Zhengtao Zhu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zhengtao Zhu has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Di Wang
Department of Mechanical Engineering, Xinjiang University, Urumqi 830017, China
3 shared publications - Fangping Ma
Department of Mechanical Engineering, Xinjiang University, Urumqi 830017, China
3 shared publications - Xiaoming Jin
Department of Mechanical Engineering, Xinjiang University, Urumqi 830017, China
3 shared publications
Latest Publications
- Open Access
- 26 March 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (7) , 2777
Numerical Analysis of the Wing Leading Edge Electro-Impulse De-Icing Process Based on Cohesive Zone Model
Aircraft icing has historically been a critical cause of airplane crashes. The electro-impulse de-icing system has a wide range of applications in aircraft de-icing due to its lightweight design, low energy consumption, high efficiency, and other advantages. However, there has been little study into accurate wing electric-impulse de-icing simulation methods and the parameters impacting de-icing efficacy. Based on the damage mechanics principle and considering the influence mechanisms of interface debonding and ice fracture on ice shedding, this paper establishes a more accurate numerical model of wing electric-impulse de-icing using the Cohesive Zone Model (CZM). It simulates the process of electric-impulse de-icing at the leading edge of the NACA 0012 wing. The numerical results are compared to the experimental results, revealing that the constructed wing electro-impulse de-icing numerical model is superior. Lastly, the effects of varying ice–skin interface shear adhesion strengths, doubler loading positions, and impulse sequences on de-icing effectiveness were studied. The de-icing rate is a quantitative description of the electro-impulse’s de-icing action, defined in the numerical model as the ratio of cohesive element deletions to the total elements at the ice–skin interface. The findings reveal that varying shear adhesion strengths at the ice–skin interface significantly impact the de-icing effect. The de-icing rate steadily falls with increasing shear adhesion strength, from 66% to 56%. When two, four, and seven impulses were applied to doubler two, the de-icing rates were 59%, 71%, and 71%, respectively, significantly increasing the de-icing efficiency compared to when impulses were applied to doubler one. Doubler one and two impulse responses are overlaid differently depending on the impulse sequences, resulting in varying de-icing rates. When the impulse sequence is 20 ms, the superposition results are optimal, and the de-icing rate reaches 100%. These studies can guide the development and implementation of a wing electric-impulse de-icing system.
- 26 March 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (7) , 2777
Open AccessNumerical Analysis of the Wing Leading Edge Electro-Impulse De-Icing Process Based on Cohesive Zone Model
Aircraft icing has historically been a critical cause of airplane crashes. The electro-impulse de-icing system has a wide range of applications in aircraft de-icing due to its lightweight design, low energy consumption, high efficiency, and other advantages. However, there has been little study into accurate wing electric-impulse de-icing simulation methods and the parameters impacting de-icing efficacy. Based on the damage mechanics principle and considering the influence mechanisms of interface debonding and ice fracture on ice shedding, this paper establishes a more accurate numerical model of wing electric-impulse de-icing using the Cohesive Zone Model (CZM). It simulates the process of electric-impulse de-icing at the leading edge of the NACA 0012 wing. The numerical results are compared to the experimental results, revealing that the constructed wing electro-impulse de-icing numerical model is superior. Lastly, the effects of varying ice–skin interface shear adhesion strengths, doubler loading positions, and impulse sequences on de-icing effectiveness were studied. The de-icing rate is a quantitative description of the electro-impulse’s de-icing action, defined in the numerical model as the ratio of cohesive element deletions to the total elements at the ice–skin interface. The findings reveal that varying shear adhesion strengths at the ice–skin interface significantly impact the de-icing effect. The de-icing rate steadily falls with increasing shear adhesion strength, from 66% to 56%. When two, four, and seven impulses were applied to doubler two, the de-icing rates were 59%, 71%, and 71%, respectively, significantly increasing the de-icing efficiency compared to when impulses were applied to doubler one. Doubler one and two impulse responses are overlaid differently depending on the impulse sequences, resulting in varying de-icing rates. When the impulse sequence is 20 ms, the superposition results are optimal, and the de-icing rate reaches 100%. These studies can guide the development and implementation of a wing electric-impulse de-icing system.
- Open Access
- 21 September 2023
- Published by MDPI AG in Agriculture
- Vol. 13 (9) , 1847
Simulation of Mouldboard Plough Soil Cutting Based on Smooth Particle Hydrodynamics Method and FEM–SPH Coupling Method
In the field of agricultural machinery, various empirical field tests are performed to measure the tillage force for precision tillage. However, the field test performance is costly and time-consuming, and there are many constraints on weather and field soil conditions; the utilization of simulation studies is required to overcome these shortcomings. As a result, the SPH method and the coupled FEM-SPH method are used in this paper to investigate the mouldboard plough–soil interaction. In this paper, the finite element software LS-DYNA was used to build the SPH model and the FEM-SPH coupling model of soil cutting, as well as to investigate the change in cutting resistance during the soil cutting process. The simulation results are compared with those of the experiments, and the curves of the simulation and experiment are in good agreement, which verifies the reliability of the model. The validated simulation model was used to investigate the effects of the cutting speed, depth of cut, inclination angle, and lifting angle of the mouldboard plough on cutting resistance. The simulation studies show that the SPH model takes 5 h and 2 min to compute, while the FEM-SPH coupled model takes 38 min; obviously, the computational efficiency of the FEM-SPH coupled model is higher. The relative errors between the SPH model and the experiment are 2.17% and 3.65%, respectively. The relative errors between the FEM-SPH coupled model and the experiment are 5.96% and 10.67%, respectively. Obviously, the SPH model has a higher computational accuracy. The average cutting resistances predicted by the SPH model and the FEM-SPH coupled model, respectively, were 349.48 N and 306.25 N; these resistances are useful for precision tillage. The cutting resistance increases with the increase in cutting speed and is quadratic; the cutting resistance increases with the increase in cutting depth and is quadratic; the horizontal cutting resistance and the combined cutting resistance increase with the increase in inclination angle, while the vertical cutting resistance remains essentially constant with the increase in inclination angle; the horizontal cutting resistance and combined cutting resistance increase as the lifting angle increases, while the vertical cutting resistance decreases as the lifting angle increases.
- 21 September 2023
- Published by MDPI AG in Agriculture
- Vol. 13 (9) , 1847
Open AccessSimulation of Mouldboard Plough Soil Cutting Based on Smooth Particle Hydrodynamics Method and FEM–SPH Coupling Method
In the field of agricultural machinery, various empirical field tests are performed to measure the tillage force for precision tillage. However, the field test performance is costly and time-consuming, and there are many constraints on weather and field soil conditions; the utilization of simulation studies is required to overcome these shortcomings. As a result, the SPH method and the coupled FEM-SPH method are used in this paper to investigate the mouldboard plough–soil interaction. In this paper, the finite element software LS-DYNA was used to build the SPH model and the FEM-SPH coupling model of soil cutting, as well as to investigate the change in cutting resistance during the soil cutting process. The simulation results are compared with those of the experiments, and the curves of the simulation and experiment are in good agreement, which verifies the reliability of the model. The validated simulation model was used to investigate the effects of the cutting speed, depth of cut, inclination angle, and lifting angle of the mouldboard plough on cutting resistance. The simulation studies show that the SPH model takes 5 h and 2 min to compute, while the FEM-SPH coupled model takes 38 min; obviously, the computational efficiency of the FEM-SPH coupled model is higher. The relative errors between the SPH model and the experiment are 2.17% and 3.65%, respectively. The relative errors between the FEM-SPH coupled model and the experiment are 5.96% and 10.67%, respectively. Obviously, the SPH model has a higher computational accuracy. The average cutting resistances predicted by the SPH model and the FEM-SPH coupled model, respectively, were 349.48 N and 306.25 N; these resistances are useful for precision tillage. The cutting resistance increases with the increase in cutting speed and is quadratic; the cutting resistance increases with the increase in cutting depth and is quadratic; the horizontal cutting resistance and the combined cutting resistance increase with the increase in inclination angle, while the vertical cutting resistance remains essentially constant with the increase in inclination angle; the horizontal cutting resistance and combined cutting resistance increase as the lifting angle increases, while the vertical cutting resistance decreases as the lifting angle increases.
- Open Access
- 8 September 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (18) , 13475
Analysis of Debonding Failures of the Screen and Case during Tablet Drop
In recent years, due to the increasingly powerful functions of tablets, more and more people have used tablets. The failure of the screen caused by debonding failure between the screen and the case of the tablet due to drops will affect the normal use of the tablet. However, there have been few studies on the debonding methods of the screen and the case of the tablet, as well as the factors influencing the debonding between the screen and the case of the tablet. Numerical analysis software was used in this paper to simulate the iPad Air (Air) drop process, and the cohesive zone model and tiebreak contact were used to simulate the debonding process between the screen and case of the Air tablet, respectively. When the results are compared to the experiments, the results show that the cohesive zone model is superior. The effects of various rounded corner radii, drop postures in the XY plane, materials of the outer case, and strain rates of PC/ABS on the localized debonding between the outer case and outer glass of the Air during the drop process were investigated. The degree of debonding between the Air model’s outer case and outer glass is defined by t, which is the ratio of the area of the deleted cohesive elements to the total area of the cohesive elements. The results show that the rounded corner radius and the strain rate of PC/ABS have less influence on t; the t of the Air model dropped at 45° in the XY plane is 37.7% of that dropped at 0° and 90°; and the t of the Air model with glass as the outer case material is 48% of that with aluminum alloy as the outer case material. These studies serve as a foundation for tablet design and material selection.
- 8 September 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (18) , 13475
Open AccessAnalysis of Debonding Failures of the Screen and Case during Tablet Drop
In recent years, due to the increasingly powerful functions of tablets, more and more people have used tablets. The failure of the screen caused by debonding failure between the screen and the case of the tablet due to drops will affect the normal use of the tablet. However, there have been few studies on the debonding methods of the screen and the case of the tablet, as well as the factors influencing the debonding between the screen and the case of the tablet. Numerical analysis software was used in this paper to simulate the iPad Air (Air) drop process, and the cohesive zone model and tiebreak contact were used to simulate the debonding process between the screen and case of the Air tablet, respectively. When the results are compared to the experiments, the results show that the cohesive zone model is superior. The effects of various rounded corner radii, drop postures in the XY plane, materials of the outer case, and strain rates of PC/ABS on the localized debonding between the outer case and outer glass of the Air during the drop process were investigated. The degree of debonding between the Air model’s outer case and outer glass is defined by t, which is the ratio of the area of the deleted cohesive elements to the total area of the cohesive elements. The results show that the rounded corner radius and the strain rate of PC/ABS have less influence on t; the t of the Air model dropped at 45° in the XY plane is 37.7% of that dropped at 0° and 90°; and the t of the Air model with glass as the outer case material is 48% of that with aluminum alloy as the outer case material. These studies serve as a foundation for tablet design and material selection.