Malgorzata Kmiotek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Malgorzata Kmiotek has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Adrian Kordos
Rzeszow Univ Technol, Fac Mech Engn & Aeronaut, Dept Aerosp Engn, Al Powstancow Warszawy 12, PL-35959 Rzeszow, Poland
3 shared publications - Adam Piszczatowski
Rzeszow Univ Technol, Fac Mech Engn & Aeronaut, Al Powstancow Warszawy 12, PL-35629 Rzeszow, Poland
2 shared publications - Adam Zaremba
Rzeszow Univ Technol, Fac Mech Engn & Aeronaut, Al Powstancow Warszawy 12, PL-35629 Rzeszow, Poland
2 shared publications Robert Smusz
Rzeszow University of Technology, The Faculty of Mechanical Engineering and Aeronautics, Rzeszow, Poland
1 shared publication- Tomasz Muszyński
Institute of Technical Sciences and Aviation, The State School of Higher Education in Chelm
1 shared publication - Wojciech Żyłka
Faculty of Exact and Technical Sciences, Institute of Materials Engineering, University of Rzeszow, Pigonia 1, 35-310 Rzeszow, Poland
1 shared publication
Latest Publications
- Open Access
- 1 June 2026
- Published by WNGB Scientific Publishing House Sp. z o.o. in Advances in Science and Technology Research Journal
- Vol. 20 (6) , 93-106
Modeling of the front wing cross-section for a formula student vehicle
The aim of this article was to design an optimal cross-section of the front wing for a Formula Student vehicle, conducted in compliance with applicable technical and aerodynamic regulations. The article focuses on analyzing various configurations of four-element wings supported by Computational...
- 1 June 2026
- Published by WNGB Scientific Publishing House Sp. z o.o. in Advances in Science and Technology Research Journal
- Vol. 20 (6) , 93-106
Open AccessModeling of the front wing cross-section for a formula student vehicle
The aim of this article was to design an optimal cross-section of the front wing for a Formula Student vehicle, conducted in compliance with applicable technical and aerodynamic regulations. The article focuses on analyzing various configurations of four-element wings supported by Computational...
- Open Access
- 1 November 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 18 (7) , 277-288
The Problem of Recycling of Unmanned Aerial Vehicles
Recently an extensive growth in the market for Unmanned Aerial Vehicles (UAVs, drones) has been observed. Because of numerous advantages, their application in various areas is wide, starting with military, through civilian – specialized up to amateur. The world market for civilian commercial...
- 1 November 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 18 (7) , 277-288
Open AccessThe Problem of Recycling of Unmanned Aerial Vehicles
Recently an extensive growth in the market for Unmanned Aerial Vehicles (UAVs, drones) has been observed. Because of numerous advantages, their application in various areas is wide, starting with military, through civilian – specialized up to amateur. The world market for civilian commercial...
- 23 December 2023
- Published by Polish Academy of Sciences Chancellery in Archive of Mechanical Engineering
- Vol. 70 (4) , 553-566
Effect of thin obstacles heights on heat transfer and flow characteristics in microchannels
This paper presents a numerical analysis of the thermal-flow characteristics for a laminar flow inside a rectangular microchannel. The flow of water through channels with thin obstacles mounted on opposite walls was analyzed. The studies were conducted with a low Reynolds number (from 20 to 200). Different heights of rectangular obstacles were analyzed to see if geometrical factors influence fluid flow and heat exchange in the microchannel. Despite of the fact that the use of thin obstacles in the microchannels leads to an increase in the pressure drop, the increase in the height of the obstacles favors a significant intensification of heat exchange with the maximum thermal gain factor of 1.9 for the obstacle height coefficient h/H=0.5, which could be acceptable for practical application.
- 23 December 2023
- Published by Polish Academy of Sciences Chancellery in Archive of Mechanical Engineering
- Vol. 70 (4) , 553-566
Effect of thin obstacles heights on heat transfer and flow characteristics in microchannels
This paper presents a numerical analysis of the thermal-flow characteristics for a laminar flow inside a rectangular microchannel. The flow of water through channels with thin obstacles mounted on opposite walls was analyzed. The studies were conducted with a low Reynolds number (from 20 to 200). Different heights of rectangular obstacles were analyzed to see if geometrical factors influence fluid flow and heat exchange in the microchannel. Despite of the fact that the use of thin obstacles in the microchannels leads to an increase in the pressure drop, the increase in the height of the obstacles favors a significant intensification of heat exchange with the maximum thermal gain factor of 1.9 for the obstacle height coefficient h/H=0.5, which could be acceptable for practical application.
- Open Access
- 20 October 2023
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 17 (5) , 248-259
Numerical Study of the Effect of the Trailing-Edge Devices (Gurney Flap and Divergent Trailing-edge Flap) on the Aerodynamic Characteristics of an Airfoil in Transonic Flow for Drone Applications
The aim of this study was to investigate the effects of mini Trailing-Edge Devices (mini TEDs) on the aerodynamic characteristics of the RAE 2822 airfoil. Using ANSYS Fluent software, numerical simulations were conducted to analyze the compressible flow around the airfoil at Mach number (Ma)...
- 20 October 2023
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 17 (5) , 248-259
Open AccessNumerical Study of the Effect of the Trailing-Edge Devices (Gurney Flap and Divergent Trailing-edge Flap) on the Aerodynamic Characteristics of an Airfoil in Transonic Flow for Drone Applications
The aim of this study was to investigate the effects of mini Trailing-Edge Devices (mini TEDs) on the aerodynamic characteristics of the RAE 2822 airfoil. Using ANSYS Fluent software, numerical simulations were conducted to analyze the compressible flow around the airfoil at Mach number (Ma)...