Ivan Panchenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ivan Panchenko has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Nikita Shandyba
Southern Federal University, Institute of Nanotechnologies, Electronics, and Equipment Engineering, Taganrog, 347922, Russia
3 shared publications - Alexey Kolomiytsev
Southern Federal University, Institute of Nanotechnologies, Electronics and Equipment Engineering, 2 Shevchenko st, Taganrog 347922, Russia
2 shared publications Alexandr Gromov
1 shared publication- Evgeny Zamburg
Department of Electrical and Computer Engineering, National University of Singapore, Singapore, Singapore
1 shared publication M I Pelipenko
UAC company BERIEV, Taganrog, 347923, Russia
1 shared publication- Oleg Alekseevich Ageev
Institute of Nanotechnologies, Electronics and Electronic Equipment Engineering, Southern Federal University, 347922 Taganrog, Russia
1 shared publication
Latest Publications
- 15 January 2019
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2064 (1) , 030011
Investigation of the local profiling of the solid surfaces using focused ion beam
In this paper, we present the results of an experimental study of the processes of local profiling of a material surface by a focused ion beam. The regularities of the influence of the main technological parameters of etching by the FIB method on the surface roughness of the substrate were established experimentally. It was revealed that the main factors affecting the formation of the surface relief of a solid when etched by a focused ion beam are: FIB overlap, the beam dwell time, and the ion beam current. It is shown that when the overlap is about 30-50%, the substrate roughness is minimal, and the FIB current and the beam dwell do not exert a determining influence on the roughness. The obtained results can be used to develop technological processes for the fabrication of the structures and elements for micro- and nanoelectronics.
- 15 January 2019
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2064 (1) , 030011
Investigation of the local profiling of the solid surfaces using focused ion beam
In this paper, we present the results of an experimental study of the processes of local profiling of a material surface by a focused ion beam. The regularities of the influence of the main technological parameters of etching by the FIB method on the surface roughness of the substrate were established experimentally. It was revealed that the main factors affecting the formation of the surface relief of a solid when etched by a focused ion beam are: FIB overlap, the beam dwell time, and the ion beam current. It is shown that when the overlap is about 30-50%, the substrate roughness is minimal, and the FIB current and the beam dwell do not exert a determining influence on the roughness. The obtained results can be used to develop technological processes for the fabrication of the structures and elements for micro- and nanoelectronics.
- Open Access
- 21 December 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1124 (8) , 081036
Size effect on memristive properties of nanocrystalline ZnO film for resistive synaptic devices
Size effect on memristive properties of nanocrystalline ZnO film was investigated. It was shown, ZnO film thickness increase from 6.23±1.54 nm to 47.60±8.12 nm leads to high-resistance state (HRS) increase from 3.26±2.14 MΩ to 700.32±300.83 MΩ and low-resistance state (LRS) from 0.03±0.02 MΩ to 0.09±0.03 MΩ, respectively. The HRS/LRS ratio increases from 108 to 7742. The results can be useful for based on nanocrystalline ZnO films resistive synaptic devices manufacturing.
- 21 December 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1124 (8) , 081036
Open AccessSize effect on memristive properties of nanocrystalline ZnO film for resistive synaptic devices
Size effect on memristive properties of nanocrystalline ZnO film was investigated. It was shown, ZnO film thickness increase from 6.23±1.54 nm to 47.60±8.12 nm leads to high-resistance state (HRS) increase from 3.26±2.14 MΩ to 700.32±300.83 MΩ and low-resistance state (LRS) from 0.03±0.02 MΩ to 0.09±0.03 MΩ, respectively. The HRS/LRS ratio increases from 108 to 7742. The results can be useful for based on nanocrystalline ZnO films resistive synaptic devices manufacturing.
- Open Access
- 14 November 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 443 (1) , 012015
Fabrication of probes for scanning near-field optical microscopy using focused ion beam
The results of an experimental study of the fabrication of probe tips for scanning near-field optical microscopy (SNOM) using the focused ion beam (FIB) milling and ion beam induced deposition are presented. Methods of the FIB local milling and FIB-induced deposition of tungsten and carbon onto the tip of an atomic force microscope (AFM) probe are studied. In this work, a technique for the formation of AFM probes based on the use of a combination of ion-beam etching and ion-induced carbon deposition was developed. Based on the developed technique, several aperture probes for SNOM with an aperture diameter of 50, 150, and 200 nm, an apex height of about 20 nm, and a cone angle of about 35° were fabricated. The paper presents that the formation of SNOM probes by FIB-induced deposition allows creating a high efficiency tool for nanodiagnostics. The obtained results can be used to develop technological processes for the fabrication of specialized AFM probes and procedures for the express monitoring of technological process parameters in the manufacturing of the elements for micro- and nanoelectronics.
- 14 November 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 443 (1) , 012015
Open AccessFabrication of probes for scanning near-field optical microscopy using focused ion beam
The results of an experimental study of the fabrication of probe tips for scanning near-field optical microscopy (SNOM) using the focused ion beam (FIB) milling and ion beam induced deposition are presented. Methods of the FIB local milling and FIB-induced deposition of tungsten and carbon onto the tip of an atomic force microscope (AFM) probe are studied. In this work, a technique for the formation of AFM probes based on the use of a combination of ion-beam etching and ion-induced carbon deposition was developed. Based on the developed technique, several aperture probes for SNOM with an aperture diameter of 50, 150, and 200 nm, an apex height of about 20 nm, and a cone angle of about 35° were fabricated. The paper presents that the formation of SNOM probes by FIB-induced deposition allows creating a high efficiency tool for nanodiagnostics. The obtained results can be used to develop technological processes for the fabrication of specialized AFM probes and procedures for the express monitoring of technological process parameters in the manufacturing of the elements for micro- and nanoelectronics.