Jing Shi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jing Shi has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Annan Jiang
College of Transportation Engineering, Dalian Maritime University, Dalian, China
1 shared publication - Bai-Song Li
National-Local Joint Engineering Laboratory of Intelligent Manufacturing Oriented Automobile Die & Mould, Tianjin University of Technology and Education, Tianjin 300222, China
1 shared publication - Jicheng Ding
School of Materials Science and Engineering, Anhui University of Technology, Maanshan 243002, China
1 shared publication - Junxiang Wang
Institute of Road and Bridge Engineering, Dalian Maritime University; 1 Linghai Road, Dalian 116026
1 shared publication - Tie-Gang Wang
Tianjin University of Technology and Education
1 shared publication - Xitong Zhang
National-Local Joint Engineering Laboratory of Intelligent Manufacturing Oriented Automobile Die & Mould, Tianjin University of Technology and Education, Tianjin 300222, China
1 shared publication
Latest Publications
- Open Access
Influence of N2/Ar Flow Ratio on Microstructure and Properties of the AlCrSiN Coatings Deposited by High-Power Impulse Magnetron Sputtering
The cutting properties of tools can be greatly improved by AlCrSiN coatings. The AlCrSiN coatings with nitrogen content in the range of 28.2–56.3 at.% were prepared by varying the N2/Ar flow ratio from 1/4 to 1/1. The influence of N2/Ar flow ratio on composition, microstructure, and mechanical properties, as well as the tribological properties, of the coatings was investigated. With increasing N content, the coating microstructure gradually evolved from single fcc-(Cr,Al)N (200) phase to the mixture of fcc-(Cr,Al)N and hcp-(Cr,Al)N phase, which corresponds to an increased crystallinity within the coatings. The coating presents the highest hardness and best wear resistance for an N2/Ar flow ratio of 1/1, but the film adhesive strength and inner stress decreased obviously with increasing N2/Ar flow ratio, which was attributed to the rapid reduction of particle kinetic energy induced by the obstruction of neutral nitride particles between target and substrates. The highest H3/E*2 value exhibited the lowest wear rate, at 0.81 × 10−14 m3/(N·m), indicating that it had the best resistance to plastic deformation. The main wear mechanisms of the as-deposited coatings were abrasive wear and adhesive wear. The increasing crystallinity of the interior coatings resulted in higher hardness and better tribological behavior with an increase in N2/Ar flow ratio.
Open AccessInfluence of N2/Ar Flow Ratio on Microstructure and Properties of the AlCrSiN Coatings Deposited by High-Power Impulse Magnetron Sputtering
The cutting properties of tools can be greatly improved by AlCrSiN coatings. The AlCrSiN coatings with nitrogen content in the range of 28.2–56.3 at.% were prepared by varying the N2/Ar flow ratio from 1/4 to 1/1. The influence of N2/Ar flow ratio on composition, microstructure, and mechanical properties, as well as the tribological properties, of the coatings was investigated. With increasing N content, the coating microstructure gradually evolved from single fcc-(Cr,Al)N (200) phase to the mixture of fcc-(Cr,Al)N and hcp-(Cr,Al)N phase, which corresponds to an increased crystallinity within the coatings. The coating presents the highest hardness and best wear resistance for an N2/Ar flow ratio of 1/1, but the film adhesive strength and inner stress decreased obviously with increasing N2/Ar flow ratio, which was attributed to the rapid reduction of particle kinetic energy induced by the obstruction of neutral nitride particles between target and substrates. The highest H3/E*2 value exhibited the lowest wear rate, at 0.81 × 10−14 m3/(N·m), indicating that it had the best resistance to plastic deformation. The main wear mechanisms of the as-deposited coatings were abrasive wear and adhesive wear. The increasing crystallinity of the interior coatings resulted in higher hardness and better tribological behavior with an increase in N2/Ar flow ratio.
- 25 July 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 729-733
The Fully Implicit Closest Point Projection Method of the Non-Associative Isotropic Hardening Drucker-Prager Constitutive Model
The fully implicit closest point projection method (CPPM) which avoids the phenomenon of the trial stress drifting from the yield surface is a new numerical integration algorithm. The CPPM has the high accuracy and stability of the numerical solution. The finite element solver is developed based on the elastic-plastic theory and the CPPM of the non-associative isotropic hardening Drucker-Prager constitutive model. The complex geotechnical engineering problem can be solved by the self-developed nonlinear finite element program, then the results show that the accuracy and practicality of the program.
- 25 July 2012
- Published by American Society of Civil Engineers (ASCE)
- p. 729-733
The Fully Implicit Closest Point Projection Method of the Non-Associative Isotropic Hardening Drucker-Prager Constitutive Model
The fully implicit closest point projection method (CPPM) which avoids the phenomenon of the trial stress drifting from the yield surface is a new numerical integration algorithm. The CPPM has the high accuracy and stability of the numerical solution. The finite element solver is developed based on the elastic-plastic theory and the CPPM of the non-associative isotropic hardening Drucker-Prager constitutive model. The complex geotechnical engineering problem can be solved by the self-developed nonlinear finite element program, then the results show that the accuracy and practicality of the program.