OLOleksii Lanets

Oleksii Lanets

*This is an algorithmically generated author record based on publicly available information.

Oleksii Lanets has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • PARAMETER DEVELOPMENT AND ANALYSIS OF THE OSCILLATORY SYSTEM OF A TWO-MASS RESONANT VIBRATING TABLE WITH AN INERTIAL DRIVE

    by Roman Kapalo, Oleksii Lanets, Oleksii Vambol, Iryna Derevenko

    The widespread use of vibrating tables in industry motivates researchers to develop new, efficient designs that can increase production profitability. For this purpose, the authors present a new schematic design of a vibrating table with an inertial drive, proposed to be powered by a hydraulic coupling. The principle of operation is as follows: the driving shaft of the hydraulic coupling is rotated by an electric motor, while its driven shaft is connected to an unbalanced mass. In this case, it is assumed that the rotor of the induction electric motor reaches its nominal operating mode, and the unbalanced speed “locks” near the resonant peak due to processes associated with the Sommerfeld effect. This enables the automatic maintenance of the forced oscillation frequency near the pre-resonant regime, thereby implementing energy-saving operating modes in the vibration system of the vibrating table, without the need for expensive control systems. A problem arises because the implementation of such a design requires a clear justification of the inertial, stiffness, and force parameters of the oscillatory system. In addition, it is necessary to analyze the dynamic characteristics of the oscillatory system. This will enable a priori verification of the design's operability with the required technological parameters. This article addresses the issues discussed. For this purpose, the authors present the methodology for determining the inertial, stiffness, and force parameters of a two-mass resonant vibrating table with an inertial drive. For the specified operating mode, analytical expressions are given for determining the amplitudes of mass oscillations, stiffness coefficients of elastic elements, the amplitude of the excitation force, and unbalance parameters. The dynamic parameters of such an oscillatory system, namely the dynamic coefficients of the oscillating masses, are analytically derived and analyzed. A specific example demonstrates the application of the proposed approach to calculating a two-mass oscillatory system with a force disturbance from a reactive mass. The amplitude-frequency characteristic of the oscillatory system is constructed and analyzed. The value of this article lies in presenting a comprehensive methodology for calculating the vibration systems mentioned. A distinctive feature of this methodology is that it provides refined analytical expressions for setting the parameters of the vibration system. The material is accompanied by clear visualization. The presented methodology can be used by engineers when designing vibration technological equipment of this type.


  • SUBSTANTIATION OF THE ADVANTAGES OF USING PLANE ELASTIC ELEMENTS IN THE RESONANT DESIGN OF A VIBRATING TABLE OF THE ECCENTRIC-PENDULUM TYPE

    by Taras Svyshch, Oleksii Lanets, Oleksii Vambol, Iryna Derevenko

    This article presents an analytical and engineering justification for the use of flat elastic elements in eccentric-pendulum-type resonant vibration tables. The study addresses the design, calculation, and structural optimization of resonant elastic nodes, which ensure directional oscillations, define dynamic performance, and determine the durability and reliability of the machine. Stiffness and strength calculation procedures are derived for elastic components of rectangular and circular cross-sections, considering material properties, geometric parameters, and stress constraints under cyclic loading. Analytical results indicate that circular elements experience higher bending stresses than rectangular ones for equivalent stiffness, requiring increased length to achieve comparable durability. Finite-element simulations validate these findings, confirming the superior structural efficiency, lower operating stresses, and enhanced geometric adaptability of flat elements. The research provides a rigorous basis for selecting flat elastic components in the design of high-performance resonant vibration systems.

  • MODERNIZATION OF SINGLE- AND TWO-MASS RESONANT VIBRATION MACHINES WITH INERTIAL DRIVE

    by Ivan Kolodiy, Oleksii Lanets, Oleksii Vambol, Iryna Derevenko

    The article addresses excessive energy consumption in resonance vibration machines with inertial drives, widely used in mechanical engineering, construction, chemical, metallurgical, and mining industries. Conventional design approaches limit energy efficiency, motivating the modernization of one- and two-mass resonance systems into three-mass inter-resonance configurations. Using a method for determining inertia–stiffness parameters, the study ensures synchronous inter-resonance oscillatory modes, enhancing dynamic amplification and reducing drive power. Analytical modeling of the three-mass system, comprising active, intermediate, and reactive masses connected by elastic and damping elements, yields closed-form expressions for steady-state amplitudes and stiffness parameters. A phase-synchronization criterion is applied to determine the reactive mass, enabling convergence of resonance peaks and maximal dynamic gain. The proposed methodology provides a unified framework for upgrading existing resonance machines, achieving significant energy savings—up to an order of magnitude—while maintaining required oscillation amplitudes. These results offer a practical tool for energy-efficient modernization of industrial vibratory machinery with inertial drives.