Hong Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hong Huang has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Jiantao Zeng
State Key Laboratory of Safety and Resilience of Civil Engineering in Mountain Area East China Jiaotong University Nanchang Jiangxi People's Republic of China
2 shared publicationsLiqing Zhang
School of Civil Engineering and Architecture, East China Jiaotong University , Nanchang , 330013 , China
2 shared publicationsBaoguo Han
School of Infrastructure Engineering, Dalian University of Technology , Dalian , 116024 , China
1 shared publication- Kaicheng Xu
State Key Laboratory of Performance Monitoring and Protecting of Rail Transit Infrastructures, Nanchang 330013, China
1 shared publication - Lu Zhou
School of Science East China Jiaotong University Nanchang Jiangxi People's Republic of China
1 shared publication Mengcheng Chen
School of Civil Engineering and Architecture East China Jiao tong University Nanchang China
1 shared publication
Latest Publications
- 2 June 2026
- Published by Wiley in Structural Concrete
Experimental investigation on recycled ceramic aggregate self‐compacting concrete‐filled double‐skin circular steel tubular column under cyclic loading
Concrete‐filled double‐skin steel tube is widely used in high‐rise buildings, wind turbine towers, and offshore platforms. Recycled ceramic aggregate self‐compacting concrete‐filled double‐skin circular steel tube (RCASCCFDCST), a new type of concrete‐filled steel tube composite form in modern construction, formed by filling steel tubes with recycled ceramic self‐compacting concrete that was produced by replacing natural aggregates with waste ceramic aggregate in concrete mixtures. This paper involved both experimental investigations on the behavior of nine RCASCCFDCST specimens subjected to cyclic loading, of which the damage pattern, load–displacement hysteresis curves, skeleton curve, stiffness degradation, ductility, and energy dissipation capacity were analyzed by varying the axial compression ratios, hollow ratios, and the replacement ratios of recycled ceramic aggregate. The results indicated that the hysteresis curve of RCASCCFDCST exhibited a full hysteresis loop with good energy dissipation capacity and high ductility; the cases with recycled ceramic self‐compacting concrete presented a reduction in ultimate load as well as the ductility to those of the ones with normal self‐compacting concrete; the higher axial compression ratios, the lower both the ductility and stiffness; the energy dissipation capacity increased with the increment of axial compression ratios; and the ductility increased with the increment of hollow ratios.
- 2 June 2026
- Published by Wiley in Structural Concrete
Experimental investigation on recycled ceramic aggregate self‐compacting concrete‐filled double‐skin circular steel tubular column under cyclic loading
Concrete‐filled double‐skin steel tube is widely used in high‐rise buildings, wind turbine towers, and offshore platforms. Recycled ceramic aggregate self‐compacting concrete‐filled double‐skin circular steel tube (RCASCCFDCST), a new type of concrete‐filled steel tube composite form in modern construction, formed by filling steel tubes with recycled ceramic self‐compacting concrete that was produced by replacing natural aggregates with waste ceramic aggregate in concrete mixtures. This paper involved both experimental investigations on the behavior of nine RCASCCFDCST specimens subjected to cyclic loading, of which the damage pattern, load–displacement hysteresis curves, skeleton curve, stiffness degradation, ductility, and energy dissipation capacity were analyzed by varying the axial compression ratios, hollow ratios, and the replacement ratios of recycled ceramic aggregate. The results indicated that the hysteresis curve of RCASCCFDCST exhibited a full hysteresis loop with good energy dissipation capacity and high ductility; the cases with recycled ceramic self‐compacting concrete presented a reduction in ultimate load as well as the ductility to those of the ones with normal self‐compacting concrete; the higher axial compression ratios, the lower both the ductility and stiffness; the energy dissipation capacity increased with the increment of axial compression ratios; and the ductility increased with the increment of hollow ratios.
- Open Access
- 1 January 2024
- Published by Walter de Gruyter GmbH in Nanotechnology Reviews
- Vol. 13 (1)
Using nano-CaCO 3 and ceramic tile waste to design low-carbon ultra high performance concrete
China’s annual production of ceramic tiles inevitably produces a large amount of ceramic tile waste, which causes environmental and land occupation problems. Using a high-volume ceramic tile waste to fabricate ultra high performance concrete (UHPC) will reduce the workability and mechanical properties but increase the low-carbon properties. Motivated by such mechanical and low-carbon properties, this study introduced inexpensive, spherical, low-carbon nano-CaCO 3 (NC) to improve the workability and mechanical properties of UHPC with a high volume of ceramic tile waste powder and aggregate (UHPCHCTWPA). The results of this study indicated that NC can improve the workability but shortened the setting times of UHPCHCTWPA. NC also significantly increases the mechanical properties including compressive strength, compressive work, flexural strength, fracture energy, and ratio of flexural strength to compressive strength. It is due to that NC enhances the hydration rate and hydration degree, and optimizes hydration product orientation, size, and distribution. Moreover, compared with UHPC, the UHPCHCTWPA with NC reduces energy intensity, CO 2 emission, and cost by more than 20%. Therefore, adding NC can make UHPCHCTWPA with good workability, mechanical and low-carbon properties and can effectively and quickly utilize ceramic tile waste.
- 1 January 2024
- Published by Walter de Gruyter GmbH in Nanotechnology Reviews
- Vol. 13 (1)
Open AccessUsing nano-CaCO 3 and ceramic tile waste to design low-carbon ultra high performance concrete
China’s annual production of ceramic tiles inevitably produces a large amount of ceramic tile waste, which causes environmental and land occupation problems. Using a high-volume ceramic tile waste to fabricate ultra high performance concrete (UHPC) will reduce the workability and mechanical properties but increase the low-carbon properties. Motivated by such mechanical and low-carbon properties, this study introduced inexpensive, spherical, low-carbon nano-CaCO 3 (NC) to improve the workability and mechanical properties of UHPC with a high volume of ceramic tile waste powder and aggregate (UHPCHCTWPA). The results of this study indicated that NC can improve the workability but shortened the setting times of UHPCHCTWPA. NC also significantly increases the mechanical properties including compressive strength, compressive work, flexural strength, fracture energy, and ratio of flexural strength to compressive strength. It is due to that NC enhances the hydration rate and hydration degree, and optimizes hydration product orientation, size, and distribution. Moreover, compared with UHPC, the UHPCHCTWPA with NC reduces energy intensity, CO 2 emission, and cost by more than 20%. Therefore, adding NC can make UHPCHCTWPA with good workability, mechanical and low-carbon properties and can effectively and quickly utilize ceramic tile waste.
- 15 June 2023
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 210, 108040
Axial compressive behavior of recycled ceramic coarse aggregate concrete-filled steel tubular columns
- 15 June 2023
- Published by Elsevier in Journal of Constructional Steel Research
- Vol. 210, 108040
Axial compressive behavior of recycled ceramic coarse aggregate concrete-filled steel tubular columns
- 1 June 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (2) , 2475-2489
Study on the mechanical behavior of L‐shaped concrete‐filled steel tubular columns under axial compression
In this paper, a total of six different ribbed and two nonribbed L‐shaped concrete‐filled steel tubular (CFST) short columns are designed; finite element modeling and calculations are carried out and verified with measured results. The optimal ribbing method among the ribbing methods applied is proposed. The mechanisms of the longitudinal stress of the concrete, longitudinal stress of the outer steel tube, and lateral compressive stress of the concrete for the L‐shaped CFST short column without ribs and with the optimal ribbing method are compared and analyzed. The results show that the optimal ribbing method involves setting half‐width longitudinal stiffening ribs in the middle of the two wide sides of the L‐shaped steel tube. The stiffening ribs can delay the occurrence of local buckling failure of the steel tube, thus strengthening the restraining effect of the steel tube on the concrete and improving the uniformity of the longitudinal stress of the core concrete. In addition, based on an analysis of a large number of parameters, four methods for calculating the bearing capacity of nonribbed L‐shaped CFST short columns are compared. A design formula for the bearing capacity of ribbed L‐shaped CFST columns is proposed by considering the improvement in the concrete performance. The calculation results agree well with the finite element and experimental results, and the error is <5%.
- 1 June 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (2) , 2475-2489
Study on the mechanical behavior of L‐shaped concrete‐filled steel tubular columns under axial compression
In this paper, a total of six different ribbed and two nonribbed L‐shaped concrete‐filled steel tubular (CFST) short columns are designed; finite element modeling and calculations are carried out and verified with measured results. The optimal ribbing method among the ribbing methods applied is proposed. The mechanisms of the longitudinal stress of the concrete, longitudinal stress of the outer steel tube, and lateral compressive stress of the concrete for the L‐shaped CFST short column without ribs and with the optimal ribbing method are compared and analyzed. The results show that the optimal ribbing method involves setting half‐width longitudinal stiffening ribs in the middle of the two wide sides of the L‐shaped steel tube. The stiffening ribs can delay the occurrence of local buckling failure of the steel tube, thus strengthening the restraining effect of the steel tube on the concrete and improving the uniformity of the longitudinal stress of the core concrete. In addition, based on an analysis of a large number of parameters, four methods for calculating the bearing capacity of nonribbed L‐shaped CFST short columns are compared. A design formula for the bearing capacity of ribbed L‐shaped CFST columns is proposed by considering the improvement in the concrete performance. The calculation results agree well with the finite element and experimental results, and the error is <5%.