Vladimir Krylov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Vladimir Krylov has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
A. A. Klementiev
National Research University Moscow Power Engineering Institute (NRU MPEI), Moscow, Russia
1 shared publication- Alexey Loskutov
Department of Electric Power Engineering, Power Supply and Power Electronics, Nizhny Novgorod State Technical University n.a. R.E. Alekseev, 603155 Nizhny Novgorod, Russia
1 shared publication - Dmitry Ponomarev
Centre Inria d’Université Côte d’Azur
1 shared publication G. G. Yan’KOv
Tsiolkovski Kaluga State University, Kaluga, Russia
1 shared publication- Konstantin Borisovich Minko
National Research University Moscow Power Engineering Institute (NRU MPEI), Moscow, Russia
1 shared publication V. I. Artemov
National Research University Moscow Power Engineering Institute (NRU MPEI), Moscow, Russia
1 shared publication
Latest Publications
- 10 September 2021
- Published by Pleiades Publishing Ltd in Thermal Engineering
- Vol. 68 (9) , 705-716
An Engineering Model of Steam Condensation from a Flowing Steam-Gas Mixture on a Bundle Made of Horizontal Tubes
Based on an analysis of modern approaches to the calculation of heat-and-mass transfer processes in water-cooled condensers, an engineering model of steam condensation from a flowing steam-gas mixture (SGM) on a bundle made of smooth horizontal tubes is proposed. This model was verified against available experimental data and predictions by the detailed CFD-model described in our previous publications. The engineering model adequately describes the experimental data. Local characteristics of heat-and-mass transfer processes were studied in small-scale condenser tube bundles with a constant or variable cross-section fed with SGM having a volume fraction of air from 0 to 15%. For the case with an air volume fraction of 10% at the condenser inlet, the distributions of heat-transfer coefficient, heat flux, and total removed power removed along the SGM flow, as well as the distribution of heat flux density among the tubes of the first, fifth, and ninth rows are presented. A comparative analysis revealed that, despite almost the same average characteristics, the distribution of local heat-transfer coefficients is more uniform in a tube bundle with a decreasing cross-section along the SGM flow. The distributions of local heat-and-mass transfer characteristics calculated by the engineering model agree quite well with the predictions by the detailed CFD-model. Some qualitative disagreement can be explained by the fact that the engineering model uses characteristics averaged over the cross section of a row, and the detailed CFD model takes into account the nonuniformity in the velocity field and composition of the SGM flowing over the tube bundle.
- 10 September 2021
- Published by Pleiades Publishing Ltd in Thermal Engineering
- Vol. 68 (9) , 705-716
An Engineering Model of Steam Condensation from a Flowing Steam-Gas Mixture on a Bundle Made of Horizontal Tubes
Based on an analysis of modern approaches to the calculation of heat-and-mass transfer processes in water-cooled condensers, an engineering model of steam condensation from a flowing steam-gas mixture (SGM) on a bundle made of smooth horizontal tubes is proposed. This model was verified against available experimental data and predictions by the detailed CFD-model described in our previous publications. The engineering model adequately describes the experimental data. Local characteristics of heat-and-mass transfer processes were studied in small-scale condenser tube bundles with a constant or variable cross-section fed with SGM having a volume fraction of air from 0 to 15%. For the case with an air volume fraction of 10% at the condenser inlet, the distributions of heat-transfer coefficient, heat flux, and total removed power removed along the SGM flow, as well as the distribution of heat flux density among the tubes of the first, fifth, and ninth rows are presented. A comparative analysis revealed that, despite almost the same average characteristics, the distribution of local heat-transfer coefficients is more uniform in a tube bundle with a decreasing cross-section along the SGM flow. The distributions of local heat-and-mass transfer characteristics calculated by the engineering model agree quite well with the predictions by the detailed CFD-model. Some qualitative disagreement can be explained by the fact that the engineering model uses characteristics averaged over the cross section of a row, and the detailed CFD model takes into account the nonuniformity in the velocity field and composition of the SGM flowing over the tube bundle.
- 1 December 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 351-356
Toward the power InterGrid
The paper is focused on the new approach to electric power distribution. Following the analogy of telecommunications network and power grids evolution a power packetizing technology is proposed. The new concept of the Packet Power Grid (PPG) is proposed as a set of different power sources and power consumers joined by power lines and electronic switches controlled by a supporting information computer network. Different electrical sensors form an important part of the PPG as well. The paper overviews the PPG as the next power grid evolution step after the Smart Grid. The PPG approach solves a number of problems of open concurrent power market development e.g. highly-efficient energy usage and numerous small sources adoption. The growing Packet Power Grid can play the role of the global power highway the same way as the Internet plays the role of the global information highway.
- 1 December 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 351-356
Toward the power InterGrid
The paper is focused on the new approach to electric power distribution. Following the analogy of telecommunications network and power grids evolution a power packetizing technology is proposed. The new concept of the Packet Power Grid (PPG) is proposed as a set of different power sources and power consumers joined by power lines and electronic switches controlled by a supporting information computer network. Different electrical sensors form an important part of the PPG as well. The paper overviews the PPG as the next power grid evolution step after the Smart Grid. The PPG approach solves a number of problems of open concurrent power market development e.g. highly-efficient energy usage and numerous small sources adoption. The growing Packet Power Grid can play the role of the global power highway the same way as the Internet plays the role of the global information highway.