LALaura Anania

Laura Anania

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Laura Anania has a total of 25 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Mechanical properties and durability of ancient mortars in the historic buildings of Eastern Sicily

    by Laura Anania, Antonio Badalà

    Eastern Sicily's historic buildings are characterized by an almost uniform use of local and naturally available calcareous and lavic stone as aggregate. Also, ancient mortars comprise of lime or cement-lime binder. Very limited studies concerning the mechanical properties of the ancient mortars have been accomplished. In this paper, mortar samples collected from the surviving heritage masonry structures in eastern Sicily were selected to assess their composition. Due to limitations of dimensions, shape and cohesiveness of mortar samples collected from historic buildings, not laboratory test can be applied on the samples. Then, new mortar samples were constructed matching those of historic buildings in order to determine their mechanical properties. Hence, the restored ancient mortar, were tested after 30-60-90 days of curing and finally after 20 years of curing. The data obtained was, then compared each other. To this aim, two series of mortar were performed for a total of 400 samples. The composition of the mortars differs in according to ancient recipes determined in the laboratory by means of the chemical attack of the samples directly taken from historic buildings. The time effects as well as the aggregate (sand) influence were analyzed. To this aim bending, compression and tensile tests were carried out on all the specimens. The data obtained show after 20 years a reduction between 10 and 15% of the compressive strength in mortar studied. All of these data could be very useful for creating compatible mortar recipes for restoration works as well as to define mechanical features of ancient mortar in modeling process.


  • The effectiveness of FRCM-U-wrap joist: An alternative solution in flexural strengthening of reinforced concrete beams

    by Laura Anania

    This paper presents both experimental and analytical research results for predicting the enhancement of the flexural capacity of reinforced concrete (r.c.) beams strengthened in flexure with an innovative system based on the use of fabric reinforced cementitious matrix (FRCM). The patented system, called FRCM-U-Wrap Joist Tech provides a new methodology for beam strengthening capable of generating a higher internal couple of the cross section with no incisive change of the element weight. Experimental evidence gives back a 100% of increase in flexural strength than the non-reinforced beam. Analytical prediction shows a good accordance with the experimental data. The proposed strengthening system seems to be more effectiveness than the beam strengthened by means of traditional technology consisting in externally bonding the fibers directed to the beam intrados.


  • Numerical validation of double punch test for the assessment of tensile strength in natural fiber reinforced concrete

    by Laura Anania, Giuseppe D'AGata

    In this paper, the results of Finite Element Analysis on concrete specimens reinforced by plant fiber and undergone to double punch tests are presented. In finite element analysis, the constitutive law of the material was calibrated by referring to tensile strength obtained by the Chen formulation and fractural energy derived by the double punch test. The analysis was carried out accounting different volume content of natural fibers derived from a very common plant of Sicily (Agave), to ensure the repeatability of the test. Then, the failure load can be determined by finite element analysis and compared with the experimental one. A good accordance between numerical and experimental data permits us to support the use of the double punch test as a more attractive testing method for the evaluation of the mechanical proprieties of the materials. Double punch test, in fact, is much simpler to perform than the split cylinder test method.


  • Open Access

    Seismic retrofitting of masonry vault using CFRP

    by Laura Anania, Antonio Badalà, Giuseppe D’aGata

    Masonry vaults represent one of the most seismic vulnerable element in an ancient building. It also generally does not possess an adequate capability of redistribution of the seismic action among the walls of the buildings. In this paper, the structural behaviour of a masonry barrel vault strengthened by a new technology in applying Carbon Fiber Reinforced Polymer (C-FRP) is discussed from both theoretical and experimental point of view. The C-FRP is applied such as to assume an Ω shape around a concrete core realized at the vault extrados. This arrangement allows the resulting CFRP reinforced ribbed vault to assume the necessary strength and membranal and flexural rigidity so as to ensure the aforementioned seismic action redistribution capability and to avoid local collapse of the vault. A theoretical prediction of ultimate strength was derived in agreement with the occurrences observed during the experiments (masonry crushing, FRP rupture, debonding, sliding along the mortar joint). To this aim, a novel incremental step-by-step lower bound limit analysis approach was developed taking into account for the shear failure mechanism at each mortar joint. The shear strength is evaluated by the Mohr-Coulomb friction law for the mortar joint and by other nonlinear Italian Code relations for CFRP Ω-Wrap reinforcement. In the approximated incremental analysis process the current value of the shear strength, depend on the compressive stress resulting from the previous step.

  • Open Access

    Numerical simulation of tests for the evaluation of the performance of the reinforced concrete slabs strengthening by FRCM

    by Laura Anania, Antonio Badalá, Giuseppe D’aGata

    In this work the attention is focused to the numerical simulation of the experimental bending tests carried out on a total of six reinforced concrete r.c. plates the latter aimed to provide a basic understanding of the its performance when strengthened by Fiber Reinforced Cementitius Matrix (FRCM) Composites. Three of those were used as control specimens. The numerical simulation was carried out by LUSAS software. A good correlation between the FE results and data obtained from the test, both in the load–deformation behavior and the failure load was highlighted. This permits to prove that applied strengthening system gives back an enhancement 2.5 times greater in respect of the unreinforced case. A greater energy dissipation ability and a residual load-bearing capacity makes the proposed system very useful in the retrofitting as well as in the case of strengthening of bridge structures. Based on the validation of the FE results in bending, the numerical analysis was also extended to characterize the behavior of this strengthening system in tensile.


  • Mechanical characterization of recycled tire rubber to be used as seismic isolation of the structure

    by Laura Anania, Antonio Badalá, Giuseppe D'AGata

    This paper discusses the results obtained by an experimental investigation aimed to the development of an innovative low-cost seismic base isolation pads using scrap car tires. The main idea consists in realizing a new layer, by means of the recycled car tires, that replace large areas of the surrounding soil underneath the structure, or special elastomer based isolator between the soil and the basements. To this aim several tests have been conducted on specimens properly prepared from tires, in order to investigate the behavior of proposed system under compression and shear forces. The results reported here are related to the compression test and they were compared to the ones of common elastomer bearings (SREI). They show that at same strain levels, the instantaneous compression modulus values of RTP specimens are higher than that of the SREI values. The slope changes of RTP specimens start earlier and fail at much lower strains compared to SREI specimen. The high vertical stiffness of RTP layers combined with relatively low amount of steel content makes RTP layers stiffer and lower strength compared to SREI. Test results have shown that the friction between tire layers is sufficient to keep layers intact. RTP application so presents advantages such as low-technology no-cost pad, weight reduction, ease of handling, simple shear stiffness adjustment by changing the number of layers, and environmental benefits by recycling tires.


  • Open Access

    Out of Plane Behavior of Calcareous Masonry Panels Strengthened by CFRP

    by Laura Anania, Giuseppe D’aGata, Cristian Giaquinta, Antonio Badalà


  • Bond Behavior of Standard and Reinforced Anchorage between CFRP Sheet and Natural Calcareous Stone

    by Laura Anania, Antonio Badalà, Giuseppe D’aGata

    In the past two decades, CFRP had been used to strengthen and repair r.c. structures and recently it is also employed to strengthen historical or monumental buildings constituted by masonry structure. However, premature failure due to debonding of the FRP is one of the important issues still to be resolved. Numerous word wide research studies have dealt with the debonding problem in r.c. structures but only a few works were carried out in the masonry structures area. So, the study of the global behaviour of the reinforced masonry element seems to be very useful, both for a congruous design and to verify the strengthening strategy. To this aim, this paper summarizes the debonding phenomena between C-FRP strip and natural calcareous rock brick, employed in our buildings, by means of a testing investigation. Two different kinds of anchorage were designed and employed for the tested samples: standard and reinforced anchorage. The experimental tests carried out on the specimens permits us to compare the effective bond length, with the one obtained by International rules and especially with the Italian CNR-DT200/2004 formulation and to say that the effective bond length dictates by the rules undervalues the experimental data. The data obtained permit us also to know the shear-slip delamination curve useful for the numerical investigation, as well as both the failure mode and the "II mode" fracture energy.