V. Merta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
V. Merta has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Filip Radkovský
VSB - Technical University of Ostrava, Czech Republic
2 shared publications - Petr Lichý
VSB - Technical University of Ostrava, Czech Republic
2 shared publications T. Obzina
VSB - Technical University of Ostrava, Czech Republic
2 shared publications- Ivana Kroupová
Department of Metallurgical Technologies, Faculty of Materials Science and Technology, VSB-Technical University of Ostrava, 17. Listopadu 2172/15, 708 00 Ostrava, Czech Republic
1 shared publication J. Rygel
VSB - Technical University of Ostrava, Czech Republic
1 shared publication- Jan Jezierski
Silesian University of Technology, Department of Foundry Engineering, Towarowa 7, 44-100 Gliwice, Poland
1 shared publication
Latest Publications
- 6 June 2023
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 68 (2) , 757-763
Technology of Production of Mold Filling Material for Specific Purposes in the Field of Metallic Foam Casting
This paper describes the technology for the production of precursors (space holder material) used to form the complex internal structure of cast metal foam. The precursor material must exhibit sufficient refractoriness, resist contact with liquid metal and at the same time should exhibit good collapsibility after casting. With regard to the greening of foundry production, the focus of this paper was on materials that could exhibit the above properties and at the same time do not have a negative impact on the environment. In this paper, the technology for the production of spherical precursors from a self-hardening mixture with a geopolymer-based binder system is described and verified. The motivation for the choice of material and all the sub-steps of the process – molding into the core box, tumbling, including the necessary accompanying tests of the mechanical properties of the core mixture being verified – are described.
- 6 June 2023
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 68 (2) , 757-763
Technology of Production of Mold Filling Material for Specific Purposes in the Field of Metallic Foam Casting
This paper describes the technology for the production of precursors (space holder material) used to form the complex internal structure of cast metal foam. The precursor material must exhibit sufficient refractoriness, resist contact with liquid metal and at the same time should exhibit good collapsibility after casting. With regard to the greening of foundry production, the focus of this paper was on materials that could exhibit the above properties and at the same time do not have a negative impact on the environment. In this paper, the technology for the production of spherical precursors from a self-hardening mixture with a geopolymer-based binder system is described and verified. The motivation for the choice of material and all the sub-steps of the process – molding into the core box, tumbling, including the necessary accompanying tests of the mechanical properties of the core mixture being verified – are described.
- 8 March 2022
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 22 (1) , 48-52
Evaluation of Collapsibility of Selected Core Systems
There are mainly two different ways of producing sand cores in the industry. The most used is the shooting moulding process. A mixture of sand and binder is injected by compressed air into a cavity (core), where it is then thermally or chemically cured. Another relatively new method of manufacturing cores is the use of 3D printing. The principle is based on the method of local curing of the sand bed. The ability to destroy sand cores after casting can be evaluated by means of tests that are carried out directly on the test core. In most cases, the core is thermally degraded and the mechanical properties before and after thermal exposure are measured. Another possible way to determine the collapsibility of core mixtures can be performed on test castings, where a specific casting is designed for different binder systems. The residual strength is measured by subsequent shake-out or knock-out tests. In this paper, attention will be paid to the collapsibility of core mixtures in aluminium castings.
- 8 March 2022
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 22 (1) , 48-52
Evaluation of Collapsibility of Selected Core Systems
There are mainly two different ways of producing sand cores in the industry. The most used is the shooting moulding process. A mixture of sand and binder is injected by compressed air into a cavity (core), where it is then thermally or chemically cured. Another relatively new method of manufacturing cores is the use of 3D printing. The principle is based on the method of local curing of the sand bed. The ability to destroy sand cores after casting can be evaluated by means of tests that are carried out directly on the test core. In most cases, the core is thermally degraded and the mechanical properties before and after thermal exposure are measured. Another possible way to determine the collapsibility of core mixtures can be performed on test castings, where a specific casting is designed for different binder systems. The residual strength is measured by subsequent shake-out or knock-out tests. In this paper, attention will be paid to the collapsibility of core mixtures in aluminium castings.
- 1 January 2021
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 21 (1) , 125-131
Design of Proven Technology of Metal Foam and Porous Metal Casting Production
- 1 January 2021
- Published by Polish Academy of Sciences Chancellery in Archives of Foundry Engineering
- Vol. 21 (1) , 125-131
Design of Proven Technology of Metal Foam and Porous Metal Casting Production