Yan Qiao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yan Qiao has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Wei Long
Faculty of Mechanical and Electrical Engineering Kunming University of Science and Technology Kunming China
3 shared publications Yusen Zhang
2 shared publications- Bin Li
Faculty of Environmental Science and Engineering, Kunming University of Science and Technology, Kunming, 650500, China
1 shared publication Haifeng Qian
Faculty of Mechanical and Electrical Engineering, Kunming University of Science and Technology, Kunming, People’s Republic of China
1 shared publicationPengyang Wang
Kunming Univ Sci & Technol, Fac Mech & Elect Engn, Kunming 650500, Peoples R China
1 shared publicationPuteng Gui
Kunming Univ Sci & Technol, Fac Mech & Elect Engn, Kunming 650500, Peoples R China
1 shared publication
Latest Publications
- 21 May 2025
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 13 (2) , 025010
Effect of fishbone variable-depth surface texturing on the friction and wear performance of silicon carbide under water lubrications
Surface textures significantly improve the tribological properties of friction pairs by optimising the selection of texture types and structural parameters, thereby enhancing antiwear and friction-reducing performance. In this study, to enhance the tribological performance of silicon carbide (SiC) planar friction pairs, a fishbone variable-depth reticular texture was developed through the computational fluid dynamics (CFD) optimisation of a cross-reticular texture. Its lubrication and friction-reducing capabilities were then validated via tribological experiments, and advanced characterisation techniques were used to elucidate its underlying mechanisms. Experimental results demonstrate that the fishbone texture significantly lowers the interfacial coefficient of friction (COF) during counterclockwise rotation, especially at speeds exceeding 1200 rpm, where the COF drops below 0.01, achieving superlubricity. Frictional heat tests indicate that the fishbone texture effectively mitigates the temperature rise in friction pairs. Interfacial frictional electric tests reveal that the fishbone texture enhances the interfacial polarisation electric field, thereby improving the adsorption capacity of lubricant films and increasing the electric field repulsion between friction pairs. The lubrication and friction-reducing mechanisms of the fishbone texture are governed by four synergistic effects: the variable-depth area of the pressurisation unit enhances the hydrodynamic effect; the wedge area induces a secondary throttling effect; a shear-easy silicon-based friction film forms during interfacial friction; and the polarisation electric field generated by the solid–liquid–solid interfacial friction creates repulsive forces. This study presents a novel strategy for improving the lubrication and friction-reducing performance of high-speed, heavy-load bearings, providing significant theoretical and practical contributions.
- 21 May 2025
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 13 (2) , 025010
Effect of fishbone variable-depth surface texturing on the friction and wear performance of silicon carbide under water lubrications
Surface textures significantly improve the tribological properties of friction pairs by optimising the selection of texture types and structural parameters, thereby enhancing antiwear and friction-reducing performance. In this study, to enhance the tribological performance of silicon carbide (SiC) planar friction pairs, a fishbone variable-depth reticular texture was developed through the computational fluid dynamics (CFD) optimisation of a cross-reticular texture. Its lubrication and friction-reducing capabilities were then validated via tribological experiments, and advanced characterisation techniques were used to elucidate its underlying mechanisms. Experimental results demonstrate that the fishbone texture significantly lowers the interfacial coefficient of friction (COF) during counterclockwise rotation, especially at speeds exceeding 1200 rpm, where the COF drops below 0.01, achieving superlubricity. Frictional heat tests indicate that the fishbone texture effectively mitigates the temperature rise in friction pairs. Interfacial frictional electric tests reveal that the fishbone texture enhances the interfacial polarisation electric field, thereby improving the adsorption capacity of lubricant films and increasing the electric field repulsion between friction pairs. The lubrication and friction-reducing mechanisms of the fishbone texture are governed by four synergistic effects: the variable-depth area of the pressurisation unit enhances the hydrodynamic effect; the wedge area induces a secondary throttling effect; a shear-easy silicon-based friction film forms during interfacial friction; and the polarisation electric field generated by the solid–liquid–solid interfacial friction creates repulsive forces. This study presents a novel strategy for improving the lubrication and friction-reducing performance of high-speed, heavy-load bearings, providing significant theoretical and practical contributions.
- 18 November 2024
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 12 (4) , 045013
Effect of bionic shield texture on friction behavior of silicon carbide under water lubrication condition
Reasonable texture parameters can effectively generate local dynamic pressure effects and promote the formation of lubrication film. The synergistic friction reduction mechanism of the shield-shaped texture on the Silicon Carbide (SiC) surface under water-based lubrication conditions between the flow pressure effect and the ‘rolling ball’ effect is investigated by combining simulation analysis and friction experiments. The effects of shield textured surface on the friction and wear characteristics of SiC surface and the characteristics of interfacial polarization electric field under different rotational speeds and different load conditions were analyzed. The results display that synergistic texture lubrication has a beneficial effect on improving tribological properties. The surface with 6% texture area occupancy showed the best tribological characteristics. The surface with a textured area occupancy of 6% displays the optimal tribological properties. Moreover, the friction reduction mechanisms under different working conditions are discussed, with the textured uniformly arranged surfaces being more suitable for high-speed and heavy load (140 N, 2000 rpm) conditions and the textured non-uniformly arranged surfaces being more suitable for low-speed and light load (40 N, 400 rpm) conditions.
- 18 November 2024
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 12 (4) , 045013
Effect of bionic shield texture on friction behavior of silicon carbide under water lubrication condition
Reasonable texture parameters can effectively generate local dynamic pressure effects and promote the formation of lubrication film. The synergistic friction reduction mechanism of the shield-shaped texture on the Silicon Carbide (SiC) surface under water-based lubrication conditions between the flow pressure effect and the ‘rolling ball’ effect is investigated by combining simulation analysis and friction experiments. The effects of shield textured surface on the friction and wear characteristics of SiC surface and the characteristics of interfacial polarization electric field under different rotational speeds and different load conditions were analyzed. The results display that synergistic texture lubrication has a beneficial effect on improving tribological properties. The surface with 6% texture area occupancy showed the best tribological characteristics. The surface with a textured area occupancy of 6% displays the optimal tribological properties. Moreover, the friction reduction mechanisms under different working conditions are discussed, with the textured uniformly arranged surfaces being more suitable for high-speed and heavy load (140 N, 2000 rpm) conditions and the textured non-uniformly arranged surfaces being more suitable for low-speed and light load (40 N, 400 rpm) conditions.