zone. Horizontal slip along the eastern half of this section was typically over 6 meters, reaching over 8 meters at the maximum slip location just east of the epicenter. The average lateral slip drops to approximately 4 meters west of Ericek before decreasing uniformly to the west from Fındık until the surface rupture ends in Göksun. The second fault section extends nearly E-W between Nurhak and Bıçakçı for almost 20 km, including the structurally complex region associated with the Nurhak restraining bend, where only a handful of field slip measurements were made in this broadly deformed section. The average minimum horizontal slip measurements in this section of the Çardak fault is around 2.5 m. Our field investigations indicate that the rupture established a new trend parallel to the East Anatolian Fault instead of using the E-W-oriented Sürgü Fault to connect with it. The average slip along this new 40 km-long fault zone, here named Yeşilyurt Fault, is about 1m, with maximum left-lateral slip reaching ~2.5m. Unlike the nearly continuous rupture along the Çardak fault, the rupture zone of the Yeşilyurt Fault generally consists of a series of right-stepping en-echelon arrays of discontinuous sinistral fault traces of various lengths and stepovers that range between tens of meters to several hundred meters.
- Open Access
- 20 January 2025
- Published by Copernicus GmbH
February 2023 Kahramanmaraş Earthquake Sequence: ‘supercycle’ events within a complex tectonic setting
On 6 February 2023, a series of earthquakes struck south-eastern Türkiye and northern Syria, causing a death toll of more than 50.000 people and an economic loss of billions of US Dollars. The devastating sequence started with the Mw ~7.0 Narlı Earthquake along a subsidiary splay, which was then instantly followed by the Mw 7.8 Pazarcık Earthquake bilaterally rupturing multiple structural elements in a complex triple junction system. These were followed ~9 hours later by the Mw 7.6 Elbistan Earthquake that took place on the Çardak and the Yeşilyurt faults. The involvement of multiple faults and the immense size of the affected region raise multiple questions such as the controlling factors, especially on the extent of the rupture length, slip distribution, width of the rupture zone, and any potential seismic gaps that were brought closer to failure.This study aims to present our field investigations and measurement for the 6 February 2023 earthquakes with a particular emphasis on the tectonic complexity of the region. We have constructed a detailed surface rupture map and documented hundreds of offset measurements that suggest up to ~7 and ~8.5 meters of maximum sinistral displacements, for the Pazarcık and Elbistan earthquakes, respectively. The co-seismic slips differ from the offsets of the penultimate event in places, suggesting a variable slip behaviour, especially for the Çardak Fault. Our map does not only include the Principal Displacement Shear (PDS), but also almost all the secondary shears that provide an opportunity to determine the deformation width along the faults. One of the widest zones of surface breaks is observed within the Palaeozoic metamorphics and Mesozoic limestones of the Nurhak Mountain along the Çardak rupture, highlighting the influence of structural complexities on the distribution of deformation. A similar control occurs at the northeastern tip of the Pazarcık Rupture, which terminates in another structural complexity where the left-lateral East Anatolian Fault (EAF) connects with the Bitlis-Zagros suture zone. Field data suggests that this structural junction is responsible for arresting the rupture along the EAF, not the southern termination of the 24 January 2020 Mw 6.8 Sivrice (Elazığ) Earthquake rupture, producing a ‘seismic gap’ of about 20 km. To the south, the Pazarcık rupture reached the Dead Sea Fault, which has not had a significant surface rupturing earthquake to the north of Aqaba since the early 11th century. Despite the widespread destruction that razed several towns to the ground, the 2023 Kahramanmaraş Earthquake Sequence provides invaluable information on understanding the geometry and kinematics of active faulting that accommodate the Eurasia-Africa-Arabia convergence in the eastern Mediterranean.
- 20 January 2025
- Published by Copernicus GmbH
Open AccessFebruary 2023 Kahramanmaraş Earthquake Sequence: ‘supercycle’ events within a complex tectonic setting
On 6 February 2023, a series of earthquakes struck south-eastern Türkiye and northern Syria, causing a death toll of more than 50.000 people and an economic loss of billions of US Dollars. The devastating sequence started with the Mw ~7.0 Narlı Earthquake along a subsidiary splay, which was then instantly followed by the Mw 7.8 Pazarcık Earthquake bilaterally rupturing multiple structural elements in a complex triple junction system. These were followed ~9 hours later by the Mw 7.6 Elbistan Earthquake that took place on the Çardak and the Yeşilyurt faults. The involvement of multiple faults and the immense size of the affected region raise multiple questions such as the controlling factors, especially on the extent of the rupture length, slip distribution, width of the rupture zone, and any potential seismic gaps that were brought closer to failure.This study aims to present our field investigations and measurement for the 6 February 2023 earthquakes with a particular emphasis on the tectonic complexity of the region. We have constructed a detailed surface rupture map and documented hundreds of offset measurements that suggest up to ~7 and ~8.5 meters of maximum sinistral displacements, for the Pazarcık and Elbistan earthquakes, respectively. The co-seismic slips differ from the offsets of the penultimate event in places, suggesting a variable slip behaviour, especially for the Çardak Fault. Our map does not only include the Principal Displacement Shear (PDS), but also almost all the secondary shears that provide an opportunity to determine the deformation width along the faults. One of the widest zones of surface breaks is observed within the Palaeozoic metamorphics and Mesozoic limestones of the Nurhak Mountain along the Çardak rupture, highlighting the influence of structural complexities on the distribution of deformation. A similar control occurs at the northeastern tip of the Pazarcık Rupture, which terminates in another structural complexity where the left-lateral East Anatolian Fault (EAF) connects with the Bitlis-Zagros suture zone. Field data suggests that this structural junction is responsible for arresting the rupture along the EAF, not the southern termination of the 24 January 2020 Mw 6.8 Sivrice (Elazığ) Earthquake rupture, producing a ‘seismic gap’ of about 20 km. To the south, the Pazarcık rupture reached the Dead Sea Fault, which has not had a significant surface rupturing earthquake to the north of Aqaba since the early 11th century. Despite the widespread destruction that razed several towns to the ground, the 2023 Kahramanmaraş Earthquake Sequence provides invaluable information on understanding the geometry and kinematics of active faulting that accommodate the Eurasia-Africa-Arabia convergence in the eastern Mediterranean.
- Open Access
- 20 January 2025
- Published by Copernicus GmbH
February 2023 Mw 7.8 Pazarcık (Kahramanmaraş) Earthquake: the rupture geometry and slip distribution
February 2023 Mw 7.8 Pazarcık (Kahramanmaraş) Earthquake generated about a 300 km-long surface rupture between the Antakya airport to the south and the Karaköse and Yarpuzlu villages (Sincik, Adıyaman) to the north and strong ground motions, resulting in extensive property damage and loss of lives. We rapidly started to document the deformation structures on the surface by the second day of the event, spreading into smaller mapping teams and covering nearly the entire rupture zone. In addition to walking the rupture and recording locations with GPS waypoints, we made surface offset measurements with a standard tape measure. We used several sUAS’ to acquire high-resolution Digital Orthophoto Maps and Digital Surface Models (between 3 to 5 cm pixel resolution) to map the coseismic slip and surface rupture zone details. We utilized high resolution stereo aerial images with 10 or 30 cm ground pixel resolution, collected by the General Directorate of Mapping, in areas where we could not collect high-quality sUAS imagery.This poster presentation aims to show the full extent of our field and sUAS-based rupture map and horizontal slip measurements of the Pazarcık Earthquake. At the most southern section, the rupture along the Hatay Rift is ~115 km long with a maximum sinistral offset of about 4.5 m between Nurdağ and Şekeroba towns. Between Türkoğlu and Gölbaşı, the rupture is 85 km long and the maximum slip reaches up to ~7m to the north of the Pazarcık town, close to the junction of the East Anatolian and Narlı faults. Farther to the NE, between Gölbaşı and Çelikhan, the slip first decreases to a mean value of ~2.5 m, but then it increases again to ~6.5 m at Kurucaova village. This section of the fault zone is nearly one km wide and is characterized by numerous sub-parallel surface breaks. To the north east of Çelikhan, the slip drops to less than one meter. It diminishes to the north of the Karaköse village (Sincik, Adıyaman), leaving of about 20 km-long unbroken fault section at the surface until the southwest termination of the 2020 Mw 6.8 Sivrice Earthquake rupture.
- 20 January 2025
- Published by Copernicus GmbH
Open AccessFebruary 2023 Mw 7.8 Pazarcık (Kahramanmaraş) Earthquake: the rupture geometry and slip distribution
February 2023 Mw 7.8 Pazarcık (Kahramanmaraş) Earthquake generated about a 300 km-long surface rupture between the Antakya airport to the south and the Karaköse and Yarpuzlu villages (Sincik, Adıyaman) to the north and strong ground motions, resulting in extensive property damage and loss of lives. We rapidly started to document the deformation structures on the surface by the second day of the event, spreading into smaller mapping teams and covering nearly the entire rupture zone. In addition to walking the rupture and recording locations with GPS waypoints, we made surface offset measurements with a standard tape measure. We used several sUAS’ to acquire high-resolution Digital Orthophoto Maps and Digital Surface Models (between 3 to 5 cm pixel resolution) to map the coseismic slip and surface rupture zone details. We utilized high resolution stereo aerial images with 10 or 30 cm ground pixel resolution, collected by the General Directorate of Mapping, in areas where we could not collect high-quality sUAS imagery.This poster presentation aims to show the full extent of our field and sUAS-based rupture map and horizontal slip measurements of the Pazarcık Earthquake. At the most southern section, the rupture along the Hatay Rift is ~115 km long with a maximum sinistral offset of about 4.5 m between Nurdağ and Şekeroba towns. Between Türkoğlu and Gölbaşı, the rupture is 85 km long and the maximum slip reaches up to ~7m to the north of the Pazarcık town, close to the junction of the East Anatolian and Narlı faults. Farther to the NE, between Gölbaşı and Çelikhan, the slip first decreases to a mean value of ~2.5 m, but then it increases again to ~6.5 m at Kurucaova village. This section of the fault zone is nearly one km wide and is characterized by numerous sub-parallel surface breaks. To the north east of Çelikhan, the slip drops to less than one meter. It diminishes to the north of the Karaköse village (Sincik, Adıyaman), leaving of about 20 km-long unbroken fault section at the surface until the southwest termination of the 2020 Mw 6.8 Sivrice Earthquake rupture.
- Open Access
- 20 January 2025
- Published by Copernicus GmbH
The Narlı Fault: the characteristics of the surface rupture that initiated the 6 February 2023 Kahramanmaraş Earthquake Sequence (Türkiye)
The south-southeastern Türkiye was struck by a series of earthquakes in February 2023 causing the death of more than 50,000 people and billions of USD of economical loss. The largest of these events, the February 6th Mw 7.8 Pazarcık and Mw 7.5 Ekinözü earthquakes occurred only 9 hours apart of each other generating surface ruptures of about 450 km and the majority of the destruction. All these events took place in a complex tectonic system where the boundary structures of the Anatolian Block, the Arabian Plate and the Adana-Cilicia-Hatay Basin merge together. The Pazarcık earthquake was initiated along a subsidiary splay, the Narlı Fault (NF), and continued with the bilateral rupturing of faults over a length of 300 km.In this study, our aim is to document the surface deformation along the NF in order to have a better understanding of the initiation mechanism of the ‘multi-segment’ Pazarcık earthquake. In addition to our field observations, we operated a sUAS to map the rupture and measure offsets. We used a tape measure to determine the magnitude of slip across the well-established offset markers in the field, while the ultra-precise rupture mapping and a vast number of displacement measurements were made by using sUAS-based digital surface models (DSM) and orthophotos with a ground pixel resolution of ~3–5 cm.We mapped two sets of continuous surface ruptures, the 14 km-long southern and the 10 km-long northern parts, separated by a ‘gap’ of 8 km. The average sinistral offset along the ~N20-30°–striking southern rupture is about 2 m, whereas the maximum value reaches up to 3.7 ± 0.7 meters. On the other hand, the horizontal slip along the N25-35°–striking northern rupture barely exceeds 1.2 m. In this section, it is highly probable that a large portion of the total horizontal deformation is shared by widely distributed surface shears within the wedge between the East Anatolian Fault and the NF, which can be an analogue to a variant of a Prandtl Cell Model. In addition, we identified semi-circular/elliptical surface cracks at more than 10 locations to the south of the NF rupture. These are interpreted as seismically induced sink-holes, given the widely distributed Eocene limestones in the region. The preliminary analysis of the time series of interferograms between 2015–2022 suggests a long-term systematic subsidence, supporting our hypothesis.
- 20 January 2025
- Published by Copernicus GmbH
Open AccessThe Narlı Fault: the characteristics of the surface rupture that initiated the 6 February 2023 Kahramanmaraş Earthquake Sequence (Türkiye)
The south-southeastern Türkiye was struck by a series of earthquakes in February 2023 causing the death of more than 50,000 people and billions of USD of economical loss. The largest of these events, the February 6th Mw 7.8 Pazarcık and Mw 7.5 Ekinözü earthquakes occurred only 9 hours apart of each other generating surface ruptures of about 450 km and the majority of the destruction. All these events took place in a complex tectonic system where the boundary structures of the Anatolian Block, the Arabian Plate and the Adana-Cilicia-Hatay Basin merge together. The Pazarcık earthquake was initiated along a subsidiary splay, the Narlı Fault (NF), and continued with the bilateral rupturing of faults over a length of 300 km.In this study, our aim is to document the surface deformation along the NF in order to have a better understanding of the initiation mechanism of the ‘multi-segment’ Pazarcık earthquake. In addition to our field observations, we operated a sUAS to map the rupture and measure offsets. We used a tape measure to determine the magnitude of slip across the well-established offset markers in the field, while the ultra-precise rupture mapping and a vast number of displacement measurements were made by using sUAS-based digital surface models (DSM) and orthophotos with a ground pixel resolution of ~3–5 cm.We mapped two sets of continuous surface ruptures, the 14 km-long southern and the 10 km-long northern parts, separated by a ‘gap’ of 8 km. The average sinistral offset along the ~N20-30°–striking southern rupture is about 2 m, whereas the maximum value reaches up to 3.7 ± 0.7 meters. On the other hand, the horizontal slip along the N25-35°–striking northern rupture barely exceeds 1.2 m. In this section, it is highly probable that a large portion of the total horizontal deformation is shared by widely distributed surface shears within the wedge between the East Anatolian Fault and the NF, which can be an analogue to a variant of a Prandtl Cell Model. In addition, we identified semi-circular/elliptical surface cracks at more than 10 locations to the south of the NF rupture. These are interpreted as seismically induced sink-holes, given the widely distributed Eocene limestones in the region. The preliminary analysis of the time series of interferograms between 2015–2022 suggests a long-term systematic subsidence, supporting our hypothesis.
- Open Access
- 20 January 2025
- Published by Copernicus GmbH
Unveiling the Kinematics of the 2022 Düzce Earthquake (Mw 5.9) and Its Impact on Regional Tectonics
In 1999, The North Anatolian Fault (NAF) generated two destructive earthquakes, namely, the Mw 7.4 Izmit earthquake and the Mw 7.1 Düzce earthquake, in the western part of Türkiye and broke more than 180 km of NAF. After 22 years of silence, at the overlapping section of these ruptures, the region produced two earthquakes: one with a magnitude of 5 and another, a year later, with a magnitude of 5.9. In this study, we aim to examine the role of these recent earthquakes in terms of slip deficit between two ruptures.Our primary focus is on the Düzce earthquake (Mw 5.9) that occurred on 23 November 2022. Here we use a novel method to reconstruct the coseismic deformation field by enhancing the signal-to-noise ratio (SNR) from ~3 years of Interferometric Synthetic Aperture Radar (InSAR) Sentinel-1 TOPS data spanning the earthquake. We estimate a coseismic surface displacement of ~2 cm for this event.Furthermore, data from the stations belonging to the Turkish National GNSS Network and data from eight new cGPS sites that we have established in the area have been processed to observe coseismic and postseismic displacement. Postseismic deformations are estimated for one month interval after the earthquake, maximum postseismic deformation is observed on the site named AKSU: 18.6 ± 2.18 mm at east and -1.5 ± 2.28 mm at north direction.A joint inversion model was developed using the aforementioned geodetic and seismological data to estimate the region's final state and was linked to the potential slip deficit of previous major earthquakes in 1999.
- 20 January 2025
- Published by Copernicus GmbH
Open AccessUnveiling the Kinematics of the 2022 Düzce Earthquake (Mw 5.9) and Its Impact on Regional Tectonics
In 1999, The North Anatolian Fault (NAF) generated two destructive earthquakes, namely, the Mw 7.4 Izmit earthquake and the Mw 7.1 Düzce earthquake, in the western part of Türkiye and broke more than 180 km of NAF. After 22 years of silence, at the overlapping section of these ruptures, the region produced two earthquakes: one with a magnitude of 5 and another, a year later, with a magnitude of 5.9. In this study, we aim to examine the role of these recent earthquakes in terms of slip deficit between two ruptures.Our primary focus is on the Düzce earthquake (Mw 5.9) that occurred on 23 November 2022. Here we use a novel method to reconstruct the coseismic deformation field by enhancing the signal-to-noise ratio (SNR) from ~3 years of Interferometric Synthetic Aperture Radar (InSAR) Sentinel-1 TOPS data spanning the earthquake. We estimate a coseismic surface displacement of ~2 cm for this event.Furthermore, data from the stations belonging to the Turkish National GNSS Network and data from eight new cGPS sites that we have established in the area have been processed to observe coseismic and postseismic displacement. Postseismic deformations are estimated for one month interval after the earthquake, maximum postseismic deformation is observed on the site named AKSU: 18.6 ± 2.18 mm at east and -1.5 ± 2.28 mm at north direction.A joint inversion model was developed using the aforementioned geodetic and seismological data to estimate the region's final state and was linked to the potential slip deficit of previous major earthquakes in 1999.
- Open Access
- 15 May 2023
- Published by Copernicus GmbH
Influence of fault rocks’ mineralogy on fault behaviour: implications from the Palu-Hazar Lake section of the East Anatolian Fault (Elazığ, Türkiye)
The multi-disciplinary studies yield a more complicated picture on seismic cycles, especially with the increasing evidence on creeping, slow slip events, tremors and repeating earthquakes. Recent observations support triggering of large earthquakes even by small or slow earthquakes and creeping of different portions of the fault. The Palu-Hazar Lake section of the East Anatolian Fault (EAF) is an example place of such kind of behaviour, where the 24 January Mw 6.8 Sivrice Earthquake was nucleated along the neighbouring segments. This sinistral strike-slip fault forms the eastern boundary of the Anatolian Scholle between Karlıova (Bingöl) in the northeast and Türkoğlu (Kahramanmaraş) in the southwest within the complex tectonic frame of the Eastern Mediterranean.In this study, we aim to correlate any potential influence of bedrock lithology on this creeping section of the EAF. First, we revised the active fault and geological maps by using the multi spectral satellite images (e.g., Landsat 8 OLI) and high-resolution digital surface models (~0.65 m ground pixel resolution). Then, we determined potential exposures along the EAF and made systematic sampling both from cohesive and incohesive fault rock exposures within our study region. Collected samples are prepared for X-ray diffraction (XRD) measurements, especially for the determination of the fault clay types. Fault rock samples from ophiolitic (mafic and ultramafic) rocks and accretionary complexes (shale, sandstone, volcanics, ophiolite fragments) are mostly made of vermiculite and include minor amounts of smectite and chlorite according to our XRD measurements. Although the low shear strength of vermiculate may trigger aseismic slip at shallow depths with change in pore water pressure, it is possible that there may be no correlation between bedrock lithology and creeping, considering the poorly known seismic history of the EAF.This study is supported by TÜBİTAK Project no. 118Y435.Keywords: earthquake, East Anatolian Fault, creep, fault rocks
- 15 May 2023
- Published by Copernicus GmbH
Open AccessInfluence of fault rocks’ mineralogy on fault behaviour: implications from the Palu-Hazar Lake section of the East Anatolian Fault (Elazığ, Türkiye)
The multi-disciplinary studies yield a more complicated picture on seismic cycles, especially with the increasing evidence on creeping, slow slip events, tremors and repeating earthquakes. Recent observations support triggering of large earthquakes even by small or slow earthquakes and creeping of different portions of the fault. The Palu-Hazar Lake section of the East Anatolian Fault (EAF) is an example place of such kind of behaviour, where the 24 January Mw 6.8 Sivrice Earthquake was nucleated along the neighbouring segments. This sinistral strike-slip fault forms the eastern boundary of the Anatolian Scholle between Karlıova (Bingöl) in the northeast and Türkoğlu (Kahramanmaraş) in the southwest within the complex tectonic frame of the Eastern Mediterranean.In this study, we aim to correlate any potential influence of bedrock lithology on this creeping section of the EAF. First, we revised the active fault and geological maps by using the multi spectral satellite images (e.g., Landsat 8 OLI) and high-resolution digital surface models (~0.65 m ground pixel resolution). Then, we determined potential exposures along the EAF and made systematic sampling both from cohesive and incohesive fault rock exposures within our study region. Collected samples are prepared for X-ray diffraction (XRD) measurements, especially for the determination of the fault clay types. Fault rock samples from ophiolitic (mafic and ultramafic) rocks and accretionary complexes (shale, sandstone, volcanics, ophiolite fragments) are mostly made of vermiculite and include minor amounts of smectite and chlorite according to our XRD measurements. Although the low shear strength of vermiculate may trigger aseismic slip at shallow depths with change in pore water pressure, it is possible that there may be no correlation between bedrock lithology and creeping, considering the poorly known seismic history of the EAF.This study is supported by TÜBİTAK Project no. 118Y435.Keywords: earthquake, East Anatolian Fault, creep, fault rocks
- Open Access
- 26 March 2022
- Published by Copernicus GmbH
Spatial strain distribution along continental transform faults: insights from morphometric analyses of the Düzce and Mudurnu Valley segments (North Anatolian Fault, NW Turkey)
Continental transform faults are generally known to have widely distributed structures and sparse seismicity, in opposite to their oceanic counterparts. The North Anatolian Shear Zone (NASZ) is an ideal example, where the total deformation is shared between multiple structures especially during its evolutionary stages. The North Anatolian Fault (NAF), the most prominent member of the NASZ, started to form of about 11 Ma in the east and propagated to the west, reaching to the Marmara Sea only a few hundred thousand years ago. This principal displacement zone generally extends as a single strand from its easternmost tip to the west until Bolu for about 900 km. To the west of Bolu, it bifurcates into two branches, Düzce and Mudurnu Valley segments, delimiting the Almacık Flake (AF) respectively to the north and south. Although there is a considerable number of multi-disciplinary studies on the kinematics and history of active faulting within and around the AF, we still have gaps in our knowledge on (a) the ratio of strain distribution, (b) time of formation of bounding fault segments and (c) their evolutionary stages.In order to fulfil some parts of this gap, we studied the major morphometric indices, including hypsometric curve and integral (HI), asymmetry factor (Af), channel concavity (θ), chi (χ) and knickpoint analyses on drainage basins across the whole AF and all surrounding fault segments. Our goal is not only to document the comparative tectonic effect of the bounding fault segments on the topography, but also to test any potential cumulative morphological response to pre- and post-peak structures, especially along the Düzce Segment. Almost all of 83 extracted drainage basins yield high HI values, usually ranging between 0.4 and 0.72, and suggest a rejuvenating morphology compatible with the general ‘uplift hypothesis’ for the AF. In more details, θ and χ values point out the strong and confined effect of the active bounding faults. Moreover, knickpoints do not show evidence for any pre-peak structures rather than recent active faulting. This may be result of limited size, thus ages, of drainage basins, which are cut by bounding faults at both sides of the AF. Alternatively, these fault segments may be older than previous assumptions, whereas the effect of pre- and post-peak shear structures on topography has already been erased mainly by external processes. On the other hand, χ values, based on 0.45 reference θ, suggest a high incision along the western sections of the Mudurnu Valley Segment, which may indicate a strain transfer from north to south. Nevertheless, the breach of a landslide dam of about 5750 years ago and the strong incision of the Mudurnu River following this event to the south of the AF, as suggested by previous studies, can be another reason for this anomaly. Briefly, our preliminary results suggest a strong tectonic control on the AF’s topography mainly due to the activity of the bounding structures. We do not see any morphometric evidence for the secondary (pre- and post-peak) faults in the near past of the NASZ around the AF.
- 26 March 2022
- Published by Copernicus GmbH
Open AccessSpatial strain distribution along continental transform faults: insights from morphometric analyses of the Düzce and Mudurnu Valley segments (North Anatolian Fault, NW Turkey)
Continental transform faults are generally known to have widely distributed structures and sparse seismicity, in opposite to their oceanic counterparts. The North Anatolian Shear Zone (NASZ) is an ideal example, where the total deformation is shared between multiple structures especially during its evolutionary stages. The North Anatolian Fault (NAF), the most prominent member of the NASZ, started to form of about 11 Ma in the east and propagated to the west, reaching to the Marmara Sea only a few hundred thousand years ago. This principal displacement zone generally extends as a single strand from its easternmost tip to the west until Bolu for about 900 km. To the west of Bolu, it bifurcates into two branches, Düzce and Mudurnu Valley segments, delimiting the Almacık Flake (AF) respectively to the north and south. Although there is a considerable number of multi-disciplinary studies on the kinematics and history of active faulting within and around the AF, we still have gaps in our knowledge on (a) the ratio of strain distribution, (b) time of formation of bounding fault segments and (c) their evolutionary stages.In order to fulfil some parts of this gap, we studied the major morphometric indices, including hypsometric curve and integral (HI), asymmetry factor (Af), channel concavity (θ), chi (χ) and knickpoint analyses on drainage basins across the whole AF and all surrounding fault segments. Our goal is not only to document the comparative tectonic effect of the bounding fault segments on the topography, but also to test any potential cumulative morphological response to pre- and post-peak structures, especially along the Düzce Segment. Almost all of 83 extracted drainage basins yield high HI values, usually ranging between 0.4 and 0.72, and suggest a rejuvenating morphology compatible with the general ‘uplift hypothesis’ for the AF. In more details, θ and χ values point out the strong and confined effect of the active bounding faults. Moreover, knickpoints do not show evidence for any pre-peak structures rather than recent active faulting. This may be result of limited size, thus ages, of drainage basins, which are cut by bounding faults at both sides of the AF. Alternatively, these fault segments may be older than previous assumptions, whereas the effect of pre- and post-peak shear structures on topography has already been erased mainly by external processes. On the other hand, χ values, based on 0.45 reference θ, suggest a high incision along the western sections of the Mudurnu Valley Segment, which may indicate a strain transfer from north to south. Nevertheless, the breach of a landslide dam of about 5750 years ago and the strong incision of the Mudurnu River following this event to the south of the AF, as suggested by previous studies, can be another reason for this anomaly. Briefly, our preliminary results suggest a strong tectonic control on the AF’s topography mainly due to the activity of the bounding structures. We do not see any morphometric evidence for the secondary (pre- and post-peak) faults in the near past of the NASZ around the AF.