Yuan Xue
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yuan Xue has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Gerhard M. Sessler
Measurement and Sensor Technology Group, Technische Universität Darmstadt 3 , 64283 Darmstadt, Germany
2 shared publications - Mario Kupnik
Measurement and Sensor Technology Group, Technical University of Darmstadt, Darmstadt, Germany
2 shared publications - Xiaoqing Zhang
School of Physics Science and Engineering, Tongji University, Shanghai, China
2 shared publications Gerhard M Sessler
Nachrichtentechnik, Technische Universitaet Darmstadt, Merckstrasse 25, 64283, Darmstadt, 64283 Darmstadt, GERMANY
1 shared publication- Jinfeng Zhao
School of Aerospace Engineering and Applied Mechanics, Tongji University, Shanghai, China
1 shared publication Liming Wu
Tongji University, Shanghai, Shanghai, CHINA
1 shared publication
Latest Publications
- Open Access
- 1 May 2020
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 147 (5) , EL421-EL427
Ferroelectret-based flexible transducers: A strategy for acoustic levitation and manipulation of particles
Advanced acoustic levitation devices featuring flexible, lightweight, wide bandwidth, and film-like transducers based on ferroelectrets are designed and fabricated for sophisticated manipulation of particles in a simple way. Owing to the unique properties of ferroelectret films, such as high piezoelectric activity, very small acoustic impedance, a relatively large damping ratio, flexibility, a large area, and small density, the levitator reported features a wider bandwidth compared to ceramic-based levitators. The transportation of levitated particles is achieved by deformation of the film transducer, which represents a different and promising concept for this task.
- 1 May 2020
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 147 (5) , EL421-EL427
Open AccessFerroelectret-based flexible transducers: A strategy for acoustic levitation and manipulation of particles
Advanced acoustic levitation devices featuring flexible, lightweight, wide bandwidth, and film-like transducers based on ferroelectrets are designed and fabricated for sophisticated manipulation of particles in a simple way. Owing to the unique properties of ferroelectret films, such as high piezoelectric activity, very small acoustic impedance, a relatively large damping ratio, flexibility, a large area, and small density, the levitator reported features a wider bandwidth compared to ceramic-based levitators. The transportation of levitated particles is achieved by deformation of the film transducer, which represents a different and promising concept for this task.
- Open Access
- 11 June 2019
- Published by IOP Publishing in Physica Scripta
- Vol. 94 (9) , 095002
Acoustic energy harvesting with irradiated cross-linked polypropylene piezoelectret films
Piezoelectret films prepared by irradiated cross-linked polypropylene (IXPP) not only feature a large figure of merit (d 33 · g 33, FoM) and a nearly flat response of the sensitivity as a microphone (4 mV Pa−1) in the audio range, but also exhibit a good impedance match to air. Therefore, this material is appropriate for air-coupled sonic and ultrasonic applications. In this work, we report acoustic energy harvesting using IXPP piezoelectret films without mass loading both in ultrasonic and low-frequency ranges. Under an input sound pressure level (SPL) of 100 dB (or 2 Pa) and a resonance frequency of 53 kHz, a maximum output power of 7.2 nW is obtained for an IXPP film harvester. Despite its high resonance frequency, the large FoM of IXPP piezoelectret films suggests itself to be a promising candidate also for low-frequency acoustic energy harvesting with the help of Helmholtz resonators. An output power of 10.3 nW is achieved for a harvester with a 16 cm2 large IXPP film within a Helmholtz resonator, which features a resonance frequency of 900 Hz, with an optimized load resistance of 962 kΩ under an input SPL of 100 dB. In comparison to acoustic energy harvesters based on ferroelectric polymer polyvinylidene fluoride cantilever beams, our devices have much higher output power density under the same conditions and much broader bandwidth. Theoretical analysis and numerical simulations are performed to confirm the experimental results. Moreover, the output power of the IXPP acoustic energy harvesters can be further improved by increasing the active area of the piezoelectret films.
- 11 June 2019
- Published by IOP Publishing in Physica Scripta
- Vol. 94 (9) , 095002
Open AccessAcoustic energy harvesting with irradiated cross-linked polypropylene piezoelectret films
Piezoelectret films prepared by irradiated cross-linked polypropylene (IXPP) not only feature a large figure of merit (d 33 · g 33, FoM) and a nearly flat response of the sensitivity as a microphone (4 mV Pa−1) in the audio range, but also exhibit a good impedance match to air. Therefore, this material is appropriate for air-coupled sonic and ultrasonic applications. In this work, we report acoustic energy harvesting using IXPP piezoelectret films without mass loading both in ultrasonic and low-frequency ranges. Under an input sound pressure level (SPL) of 100 dB (or 2 Pa) and a resonance frequency of 53 kHz, a maximum output power of 7.2 nW is obtained for an IXPP film harvester. Despite its high resonance frequency, the large FoM of IXPP piezoelectret films suggests itself to be a promising candidate also for low-frequency acoustic energy harvesting with the help of Helmholtz resonators. An output power of 10.3 nW is achieved for a harvester with a 16 cm2 large IXPP film within a Helmholtz resonator, which features a resonance frequency of 900 Hz, with an optimized load resistance of 962 kΩ under an input SPL of 100 dB. In comparison to acoustic energy harvesters based on ferroelectric polymer polyvinylidene fluoride cantilever beams, our devices have much higher output power density under the same conditions and much broader bandwidth. Theoretical analysis and numerical simulations are performed to confirm the experimental results. Moreover, the output power of the IXPP acoustic energy harvesters can be further improved by increasing the active area of the piezoelectret films.
- 4 April 2018
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 28 (6) , 065012
Broad bandwidth vibration energy harvester based on thermally stable wavy fluorinated ethylene propylene electret films with negative charges
Wavy fluorinated ethylene propylene (FEP) electret films with negative charges were prepared by a patterning method followed by a corona charging process. The thermal stability of these films was characterized by the surface potential decay with annealing time at elevated temperatures. The results show that thermally stable electret films can be made by corona charging followed by pre-aging treatment. Vibration energy harvesters having a very simple sandwich structure, consisting of a central wavy FEP electret film and two outside metal plates, were designed and their performance, including the resonance frequency, output power, half power bandwidth, and device stability, was investigated. These harvesters show a broad bandwidth as well as high output power. Their performance can be further improved by using a wavy-shaped counter electrode. For an energy harvester with an area of 4 cm 2 and a seismic mass of 80 g, the output power referred to 1 g ( g is the gravity of the earth), the resonance frequency, and the 3 dB bandwidth are 1.85 mW, 90 Hz, and 24 Hz, respectively. The output power is sufficient to power some electronic devices. Such devices may be embedded in shoe soles, carpets or seat cushions where the flexibility is required and large force is available.
- 4 April 2018
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 28 (6) , 065012
Broad bandwidth vibration energy harvester based on thermally stable wavy fluorinated ethylene propylene electret films with negative charges
Wavy fluorinated ethylene propylene (FEP) electret films with negative charges were prepared by a patterning method followed by a corona charging process. The thermal stability of these films was characterized by the surface potential decay with annealing time at elevated temperatures. The results show that thermally stable electret films can be made by corona charging followed by pre-aging treatment. Vibration energy harvesters having a very simple sandwich structure, consisting of a central wavy FEP electret film and two outside metal plates, were designed and their performance, including the resonance frequency, output power, half power bandwidth, and device stability, was investigated. These harvesters show a broad bandwidth as well as high output power. Their performance can be further improved by using a wavy-shaped counter electrode. For an energy harvester with an area of 4 cm 2 and a seismic mass of 80 g, the output power referred to 1 g ( g is the gravity of the earth), the resonance frequency, and the 3 dB bandwidth are 1.85 mW, 90 Hz, and 24 Hz, respectively. The output power is sufficient to power some electronic devices. Such devices may be embedded in shoe soles, carpets or seat cushions where the flexibility is required and large force is available.