Elsayed A. Ashour
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Elsayed A. Ashour has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Nageh K. Allam
Energy Materials Laboratory, School of Sciences and Engineering, The American University in Cairo, New Cairo 11835, Egypt
13 shared publications - Ahmed Abdel Nazeer
Chemistry Department, Faculty of Science, Kuwait University, P.O. Box 5969, Safat 13060, Kuwait
7 shared publications H.S. Hegazy
Physical Chemistry Department, Electrochemistry and Corrosion Lab., National Research Centre, Dokki, Cairo, Egypt
4 shared publicationsB.G. Ateya
Faculty of Science, Chemistry Department, Cairo University, Cairo, Egypt
3 shared publications- Nasser K. Awad
Swinburne University of Technology, Australia
3 shared publications - Abdelaziz S. Fouda
Chemistry Department, Faculty of Science, Mansoura University, Mansoura, Egypt
2 shared publications
Latest Publications
- 1 August 2015
- Published by Elsevier in Applied Surface Science
- Vol. 346, 158-164
Unravelling the composition of the surface layers formed on Cu, Cu-Ni, Cu-Zn and Cu-Ni-Zn in clean and polluted environments
- 1 August 2015
- Published by Elsevier in Applied Surface Science
- Vol. 346, 158-164
Unravelling the composition of the surface layers formed on Cu, Cu-Ni, Cu-Zn and Cu-Ni-Zn in clean and polluted environments
- 1 July 2014
- Published by Elsevier in Applied Surface Science
- Vol. 307, 621-630
Effect of alloying elements on the electrochemical behavior of Cu–Ni–Zn ternary system in sulfide-polluted saltwater
- 1 July 2014
- Published by Elsevier in Applied Surface Science
- Vol. 307, 621-630
Effect of alloying elements on the electrochemical behavior of Cu–Ni–Zn ternary system in sulfide-polluted saltwater
- 1 March 2014
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 6 (2) , 022702
Recent advances in the use of metal oxide-based photocathodes for solar fuel production
Harvesting solar energy for the production of clean fuel by a photoelectrochemical system is a very attractive, yet a challenging task. This review focuses on the recent efforts done to tailor metal oxide-based photocathode materials for the solar-driven hydrogen production. The materials are classified into three categories: simple oxides, complex oxides, and photocathodes used in p-n self-biased heterojunction cells. Generally, three strategies have been recommended to tailor p-type metal oxide semiconductors to meet the requirements for efficient solar-driven water splitting, namely (1) coating the p-type metal oxide either with a protective layer or a dye, (2) using co-catalyst, and (3) merging the p-type material with an n-type photoanode with the proper optical and electrical properties. In the light of those strategies, the optical, structural, and photoelectrochemical characteristics of such assemblies are discussed.
- 1 March 2014
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 6 (2) , 022702
Recent advances in the use of metal oxide-based photocathodes for solar fuel production
Harvesting solar energy for the production of clean fuel by a photoelectrochemical system is a very attractive, yet a challenging task. This review focuses on the recent efforts done to tailor metal oxide-based photocathode materials for the solar-driven hydrogen production. The materials are classified into three categories: simple oxides, complex oxides, and photocathodes used in p-n self-biased heterojunction cells. Generally, three strategies have been recommended to tailor p-type metal oxide semiconductors to meet the requirements for efficient solar-driven water splitting, namely (1) coating the p-type metal oxide either with a protective layer or a dye, (2) using co-catalyst, and (3) merging the p-type material with an n-type photoanode with the proper optical and electrical properties. In the light of those strategies, the optical, structural, and photoelectrochemical characteristics of such assemblies are discussed.
- 1 March 2014
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 144 (1-2) , 55-65
Potential of 5-methyl 1-H benzotriazole to suppress the dissolution of α-aluminum bronze in sulfide-polluted salt water
- 1 March 2014
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 144 (1-2) , 55-65
Potential of 5-methyl 1-H benzotriazole to suppress the dissolution of α-aluminum bronze in sulfide-polluted salt water
- 1 September 2012
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 136 (1) , 1-9
Effect of cysteine on the electrochemical behavior of Cu10Ni alloy in sulfide polluted environments: Experimental and theoretical aspects
- 1 September 2012
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 136 (1) , 1-9
Effect of cysteine on the electrochemical behavior of Cu10Ni alloy in sulfide polluted environments: Experimental and theoretical aspects
- 11 July 2012
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 69 (1) , 77-84
Electrochemical and Stress Corrosion Cracking Behavior of α-Aluminum Bronze and α-Brass in Nitrite Solutions: A Comparative Study
The stress corrosion cracking (SCC) behavior of α-aluminum bronze (Cu7Al) has been investigated in nitrite solution under open circuit and at different anodic potentials and compared to α-brass using the constant slow strain rate technique. The electrochemical behavior was also studied using Tafel and electrochemical frequency modulation (EFM) techniques. While α-brass was quite susceptible to SCC in relatively concentrated sodium nitrate (NaNO2) and highly anodic potentials, α-Al bronze was found to be resistant to SCC. The resistance of α-Al bronze to SCC was attributed to the presence of aluminum oxide (Al2O3) on its surface. Although the time to failure and stress ratio remained virtually constant for α-Al bronze, they decreased sharply with increasing the anodic potential in the case of α-brass. The mode of failure was predominantly ductile for α-Al bronze under various conditions. Previous findings for the change of the mode of failure from intergranular at open-circuit potential to transgranular cracking under anodic potentials were confirmed. The electrochemical corrosion parameters obtained from potentiodynamic polarization and EFM are in good agreement.
- 11 July 2012
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 69 (1) , 77-84
Electrochemical and Stress Corrosion Cracking Behavior of α-Aluminum Bronze and α-Brass in Nitrite Solutions: A Comparative Study
The stress corrosion cracking (SCC) behavior of α-aluminum bronze (Cu7Al) has been investigated in nitrite solution under open circuit and at different anodic potentials and compared to α-brass using the constant slow strain rate technique. The electrochemical behavior was also studied using Tafel and electrochemical frequency modulation (EFM) techniques. While α-brass was quite susceptible to SCC in relatively concentrated sodium nitrate (NaNO2) and highly anodic potentials, α-Al bronze was found to be resistant to SCC. The resistance of α-Al bronze to SCC was attributed to the presence of aluminum oxide (Al2O3) on its surface. Although the time to failure and stress ratio remained virtually constant for α-Al bronze, they decreased sharply with increasing the anodic potential in the case of α-brass. The mode of failure was predominantly ductile for α-Al bronze under various conditions. Previous findings for the change of the mode of failure from intergranular at open-circuit potential to transgranular cracking under anodic potentials were confirmed. The electrochemical corrosion parameters obtained from potentiodynamic polarization and EFM are in good agreement.
- 22 June 2011
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 50 (14) , 8796-8802
Effect of Glycine on the Electrochemical and Stress Corrosion Cracking Behavior of Cu10Ni Alloy in Sulfide Polluted Salt Water
- 22 June 2011
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 50 (14) , 8796-8802
Effect of Glycine on the Electrochemical and Stress Corrosion Cracking Behavior of Cu10Ni Alloy in Sulfide Polluted Salt Water
- 25 March 2011
- Published by Springer Nature in Journal of Solid State Electrochemistry
- Vol. 16 (1) , 353-360
Electrochemical characterization and stress corrosion cracking behavior of α-brass in molybdate-containing electrolytes
- 25 March 2011
- Published by Springer Nature in Journal of Solid State Electrochemistry
- Vol. 16 (1) , 353-360
Electrochemical characterization and stress corrosion cracking behavior of α-brass in molybdate-containing electrolytes
- 24 August 2010
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 49 (19) , 9529-9533
Effect of Annealing on the Stress Corrosion Cracking of α-Brass in Aqueous Electrolytes Containing Aggressive Ions
- 24 August 2010
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 49 (19) , 9529-9533
Effect of Annealing on the Stress Corrosion Cracking of α-Brass in Aqueous Electrolytes Containing Aggressive Ions
- 1 January 2010
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 157 (5) , C174
Adsorption–Desorption Kinetics of Benzotriazole on Cathodically Polarized Copper
- 1 January 2010
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 157 (5) , C174
Adsorption–Desorption Kinetics of Benzotriazole on Cathodically Polarized Copper