Bakhtiyor Baratov
Research Subjects
Bakhtiyor Baratov has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Javokhir Toshov
Department of Mining Electromechanics, Tashkent State Technical University, University Street, 2, Tashkent 100095, Uzbekistan
4 shared publications - Mukhammedrakhym Rabatuly
Abylkas Saginov Karaganda Technical University
3 shared publications Almalyk Branch Of Nust Misis
2 shared publications- D.I. Erkinov2 shared publications
- Karibek Tagayevich Sherov
S.Seifullin Kazakh Agro Technical University
2 shared publications - Aisaule Zheldikbaeva
Abylkas Saginov Karaganda Technical University
1 shared publication
Latest Publications
- 30 June 2026
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 20 (2) , 31-45
Assessment of factors contributing to failures in hydraulic systems of mining excavators
Purpose. To identify and quantify the main factors causing failures in hydraulic systems of open-pit excavators, with particular emphasis on the influence of the cleanliness and physicochemical condition of the working fluid on the reliability and service life of hydraulic units. Methods. The study is based on an integrated approach that includes an analytical generalization of literature and operational data on hydraulic system failures, determination of working fluid cleanliness class using a Luvatech S41 particle counter, and physicochemical characterization of fluids by infrared spectroscopy, X-ray fluorescence analysis, visual assessment, and microscopy. The effect of contamination on the service life of hydraulic units was additionally evaluated using a calculation model that accounts for particle concentration and particle-size distribution. Findings. It was established that working fluid contamination accounts for approximately 70% of hydraulic system failures. Particle count analysis showed a progressive increase in contamination with increasing operating time, with the most pronounced growth observed for the 2-5 and 5-10 μm fractions, indicating intensified abrasive wear in the hydraulic system. X-ray fluorescence analysis revealed an increase in SiO2 content from 88.740 to 93.474%, indicating contamination of the working fluid by silicon-bearing abrasive particles. Infrared spectroscopy identified structural changes in the working fluid and the appearance of additional absorption bands associated with its chemical degradation during operation. Microscopic examination of used oil confirmed the presence of solid impurities. An economically and technically justified working fluid cleanliness level corresponding to ISO 4406 class 15/13 was determined, thereby improving reliability and reducing operating costs. Originality. For the first time, an integrated approach is applied, combining particle-size analysis, physicochemical diagnostics of the working fluid, and assessment of hydraulic unit life to establish the relationship between working-fluid cleanliness, contamination characteristics, and hydraulic-system reliability under real operating conditions. Practical implications. The results obtained can be used to improve filtration systems, optimize maintenance strategies, and support early diagnostics and predictive maintenance of hydraulic equipment at mining enterprises.
- 30 June 2026
- Published by Dnipro University of Technology in Mining of Mineral Deposits
- Vol. 20 (2) , 31-45
Assessment of factors contributing to failures in hydraulic systems of mining excavators
Purpose. To identify and quantify the main factors causing failures in hydraulic systems of open-pit excavators, with particular emphasis on the influence of the cleanliness and physicochemical condition of the working fluid on the reliability and service life of hydraulic units. Methods. The study is based on an integrated approach that includes an analytical generalization of literature and operational data on hydraulic system failures, determination of working fluid cleanliness class using a Luvatech S41 particle counter, and physicochemical characterization of fluids by infrared spectroscopy, X-ray fluorescence analysis, visual assessment, and microscopy. The effect of contamination on the service life of hydraulic units was additionally evaluated using a calculation model that accounts for particle concentration and particle-size distribution. Findings. It was established that working fluid contamination accounts for approximately 70% of hydraulic system failures. Particle count analysis showed a progressive increase in contamination with increasing operating time, with the most pronounced growth observed for the 2-5 and 5-10 μm fractions, indicating intensified abrasive wear in the hydraulic system. X-ray fluorescence analysis revealed an increase in SiO2 content from 88.740 to 93.474%, indicating contamination of the working fluid by silicon-bearing abrasive particles. Infrared spectroscopy identified structural changes in the working fluid and the appearance of additional absorption bands associated with its chemical degradation during operation. Microscopic examination of used oil confirmed the presence of solid impurities. An economically and technically justified working fluid cleanliness level corresponding to ISO 4406 class 15/13 was determined, thereby improving reliability and reducing operating costs. Originality. For the first time, an integrated approach is applied, combining particle-size analysis, physicochemical diagnostics of the working fluid, and assessment of hydraulic unit life to establish the relationship between working-fluid cleanliness, contamination characteristics, and hydraulic-system reliability under real operating conditions. Practical implications. The results obtained can be used to improve filtration systems, optimize maintenance strategies, and support early diagnostics and predictive maintenance of hydraulic equipment at mining enterprises.
- Open Access
- 29 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (9) , 4323
Studies of the Stress–Strain State of Rocks Under the Impact of Penetrators of Various Configurations Using the Ansys Software Package
This study investigates the stress–strain state of rocks subjected to the impact of penetrators with diverse configurations, employing numerical simulations in the ANSYS Workbench Static Structural module. The research focuses on the interaction between roller cone drill bit teeth and rock formations during blast hole drilling. Through finite element modeling using a linear elastic constitutive model, the influence of penetrator geometry, position relative to borehole walls, angle of attack, and distance to open surfaces on rock fracture parameters is analyzed. Key quantitative findings include: the relative breaking force near the borehole wall reaches 2.8 for soft rocks (siltstones) with a 10 mm tooth diameter, and decreases to approximately 1.0 at a distance of 1.5d from the wall; the optimal angle of attack ranges from 60° to 90° depending on rock hardness; and the proximity to a free surface reduces fracture resistance to as low as 0.23 of the baseline value. Six sets of parabolic regression equations (R2 > 0.95) are derived for relative breaking forces across three rock hardness groups and two tooth diameters. Optimal parameters for tooth placement, borehole bottom shapes, and operational conditions are proposed. Implementation of the recommended parameters is estimated to increase drilling efficiency by 10–20% and extend tool service life by 15–30%. The findings provide a scientific foundation for designing advanced roller cone drill bits suitable for rocks with Protodyakonov hardness indices ranging from f = 5 to f = 18.
- 29 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (9) , 4323
Open AccessStudies of the Stress–Strain State of Rocks Under the Impact of Penetrators of Various Configurations Using the Ansys Software Package
This study investigates the stress–strain state of rocks subjected to the impact of penetrators with diverse configurations, employing numerical simulations in the ANSYS Workbench Static Structural module. The research focuses on the interaction between roller cone drill bit teeth and rock formations during blast hole drilling. Through finite element modeling using a linear elastic constitutive model, the influence of penetrator geometry, position relative to borehole walls, angle of attack, and distance to open surfaces on rock fracture parameters is analyzed. Key quantitative findings include: the relative breaking force near the borehole wall reaches 2.8 for soft rocks (siltstones) with a 10 mm tooth diameter, and decreases to approximately 1.0 at a distance of 1.5d from the wall; the optimal angle of attack ranges from 60° to 90° depending on rock hardness; and the proximity to a free surface reduces fracture resistance to as low as 0.23 of the baseline value. Six sets of parabolic regression equations (R2 > 0.95) are derived for relative breaking forces across three rock hardness groups and two tooth diameters. Optimal parameters for tooth placement, borehole bottom shapes, and operational conditions are proposed. Implementation of the recommended parameters is estimated to increase drilling efficiency by 10–20% and extend tool service life by 15–30%. The findings provide a scientific foundation for designing advanced roller cone drill bits suitable for rocks with Protodyakonov hardness indices ranging from f = 5 to f = 18.
- 22 January 2026
- Published by Institute of Metallurgy and Ore Benefication (Publications) in Kompleksnoe Ispolzovanie Mineralnogo Syra = Complex Use of Mineral Resources
- Vol. 342 (3) , 27-34
Mathematical Model of the Dynamics of the Armament of the Tricone Drill Bit
This study presents a mathematical model of the dynamics of tricone drill bits, which remain widely used in open-pit mining due to their reliability and versatility. Despite their extensive application, improving their efficiency and durability remains a relevant issue. The main operational challenges are identified, including insufficient knowledge of the stress–strain state of rocks in the contact zone and the effect of tooth geometry on kinematics and rock-breaking efficiency. Analytical dependencies are proposed to account for bit geometry, trajectory motion, transmission ratios, and tooth–rock interaction. Based on the principles of theoretical mechanics, performance criteria are formulated through specific contact and volumetric work of rock destruction, enabling an objective assessment of energy consumption. The model demonstrates the potential of analytical methods for optimizing drill bit design and kinematics, reducing energy consumption, increasing productivity, and extending tool life. The results can be applied in the design of next-generation drill bits and in engineering software for selecting rational drilling parameters under specific geological conditions. The proposed approach provides a foundation for further studies in mathematical modeling of rock destruction dynamics and the advancement of open-pit mining technologies.
- 22 January 2026
- Published by Institute of Metallurgy and Ore Benefication (Publications) in Kompleksnoe Ispolzovanie Mineralnogo Syra = Complex Use of Mineral Resources
- Vol. 342 (3) , 27-34
Mathematical Model of the Dynamics of the Armament of the Tricone Drill Bit
This study presents a mathematical model of the dynamics of tricone drill bits, which remain widely used in open-pit mining due to their reliability and versatility. Despite their extensive application, improving their efficiency and durability remains a relevant issue. The main operational challenges are identified, including insufficient knowledge of the stress–strain state of rocks in the contact zone and the effect of tooth geometry on kinematics and rock-breaking efficiency. Analytical dependencies are proposed to account for bit geometry, trajectory motion, transmission ratios, and tooth–rock interaction. Based on the principles of theoretical mechanics, performance criteria are formulated through specific contact and volumetric work of rock destruction, enabling an objective assessment of energy consumption. The model demonstrates the potential of analytical methods for optimizing drill bit design and kinematics, reducing energy consumption, increasing productivity, and extending tool life. The results can be applied in the design of next-generation drill bits and in engineering software for selecting rational drilling parameters under specific geological conditions. The proposed approach provides a foundation for further studies in mathematical modeling of rock destruction dynamics and the advancement of open-pit mining technologies.
- 25 December 2025
- Published by Institute of Metallurgy and Ore Benefication (Publications) in Kompleksnoe Ispolzovanie Mineralnogo Syra = Complex Use of Mineral Resources
- Vol. 341 (2) , 60-70
Comparative Analysis of Mathematical Models of Drilling in Heterogeneous Geological Sections
This paper presents a comparative analysis of four main types of well drilling models in heterogeneous geological sections: mechanical-mathematical, energy, kinematic, and empirical. It is shown that each group of models focuses on different aspects of the process: the physics of bit-rock interaction (mechanical-mathematical approach), the energy efficiency of rock mass destruction (energy), the trajectory and movement of the tool (kinematic), as well as statistical patterns and the prediction of complications (empirical). The interaction between the bit and the rock is considered depending on their physical and mechanical properties. A comparison of the rotation speed of the rotor and bit is provided depending on the rock hardness. Based on a review of modern publications and the practical experience of leading service companies (Equinor, Schlumberger, Halliburton), the strengths and weaknesses of each approach are identified, and the need for their integration is substantiated. It is established that the integrated use of models of different classes allows not only to describe and explain phenomena but also to manage the drilling process in conditions of high geological variability.
- 25 December 2025
- Published by Institute of Metallurgy and Ore Benefication (Publications) in Kompleksnoe Ispolzovanie Mineralnogo Syra = Complex Use of Mineral Resources
- Vol. 341 (2) , 60-70
Comparative Analysis of Mathematical Models of Drilling in Heterogeneous Geological Sections
This paper presents a comparative analysis of four main types of well drilling models in heterogeneous geological sections: mechanical-mathematical, energy, kinematic, and empirical. It is shown that each group of models focuses on different aspects of the process: the physics of bit-rock interaction (mechanical-mathematical approach), the energy efficiency of rock mass destruction (energy), the trajectory and movement of the tool (kinematic), as well as statistical patterns and the prediction of complications (empirical). The interaction between the bit and the rock is considered depending on their physical and mechanical properties. A comparison of the rotation speed of the rotor and bit is provided depending on the rock hardness. Based on a review of modern publications and the practical experience of leading service companies (Equinor, Schlumberger, Halliburton), the strengths and weaknesses of each approach are identified, and the need for their integration is substantiated. It is established that the integrated use of models of different classes allows not only to describe and explain phenomena but also to manage the drilling process in conditions of high geological variability.
- 8 November 2025
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 42 (6) , 3695-3710
Designing Efficient Drill Bits Using The Finite Element Analysis Method
- 8 November 2025
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 42 (6) , 3695-3710
Designing Efficient Drill Bits Using The Finite Element Analysis Method