Yingzheng Bai
Research Subjects
Yingzheng Bai has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Guangwen Liu
2 shared publicationsJingyue Luan
2 shared publicationsLing Xu
2 shared publicationsQingxia Sun
2 shared publicationsShuyuan Zhu
2 shared publicationsYijie Zhang
2 shared publications
Latest Publications
- Open Access
- 1 April 2026
- Published by Elsevier in SSRN Electronic Journal
Development of Single-Fluid Synchronous Grouting Material Based on High-Content Clayey Spoil from Shield Tunneling: Characterization of Mechanical Properties, Rheological Behavior, and Microstructure
The efficient utilization of clayey spoil from shield tunneling poses a key challenge for sustainable infrastructure development. This study developed a high-volume spoil-based single-fluid synchronous grouting material using spoil from Jinan Metro Line 9. The effects of spoil content (60 ~ 90wt%), water-to-solid ratio (0.55~0.70), cement/fly ash ratio, and composite admixtures (viscosity-modifying agent, defoamer, accelerator) on the mechanical properties, rheology, and microstructure of the grout were systematically investigated. The optimal formulation (spoil: cement: fly ash = 6:3:1, water-to-solid ratio = 0.55) incorporating 1‰ viscosity-reducing agent(VRA) A, 3‰ VRA B, 4‰ defoamer, 3% calcium formate, and 1% sodium aluminate exhibited a 28‑day compressive strength of 3.19 MPa, a flow diameter of 251 mm, and a setting time of 10.55 h, meeting the requirements of the T/CECS 563‑2018 standard. Microstructural analyses (SEM, XRD) revealed that a low water-to-solid ratio (≤0.6) promotes cement hydration and fly ash pozzolanic reaction, forming an interwoven network of ettringite and C‑S‑H gel that significantly reduces porosity. Spoil content exceeding 80% increased water demand, leading to a 20~30% reduction in strength. The admixtures exhibited synergistic effects: viscosity-modifying agents enhanced particle dispersion, defoamer minimized air voids, and the combined accelerator promoted ettringite formation and shortened the setting time to 6.2 h. This work provides an environmentally viable solution for large‑scale recycling of shield spoil into high‑performance grouting materials.
- 1 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDevelopment of Single-Fluid Synchronous Grouting Material Based on High-Content Clayey Spoil from Shield Tunneling: Characterization of Mechanical Properties, Rheological Behavior, and Microstructure
The efficient utilization of clayey spoil from shield tunneling poses a key challenge for sustainable infrastructure development. This study developed a high-volume spoil-based single-fluid synchronous grouting material using spoil from Jinan Metro Line 9. The effects of spoil content (60 ~ 90wt%), water-to-solid ratio (0.55~0.70), cement/fly ash ratio, and composite admixtures (viscosity-modifying agent, defoamer, accelerator) on the mechanical properties, rheology, and microstructure of the grout were systematically investigated. The optimal formulation (spoil: cement: fly ash = 6:3:1, water-to-solid ratio = 0.55) incorporating 1‰ viscosity-reducing agent(VRA) A, 3‰ VRA B, 4‰ defoamer, 3% calcium formate, and 1% sodium aluminate exhibited a 28‑day compressive strength of 3.19 MPa, a flow diameter of 251 mm, and a setting time of 10.55 h, meeting the requirements of the T/CECS 563‑2018 standard. Microstructural analyses (SEM, XRD) revealed that a low water-to-solid ratio (≤0.6) promotes cement hydration and fly ash pozzolanic reaction, forming an interwoven network of ettringite and C‑S‑H gel that significantly reduces porosity. Spoil content exceeding 80% increased water demand, leading to a 20~30% reduction in strength. The admixtures exhibited synergistic effects: viscosity-modifying agents enhanced particle dispersion, defoamer minimized air voids, and the combined accelerator promoted ettringite formation and shortened the setting time to 6.2 h. This work provides an environmentally viable solution for large‑scale recycling of shield spoil into high‑performance grouting materials.