Golam Newaz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Golam Newaz has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Ahsan Mian
Department of Mechanical and Materials Engineering, Wright State University, Dayton, OH 45435, USA
2 shared publications - Daniel. G. Georgiev
Department of Electrical Engineering and Computer Science, The University of Toledo, Toledo, OH, USA
2 shared publications - Gina S. Shreve
Department of Chemical Engineering and Material Science, Wayne State University, 5050 Anthony Wayne Dr., Detroit, MI 48202, USA
1 shared publication Greg Auner
College of Engineering, Wayne State University
1 shared publication- Gregory W. Auner
Smart Sensors and Integrated Microsystems Program, Michael and Marian Ilitch Department of Surgery, School of Medicine Wayne State University Detroit Michigan USA
1 shared publication Hans Herfurth
Fraunhofer Center for Laser Technology
1 shared publication
Latest Publications
- 14 November 2014
- Published by ASME International
Residual Stresses in Laser Micro-Joints of Dissimilar Materials
Detailed analyses of thermal residual stress profiles due to laser micro-joining of several dissimilar material combinations, titanium (Ti) and polyimide (PI) [1], titanium coated glass (Gl) and polyimide [2], and glass and silicon (Si), are vital for the long-term applications of bio-implants and opto-electronics. In these studies, comprehensive three dimensional (3D) transient simulations for thermal and thermal stress analyses of transmission laser micro-joining of dissimilar materials have been performed by using the finite element (FE) code ABAQUS, along with moving Gaussian or super Gaussian laser heat source. The laser beam moving at a certain velocity, passes through the transparent material (e.g. PI or Gl), gets absorbed by the absorbing material (e.g. Ti or Si), and eventually softens/melts the interfacial materials to form the bond. Computational results have been compared with experiments in terms of temperatures and bond widths, and good comparisons have been observed in all combinations. Then the computational model has been used to optimize the process parameters and after this residual stress profiles of the laser-micro-joints have been calculated using the temperature profiles obtained from the thermal analyses as the systems cool down to room temperature. According to the various stress profiles, none of the stresses cross the tensile or the compressive strengths in cases of all the dissimilar material combinations at room temperature. A critical discussion has been included comparing the thermal residual stresses generated in the three combinations of dissimilar materials being used in these studies. A conclusion has been made on the formation processes of these stresses in laser micro-joining processes of dissimilar materials. This report will help to estimate the expected residual stresses in the laser micro-joining processes of dissimilar materials and will shed insight on how to select a better dissimilar material combination for a laser precision joining process.
- 14 November 2014
- Published by ASME International
Residual Stresses in Laser Micro-Joints of Dissimilar Materials
Detailed analyses of thermal residual stress profiles due to laser micro-joining of several dissimilar material combinations, titanium (Ti) and polyimide (PI) [1], titanium coated glass (Gl) and polyimide [2], and glass and silicon (Si), are vital for the long-term applications of bio-implants and opto-electronics. In these studies, comprehensive three dimensional (3D) transient simulations for thermal and thermal stress analyses of transmission laser micro-joining of dissimilar materials have been performed by using the finite element (FE) code ABAQUS, along with moving Gaussian or super Gaussian laser heat source. The laser beam moving at a certain velocity, passes through the transparent material (e.g. PI or Gl), gets absorbed by the absorbing material (e.g. Ti or Si), and eventually softens/melts the interfacial materials to form the bond. Computational results have been compared with experiments in terms of temperatures and bond widths, and good comparisons have been observed in all combinations. Then the computational model has been used to optimize the process parameters and after this residual stress profiles of the laser-micro-joints have been calculated using the temperature profiles obtained from the thermal analyses as the systems cool down to room temperature. According to the various stress profiles, none of the stresses cross the tensile or the compressive strengths in cases of all the dissimilar material combinations at room temperature. A critical discussion has been included comparing the thermal residual stresses generated in the three combinations of dissimilar materials being used in these studies. A conclusion has been made on the formation processes of these stresses in laser micro-joining processes of dissimilar materials. This report will help to estimate the expected residual stresses in the laser micro-joining processes of dissimilar materials and will shed insight on how to select a better dissimilar material combination for a laser precision joining process.
- 13 August 2013
- Published by Springer Nature
- p. 301-330
Thin Film Coatings as Electrodes in Neuroscience
- 13 August 2013
- Published by Springer Nature
- p. 301-330
Thin Film Coatings as Electrodes in Neuroscience
- 25 August 2005
- Published by Springer Nature in Journal of Materials Science
- Vol. 40 (21) , 5641-5647
Laser fabrication and characterization of sub-millimeter joints between polyimide and Ti-coated borosilicate glass
- 25 August 2005
- Published by Springer Nature in Journal of Materials Science
- Vol. 40 (21) , 5641-5647
Laser fabrication and characterization of sub-millimeter joints between polyimide and Ti-coated borosilicate glass
- 1 August 2005
- Published by Elsevier in Applied Surface Science
- Vol. 249 (1-4) , 45-53
Excimer laser modification of thin AlN films
- 1 August 2005
- Published by Elsevier in Applied Surface Science
- Vol. 249 (1-4) , 45-53
Excimer laser modification of thin AlN films
- 10 November 2001
- Published by ASME International
- p. 19-25
The Role of Adhesive in the Load Response of Adhesively Bonded Aluminum Hat Sections Under Axial Compression
Aluminum hat section, either adhesively bonded or unbonded, experiences buckling, post buckling and plastic collapse when axially compressed. However, there exist obvious differences in the load response between the bonded and unbonded hat sections. Finite element eigenvalue buckling analysis is carried out to predict the buckling load and mode. Experiments show that when adhesively bonded hat sections begin to buckle there is a transformation from the first buckling mode to the higher ones, while the unbonded hat sections develop the post buckling based on the lowest buckling mode. The different buckling modes result in not only different buckling loads but different peak loads of the hat sections as well. Finally, the ultimate compressive strength formulae are proposed for the hat sections.
- 10 November 2001
- Published by ASME International
- p. 19-25
The Role of Adhesive in the Load Response of Adhesively Bonded Aluminum Hat Sections Under Axial Compression
Aluminum hat section, either adhesively bonded or unbonded, experiences buckling, post buckling and plastic collapse when axially compressed. However, there exist obvious differences in the load response between the bonded and unbonded hat sections. Finite element eigenvalue buckling analysis is carried out to predict the buckling load and mode. Experiments show that when adhesively bonded hat sections begin to buckle there is a transformation from the first buckling mode to the higher ones, while the unbonded hat sections develop the post buckling based on the lowest buckling mode. The different buckling modes result in not only different buckling loads but different peak loads of the hat sections as well. Finally, the ultimate compressive strength formulae are proposed for the hat sections.