Athira P
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Athira P has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Koustuv Ray
IIT Kharagpur
4 shared publications - Sunil Kumar Sahoo
Department of Chemical Engineering
2 shared publications - Alexander Zirn
Institute of Chemical Engineering Ulm University Ulm Germany
1 shared publication Gnanasekaran G
Department of Chemical Engineering
1 shared publication- Göran Baade
Institute of Chemical Engineering Ulm University Ulm Germany
1 shared publication - Hannes Stagge
Universität Ulm
1 shared publication
Latest Publications
- Open Access
- 14 May 2026
- Published by Wiley in ChemCatChem
- Vol. 18 (9)
Extending the Periodic Transient Kinetics Method by a Combination of Spectroscopic Techniques and Microkinetic Modeling
Transient experimentation is broadly applied in heterogeneous catalysis as insights into surface dynamics can be retrieved. However, the nature and activity of the involved surface intermediates remain uncertain, impeding clear mechanistic conclusions. Thus, in this work, we extend transient experimentation with microkinetic modeling and spectroscopic techniques. In this study, CO 2 methanation experiments were performed on a supported catalyst (Ru/TiO 2 ) using the Periodic Transient Kinetics (PTK) method. Elemental balances based on the transient results showed decoupled hydrogenation pathways and storage behavior for surface carbon and oxygen species. The nature of these species was elucidated by Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS) studies providing evidence for support‐bound species. Potential lumped mechanisms were formulated discriminating between species adsorbed on the support or active material. On the basis of these mechanisms, microkinetic models were set up, fitted to the experimental data and compared by their deviation to the transient experimental data. By comparing the steady‐state coverage of the simulated surface to the spectroscopic results, plausibility was checked. We show that DRIFTS, PTK, and microkinetic modeling provide complementary data in a way that quantitative mechanistic information can be obtained. This synergy is only possible using dynamic experimentation.
- 14 May 2026
- Published by Wiley in ChemCatChem
- Vol. 18 (9)
Open AccessExtending the Periodic Transient Kinetics Method by a Combination of Spectroscopic Techniques and Microkinetic Modeling
Transient experimentation is broadly applied in heterogeneous catalysis as insights into surface dynamics can be retrieved. However, the nature and activity of the involved surface intermediates remain uncertain, impeding clear mechanistic conclusions. Thus, in this work, we extend transient experimentation with microkinetic modeling and spectroscopic techniques. In this study, CO 2 methanation experiments were performed on a supported catalyst (Ru/TiO 2 ) using the Periodic Transient Kinetics (PTK) method. Elemental balances based on the transient results showed decoupled hydrogenation pathways and storage behavior for surface carbon and oxygen species. The nature of these species was elucidated by Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS) studies providing evidence for support‐bound species. Potential lumped mechanisms were formulated discriminating between species adsorbed on the support or active material. On the basis of these mechanisms, microkinetic models were set up, fitted to the experimental data and compared by their deviation to the transient experimental data. By comparing the steady‐state coverage of the simulated surface to the spectroscopic results, plausibility was checked. We show that DRIFTS, PTK, and microkinetic modeling provide complementary data in a way that quantitative mechanistic information can be obtained. This synergy is only possible using dynamic experimentation.
- 6 January 2026
- Published by Wiley in European Journal of Inorganic Chemistry
- Vol. 29 (8)
Rh and Ni–Fe Alloy Catalysts Supported on γ ‐Al 2 O 3 for CO 2 Methanation: A Combined Kinetic and DRIFTS Study
Catalytic CO 2 methanation offers a promising pathway for converting captured CO 2 and renewable H 2 into synthetic methane. This study presents a comparative investigation of γ ‐Al 2 O 3 ‐supported Ni–Fe alloy and Rh catalysts under identical reaction conditions, integrating parametric evaluation, power‐law kinetic modeling, and in situ DRIFTS. The optimum conditions identified as 623 K, CO 2 :H 2 :Ar = 1:6:3, and GHSV = 60 000 mL h −1 gcat −1 , where 75Ni25Fe showed higher CO 2 conversion, while 100Rh achieved nearly 100% CH 4 selectivity. Both catalysts showed stable performance over 12 h of continuous operation. Kinetic analysis revealed the positive and fractional apparent reaction orders for both CO 2 and H 2 (for 75Ni25Fe, α = 0.28 ± 0.09, and β = 0.34 ± 0.07, whereas for 100Rh, = 0.22 ± 0.06, and β = 0.56 ± 0.05), indicating nonlinear rate dependence on reactant's partial pressures. The apparent activation energy was lower for 100Rh (96 kJ mol −1 ) compared to 75Ni25Fe (114 kJ mol −1 ), reflecting its higher intrinsic activity. In situ DRIFTS revealed distinct mechanistic pathways: Ni–Fe alloy catalyst follows a formate‐mediated route, while the Rh catalyst favors RWGS followed by the CO methanation route. Overall, Rh serves as a benchmark for CH 4 selectivity, while Ni–Fe offers a cost‐effective alternative for CO 2 methanation.
- 6 January 2026
- Published by Wiley in European Journal of Inorganic Chemistry
- Vol. 29 (8)
Rh and Ni–Fe Alloy Catalysts Supported on γ ‐Al 2 O 3 for CO 2 Methanation: A Combined Kinetic and DRIFTS Study
Catalytic CO 2 methanation offers a promising pathway for converting captured CO 2 and renewable H 2 into synthetic methane. This study presents a comparative investigation of γ ‐Al 2 O 3 ‐supported Ni–Fe alloy and Rh catalysts under identical reaction conditions, integrating parametric evaluation, power‐law kinetic modeling, and in situ DRIFTS. The optimum conditions identified as 623 K, CO 2 :H 2 :Ar = 1:6:3, and GHSV = 60 000 mL h −1 gcat −1 , where 75Ni25Fe showed higher CO 2 conversion, while 100Rh achieved nearly 100% CH 4 selectivity. Both catalysts showed stable performance over 12 h of continuous operation. Kinetic analysis revealed the positive and fractional apparent reaction orders for both CO 2 and H 2 (for 75Ni25Fe, α = 0.28 ± 0.09, and β = 0.34 ± 0.07, whereas for 100Rh, = 0.22 ± 0.06, and β = 0.56 ± 0.05), indicating nonlinear rate dependence on reactant's partial pressures. The apparent activation energy was lower for 100Rh (96 kJ mol −1 ) compared to 75Ni25Fe (114 kJ mol −1 ), reflecting its higher intrinsic activity. In situ DRIFTS revealed distinct mechanistic pathways: Ni–Fe alloy catalyst follows a formate‐mediated route, while the Rh catalyst favors RWGS followed by the CO methanation route. Overall, Rh serves as a benchmark for CH 4 selectivity, while Ni–Fe offers a cost‐effective alternative for CO 2 methanation.
- 15 October 2025
- Published by Elsevier in Molecular Catalysis
- Vol. 588
Effect of iron, cobalt and copper in nickel-based bimetal catalysts for CO2 activation - Insights from DFT and DRIFTS
- 15 October 2025
- Published by Elsevier in Molecular Catalysis
- Vol. 588
Effect of iron, cobalt and copper in nickel-based bimetal catalysts for CO2 activation - Insights from DFT and DRIFTS