Alexander A. Marmalyuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Alexander A. Marmalyuk has a total of 76 co-authors. Here are the top co-authors by number of shared publications:
- Timur A. Bagaev
AO Stel’makh Polyus Research Institute
6 shared publications M. A. Ladugin
Polyus’ Research Institute of M.F. Stelmakh Joint Stock Company, Moscow, Russia
5 shared publications- Nikita A. Pikhtin
Ioffe Institute
5 shared publications - Sergey Olegovich Slipchenko
Ioffe Institute
5 shared publications A. A. Padalitsa
JSC Sigm Plus, Moscow, Russia
3 shared publications- Aleksandr A. Podoskin
Ioffe Institute, St. Petersburg, Russia
3 shared publications
Latest Publications
- Open Access
- 16 December 2025
- Published by National University of Science and Technology MISiS in Materials of Electronics Engineering
Effect of nickel electroplating conditions on the strength of Cu/Ni/Au|AuSn solder joints in the fabrication of high-power semiconductor emitters
The dependence of the strength of a Cu/Ni/Au|AuSn solder joint on the conditions of the galvanic deposition process for the nickel barrier layer is studied. It is shown that when using a succinic acid-based electrolyte, the introduction of poorly soluble nickel succinate into the deposited layer can reduce the strength of the solder joint. The key factor controlling the occurrence of this undesirable process is the pH of the electrolyte. This paper attempts to reconstruct the relationship between solder joint strength and the conditions for the formation of a galvanic Ni barrier layer. Graphs of the peel force versus the pH of the nickel plating electrolyte, changes in electrolyte pH depending on the number of parts processed, and calculated equilibrium concentrations of nickel complexes in the electrolyte that affect the quality of the resulting coating are presented. Using mathematical modeling, an attempt was made to predict the redistribution of nickel complexes when adjusting the electrolyte composition and pH using various methods. The calculated strength results were compared with those obtained in practice. Approaches to mitigating the negative effect of nickel succinate are proposed.
- 16 December 2025
- Published by National University of Science and Technology MISiS in Materials of Electronics Engineering
Open AccessEffect of nickel electroplating conditions on the strength of Cu/Ni/Au|AuSn solder joints in the fabrication of high-power semiconductor emitters
The dependence of the strength of a Cu/Ni/Au|AuSn solder joint on the conditions of the galvanic deposition process for the nickel barrier layer is studied. It is shown that when using a succinic acid-based electrolyte, the introduction of poorly soluble nickel succinate into the deposited layer can reduce the strength of the solder joint. The key factor controlling the occurrence of this undesirable process is the pH of the electrolyte. This paper attempts to reconstruct the relationship between solder joint strength and the conditions for the formation of a galvanic Ni barrier layer. Graphs of the peel force versus the pH of the nickel plating electrolyte, changes in electrolyte pH depending on the number of parts processed, and calculated equilibrium concentrations of nickel complexes in the electrolyte that affect the quality of the resulting coating are presented. Using mathematical modeling, an attempt was made to predict the redistribution of nickel complexes when adjusting the electrolyte composition and pH using various methods. The calculated strength results were compared with those obtained in practice. Approaches to mitigating the negative effect of nickel succinate are proposed.
- Open Access
- 11 November 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (18)
Scanning spreading resistance microscopy for p – n junction and carrier distribution analysis in InGaAs/AlGaAs quantum well laser heterostructure
Scanning spreading resistance microscopy (SSRM) was used to study the spatial distribution of carrier concentration in an InGaAs/AlGaAs quantum well laser heterostructure. An analysis of the dependence of current contrast on the polarity of the applied dc bias showed that measurements should be performed at both positive and negative biases above the threshold voltage to visualize all layers of the structure. The actual position of the p–n junction can be determined by finding the point on the averaged SSRM profiles where the current signal is zero. Mathematical modeling of band diagrams and current–voltage (I–V) characteristics of p+-diamond–AlGaAs heterojunctions has shown that, regardless of the AlGaAs conductivity type, the current in the tip contact with the layers of the structure is determined not only by the layers’ conductivity but also by the height of the barrier for holes in the valence band. SSRM can be used as an effective diagnostic tool for the rapid assessment of the conductive properties of laser heterostructures, complementing other traditional analysis methods such as electrochemical capacitance–voltage profiling and secondary ion mass spectrometry.
- 11 November 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (18)
Open AccessScanning spreading resistance microscopy for p – n junction and carrier distribution analysis in InGaAs/AlGaAs quantum well laser heterostructure
Scanning spreading resistance microscopy (SSRM) was used to study the spatial distribution of carrier concentration in an InGaAs/AlGaAs quantum well laser heterostructure. An analysis of the dependence of current contrast on the polarity of the applied dc bias showed that measurements should be performed at both positive and negative biases above the threshold voltage to visualize all layers of the structure. The actual position of the p–n junction can be determined by finding the point on the averaged SSRM profiles where the current signal is zero. Mathematical modeling of band diagrams and current–voltage (I–V) characteristics of p+-diamond–AlGaAs heterojunctions has shown that, regardless of the AlGaAs conductivity type, the current in the tip contact with the layers of the structure is determined not only by the layers’ conductivity but also by the height of the barrier for holes in the valence band. SSRM can be used as an effective diagnostic tool for the rapid assessment of the conductive properties of laser heterostructures, complementing other traditional analysis methods such as electrochemical capacitance–voltage profiling and secondary ion mass spectrometry.
- Open Access
- 1 December 2023
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 49 (S3) , S159-S162
3.8 THz Quantum Cascade Laser Grown by Metalorganic Vapor Phase Epitaxy
We have demonstrated a quantum cascade laser (QCL) with a generation frequency of about 3.8 THz, grown by metal-organic vapor phase epitaxy. The multilayer heterostructure for QCLs consists of 185 repetitions of an active module containing four GaAs/Al0.15Ga0.85As quantum wells. The threshold current and threshold voltage of the fabricated QCL were 2.25 kA/cm2 and 19.7 V, respectively. The QCL oscillations were carried out in the multimode regime, and the detection of terahertz radiation continued with an increase in the laser temperature up to 60 K.
- 1 December 2023
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 49 (S3) , S159-S162
Open Access3.8 THz Quantum Cascade Laser Grown by Metalorganic Vapor Phase Epitaxy
We have demonstrated a quantum cascade laser (QCL) with a generation frequency of about 3.8 THz, grown by metal-organic vapor phase epitaxy. The multilayer heterostructure for QCLs consists of 185 repetitions of an active module containing four GaAs/Al0.15Ga0.85As quantum wells. The threshold current and threshold voltage of the fabricated QCL were 2.25 kA/cm2 and 19.7 V, respectively. The QCL oscillations were carried out in the multimode regime, and the detection of terahertz radiation continued with an increase in the laser temperature up to 60 K.
- 1 April 2022
- Published by Pleiades Publishing Ltd in Inorganic Materials
- Vol. 58 (4) , 425-432
Calculational Evaluation of the Adsorption–Desorption Behavior of Pyrolysis Products in GaAsxP1 – x Metalorganic Vapor Phase Epitaxy
Density functional theory calculations have been used to determine the adsorption and desorption potentials of pyrolysis products on the substrate in the GaAsxP1 – x/GaAs metalorganic vapor phase epitaxy process. The results have been used in kinetic Monte Carlo simulation of the behavior of the pyrolysis products on the growth surface, with allowance for adsorption, desorption, and diffusion. The simulation results agree well with experimental data. The proposed calculation algorithm can be used to study the adsorption–desorption behavior of materials in other systems.
- 1 April 2022
- Published by Pleiades Publishing Ltd in Inorganic Materials
- Vol. 58 (4) , 425-432
Calculational Evaluation of the Adsorption–Desorption Behavior of Pyrolysis Products in GaAsxP1 – x Metalorganic Vapor Phase Epitaxy
Density functional theory calculations have been used to determine the adsorption and desorption potentials of pyrolysis products on the substrate in the GaAsxP1 – x/GaAs metalorganic vapor phase epitaxy process. The results have been used in kinetic Monte Carlo simulation of the behavior of the pyrolysis products on the growth surface, with allowance for adsorption, desorption, and diffusion. The simulation results agree well with experimental data. The proposed calculation algorithm can be used to study the adsorption–desorption behavior of materials in other systems.
- 10 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (1) , 35-38
Tunnel-Coupled Laser Diode Microarray as a kW-Level 100-ns Pulsed Optical Power Source (λ = 910 nm)
Pulsed 910nm laser sources based on tunnel-coupled AlGaAs/InGaAs/GaAs heterostructures have been developed and studied. To provide the maximum brightness and operation in the linear part of the light-current characteristic, a microarray design was developed. This design includes $3\times 800$ - $\mu \text{m}$ -wide stripes in the emitting region. It was demonstrated that, under pumping with 760 A/100 ns current pulses, laser pulse with peak power of 1150 W can be generated. Raising the working temperature led to an insignificant deterioration of emission characteristics, which was manifested by the peak powers of 1030 W/750 A/50°C and 905 W/720 A/75°C.
- 10 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (1) , 35-38
Tunnel-Coupled Laser Diode Microarray as a kW-Level 100-ns Pulsed Optical Power Source (λ = 910 nm)
Pulsed 910nm laser sources based on tunnel-coupled AlGaAs/InGaAs/GaAs heterostructures have been developed and studied. To provide the maximum brightness and operation in the linear part of the light-current characteristic, a microarray design was developed. This design includes $3\times 800$ - $\mu \text{m}$ -wide stripes in the emitting region. It was demonstrated that, under pumping with 760 A/100 ns current pulses, laser pulse with peak power of 1150 W can be generated. Raising the working temperature led to an insignificant deterioration of emission characteristics, which was manifested by the peak powers of 1030 W/750 A/50°C and 905 W/720 A/75°C.
- 1 October 2021
- Published by IOP Publishing in Quantum Electronics
- Vol. 51 (10) , 909-911
High-power AlGaInAs/InP semiconductor lasers with an ultra-narrow waveguide emitting in the spectral range 1.9−2.0 μm
- 1 October 2021
- Published by IOP Publishing in Quantum Electronics
- Vol. 51 (10) , 909-911
High-power AlGaInAs/InP semiconductor lasers with an ultra-narrow waveguide emitting in the spectral range 1.9−2.0 μm
- 1 March 2020
- Published by Pleiades Publishing Ltd in Semiconductors
- Vol. 54 (3) , 362-365
Photoreversible Current in InGaN/GaN-Based LED Heterostructures with Different Numbers of QWs
InGaN/GaN-based LED heterostructures with different numbers of quantum wells are investigated by photocurrent spectroscopy in the wavelength range of 350–500 nm. As a result of the analysis of a series of spectra obtained at various p–n-junction biases, the effect of changing photocurrent direction when varying the excitation wavelength (photoreversible effect) is discovered. The range of p–n-junction biases for which this effect is observed in structures with different numbers of quantum wells in the active region is established.
- 1 March 2020
- Published by Pleiades Publishing Ltd in Semiconductors
- Vol. 54 (3) , 362-365
Photoreversible Current in InGaN/GaN-Based LED Heterostructures with Different Numbers of QWs
InGaN/GaN-based LED heterostructures with different numbers of quantum wells are investigated by photocurrent spectroscopy in the wavelength range of 350–500 nm. As a result of the analysis of a series of spectra obtained at various p–n-junction biases, the effect of changing photocurrent direction when varying the excitation wavelength (photoreversible effect) is discovered. The range of p–n-junction biases for which this effect is observed in structures with different numbers of quantum wells in the active region is established.
- 11 November 2016
- Published by Springer Nature in Russian Physics Journal
- Vol. 59 (7) , 934-937
Effect of a Short-Period InGaN/GaN Superlattice on the Efficiency of Blue LEDs at High Level of Optical Pumping
- 11 November 2016
- Published by Springer Nature in Russian Physics Journal
- Vol. 59 (7) , 934-937
Effect of a Short-Period InGaN/GaN Superlattice on the Efficiency of Blue LEDs at High Level of Optical Pumping
- 25 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. R3-41
Effect of waveguide design on AlGalnAs/InP laser diode characteristics
1550nm-lasers based on MOCVD-grown heterostructures are investigated. It is determined, that additional barrier layers grown between waveguide and cladding layers block carrier leakage into the cladding layers but results in internal optical loss rise with drive current increase. It is demonstrated that incorporation of barrier layers allows attaining 92% internal quantum efficiency and 3.2W CW RT output optical power.
- 25 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. R3-41
Effect of waveguide design on AlGalnAs/InP laser diode characteristics
1550nm-lasers based on MOCVD-grown heterostructures are investigated. It is determined, that additional barrier layers grown between waveguide and cladding layers block carrier leakage into the cladding layers but results in internal optical loss rise with drive current increase. It is demonstrated that incorporation of barrier layers allows attaining 92% internal quantum efficiency and 3.2W CW RT output optical power.
- 1 December 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10928081,p. 459-460
New type of high power pulse semiconductor laser based on epitaxially-integrated AlGaAs/GaAs thyristor heterostructure
We present the latest theoretical and experimental results on nonlinear dynamic characteristics of laser-thyristor. We have experimentally demonstrated 4MHz/4.5W high frequency lasing of laser-thyristor in 890-910 nm spectral range. The minimum values of the energy and amplitude of the control current density pulse required to turn on 28 W peak output optical power of laser-thyristor were 1.4 nJ and 0.6 A/cm 2 , respectively.
- 1 December 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10928081,p. 459-460
New type of high power pulse semiconductor laser based on epitaxially-integrated AlGaAs/GaAs thyristor heterostructure
We present the latest theoretical and experimental results on nonlinear dynamic characteristics of laser-thyristor. We have experimentally demonstrated 4MHz/4.5W high frequency lasing of laser-thyristor in 890-910 nm spectral range. The minimum values of the energy and amplitude of the control current density pulse required to turn on 28 W peak output optical power of laser-thyristor were 1.4 nJ and 0.6 A/cm 2 , respectively.