Laura Pérez-Martínez
Research Subjects
Laura Pérez-Martínez has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Alba Acevedo Fernández
HyGrInLab, National Renewable Energy Centre of Spain (CENER) Polígono Industrial Rocaforte
2 shared publications - Davide Cademartori
Department of Civil, Chemical and Environmental Engineering, University of Genoa (UNIGE-DICCA), Via all’Opera Pia 15, 16145 Genoa, Italy
2 shared publications - Iñigo Garbayo
National Renewable Energy Centre of Spain (CENER)
2 shared publications - Mónica Aguado
Public University of Navarre (UPNA)
2 shared publications - Paula Ciaurriz
National Renewable Energy Centre of Spain (CENER)
2 shared publications - Violeta Ureña-Torres
National Renewable Energy Centre of Spain (CENER)
2 shared publications
Latest Publications
- 28 October 2026
- Published by Elsevier in Electrochimica Acta
- Vol. 581
Advanced electrochemical characterization of button solid oxide cells by integrated DRT analyses and multi-physics modeling
- 28 October 2026
- Published by Elsevier in Electrochimica Acta
- Vol. 581
Advanced electrochemical characterization of button solid oxide cells by integrated DRT analyses and multi-physics modeling
- 23 October 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (20) , 204505
Successful Scale-Up of Solid Oxide Cell Manufacturing through Multilayer Water-Based Pre-Industrial Tape Casting
The scale-up of solid oxide cells (SOCs) manufacturing is critical for its industrial implementation. However, it presents significant challenges, including obtaining defect-free, dimensionally uniform layers and reproducible microstructure, controlling slurry properties, and minimizing resource consumption and waste generation. This work details the successful transition of a half-cell fabrication route (Ni-YSZ/YSZ) from laboratory scale to a pre-industrial roll-to-roll system, representing one of the first demonstrations of water-based multilayer casting at this scale. The scale-up was performed using water-based slurries as a feasible alternative to conventional organic-based systems, by carefully adjusting both slurry preparation and deposition parameters (i.e. gap, casting speed and drying temperature). While implementing pre-industrial fabrication, reduced slurry viscosity, sample reproducibility and appropriate microstructure were observed, resulting in maintained electrochemical performance (0.38 ± 0.02 and 0.42 ± 0.04 W cm −2 , using LSM-YSZ oxygen electrode). In addition, the optimized multilayer deposition resulted in fivefold increase in production capacity, from ∼ 30 to > 150 half-cells per week, as well as cost-efficient material utilization (from 3.5 to 0.7 € material cost per half-cell). These findings demonstrate the feasibility of high-throughput water-based SOCs manufacturing by a more sustainable process and offer a pathway toward the cost-effective production of next-generation energy technologies.
- 23 October 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (20) , 204505
Successful Scale-Up of Solid Oxide Cell Manufacturing through Multilayer Water-Based Pre-Industrial Tape Casting
The scale-up of solid oxide cells (SOCs) manufacturing is critical for its industrial implementation. However, it presents significant challenges, including obtaining defect-free, dimensionally uniform layers and reproducible microstructure, controlling slurry properties, and minimizing resource consumption and waste generation. This work details the successful transition of a half-cell fabrication route (Ni-YSZ/YSZ) from laboratory scale to a pre-industrial roll-to-roll system, representing one of the first demonstrations of water-based multilayer casting at this scale. The scale-up was performed using water-based slurries as a feasible alternative to conventional organic-based systems, by carefully adjusting both slurry preparation and deposition parameters (i.e. gap, casting speed and drying temperature). While implementing pre-industrial fabrication, reduced slurry viscosity, sample reproducibility and appropriate microstructure were observed, resulting in maintained electrochemical performance (0.38 ± 0.02 and 0.42 ± 0.04 W cm −2 , using LSM-YSZ oxygen electrode). In addition, the optimized multilayer deposition resulted in fivefold increase in production capacity, from ∼ 30 to > 150 half-cells per week, as well as cost-efficient material utilization (from 3.5 to 0.7 € material cost per half-cell). These findings demonstrate the feasibility of high-throughput water-based SOCs manufacturing by a more sustainable process and offer a pathway toward the cost-effective production of next-generation energy technologies.
- Open Access
- 1 March 2023
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 158 (9) , 094705
Kinetics of formic acid dehydration on Pt electrodes by time-resolved ATR-SEIRAS
The potential dependence of the rate of dehydration of formic acid to adsorbed CO (COad) on Pt at pH 1 has been studied on a polycrystalline Pt surface by time-resolved surface-enhanced infrared absorption spectroscopy in the attenuated total reflection mode (ATR-SEIRAS) with simultaneous recording of current transients after a potential step. A range of formic acid concentrations has been used to obtain a deeper insight into the mechanism of the reaction. Our experiments have allowed us to confirm that the potential dependence of the rate of dehydration has a bell shape, going through a maximum around the potential of zero total charge (pztc) of the most active site. The analysis of the integrated intensity and frequency of the bands corresponding to COL and COB/M shows a progressive population of the active sites on the surface. The observed potential dependence of the rate of formation of COad is consistent with a mechanism in which the reversible electroadsorption of HCOOad is followed by its rate-determining reduction to COad.
- 1 March 2023
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 158 (9) , 094705
Open AccessKinetics of formic acid dehydration on Pt electrodes by time-resolved ATR-SEIRAS
The potential dependence of the rate of dehydration of formic acid to adsorbed CO (COad) on Pt at pH 1 has been studied on a polycrystalline Pt surface by time-resolved surface-enhanced infrared absorption spectroscopy in the attenuated total reflection mode (ATR-SEIRAS) with simultaneous recording of current transients after a potential step. A range of formic acid concentrations has been used to obtain a deeper insight into the mechanism of the reaction. Our experiments have allowed us to confirm that the potential dependence of the rate of dehydration has a bell shape, going through a maximum around the potential of zero total charge (pztc) of the most active site. The analysis of the integrated intensity and frequency of the bands corresponding to COL and COB/M shows a progressive population of the active sites on the surface. The observed potential dependence of the rate of formation of COad is consistent with a mechanism in which the reversible electroadsorption of HCOOad is followed by its rate-determining reduction to COad.