Dag Andersson
Research Subjects
Research Interests
Dag Andersson has a total of 123 co-authors. Here are the top co-authors by number of shared publications:
Klas Brinkfeldt
RISE Research Institutes of Sweden, Mlndal, Sweden
9 shared publications- Per-Erik Tegehall
Swerea IVF AB, Argongatan 30, Mölndal, Sweden
8 shared publications Michael Edwards
Chalmers University of Technology, SE-412 96 Göteborg, Sweden
5 shared publicationsOlaf Zschieschang
Fairchild Semicond. GmbH, Aschheim, Germany
5 shared publicationsAlexander Otto
Fraunhofer ENAS, Chemnitz, Germany
4 shared publicationsB. H. Cooper
Laboratory of Atomic and Solid State Physics, Cornell University, Ithaca, New York 14853-2501
4 shared publications
Latest Publications
- 28 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 12 (11) , 1857-1866
Ceramic Additive Manufacturing Potential for Power Electronics Packaging
Compared with silicon-based power devices, wide band gap (WBG) semiconductor devices operate at significantly higher power densities required in applications such as electric vehicles and more electric airplanes. This necessitates development of power electronics packages with enhanced thermal characteristics that fulfil the electrical insulation requirements. The present research investigates the feasibility of using ceramic additive manufacturing (AM), also known as three-dimensional (3D) printing, to address thermal and electrical requirements in packaging gallium nitride (GaN) based high-electron-mobility transistors (HEMTs). The goal is to exploit design freedom and manufacturing flexibility provided by ceramic AM to fabricate power device packages with a lower junction-to-ambient thermal resistance ( R θJA ). Ceramic AM also enables incorporation of intricate 3D features into the package structure in order to control the isolation distance between the package source and drain contact pads. Moreover, AM allows to fabricate different parts of the packaging assembly as a single structure to avoid high thermal resistance interfaces. For example, the ceramic package and the ceramic heatsink can be printed as a single part without any bonding layer. Thermal simulations under different thermal loading and cooling conditions show the improvement of thermal performance of the package fabricated by ceramic AM. If assisted by an efficient cooling strategy, the proposed package has the potential to reduce R θJA by up to 48%. The results of the preliminary efforts to fabricate the ceramic package by AM are presented, and the challenges that have to be overcome for further development of this manufacturing method are recognized and discussed.
- 28 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 12 (11) , 1857-1866
Ceramic Additive Manufacturing Potential for Power Electronics Packaging
Compared with silicon-based power devices, wide band gap (WBG) semiconductor devices operate at significantly higher power densities required in applications such as electric vehicles and more electric airplanes. This necessitates development of power electronics packages with enhanced thermal characteristics that fulfil the electrical insulation requirements. The present research investigates the feasibility of using ceramic additive manufacturing (AM), also known as three-dimensional (3D) printing, to address thermal and electrical requirements in packaging gallium nitride (GaN) based high-electron-mobility transistors (HEMTs). The goal is to exploit design freedom and manufacturing flexibility provided by ceramic AM to fabricate power device packages with a lower junction-to-ambient thermal resistance ( R θJA ). Ceramic AM also enables incorporation of intricate 3D features into the package structure in order to control the isolation distance between the package source and drain contact pads. Moreover, AM allows to fabricate different parts of the packaging assembly as a single structure to avoid high thermal resistance interfaces. For example, the ceramic package and the ceramic heatsink can be printed as a single part without any bonding layer. Thermal simulations under different thermal loading and cooling conditions show the improvement of thermal performance of the package fabricated by ceramic AM. If assisted by an efficient cooling strategy, the proposed package has the potential to reduce R θJA by up to 48%. The results of the preliminary efforts to fabricate the ceramic package by AM are presented, and the challenges that have to be overcome for further development of this manufacturing method are recognized and discussed.
- 1 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-13
On the formation and propagation of laminate cracks and their influence on the fatigue lives of solder joints
Lead-free solder joints have been shown to increase the risk for crack formation in the PCB laminate under the solder pads. As such cracks propagate during thermal cycling, they decrease the strain imposed on the solderjoint by acting as strain relief. In accelerated thermal cycling, these joints have been found to remain virtually undamaged even after a very high number of cycles. If these cracks do not form or propagate to the same extent under milder cycling conditions, typical of service conditions, it may lead to an overestimation of the fatigue life of the solder joints in accelerated testing. In this work, the extent of strain relief and the influence of grain orientations on the initiation and propagation of these cracks are investigated through FE-modelling and compared to what has been experimentally observed for cross-sections of solder joints moulded in epoxy resin with added fluorescent agent and inspected using UV-light and electron backscatter diffraction. Due to the strong anisotropy of lead-free solder joints, the stress transferred to the laminate will vary significantly depending on grain orientation. The presence of these laminate cracks adds another layer of uncertainty to the already complex SnAgCu system, where the strong effects of anisotropy, the continuously evolving secondary precipitate coarsening and its interaction with the recrystallisation process govern the damage evolution. If these effects are not properly accounted for, the interpretation of thermal cycling or modelling and simulation results may be strongly misleading.
- 1 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-13
On the formation and propagation of laminate cracks and their influence on the fatigue lives of solder joints
Lead-free solder joints have been shown to increase the risk for crack formation in the PCB laminate under the solder pads. As such cracks propagate during thermal cycling, they decrease the strain imposed on the solderjoint by acting as strain relief. In accelerated thermal cycling, these joints have been found to remain virtually undamaged even after a very high number of cycles. If these cracks do not form or propagate to the same extent under milder cycling conditions, typical of service conditions, it may lead to an overestimation of the fatigue life of the solder joints in accelerated testing. In this work, the extent of strain relief and the influence of grain orientations on the initiation and propagation of these cracks are investigated through FE-modelling and compared to what has been experimentally observed for cross-sections of solder joints moulded in epoxy resin with added fluorescent agent and inspected using UV-light and electron backscatter diffraction. Due to the strong anisotropy of lead-free solder joints, the stress transferred to the laminate will vary significantly depending on grain orientation. The presence of these laminate cracks adds another layer of uncertainty to the already complex SnAgCu system, where the strong effects of anisotropy, the continuously evolving secondary precipitate coarsening and its interaction with the recrystallisation process govern the damage evolution. If these effects are not properly accounted for, the interpretation of thermal cycling or modelling and simulation results may be strongly misleading.
- 1 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-9
Smart access to small lot manufacturing for systems integration
- 1 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-9
Smart access to small lot manufacturing for systems integration
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 22-30
SMARTER-SI - Smart access to manufacturing for Systems Integration
The three year EU project SMARTER-SI that started in February 2015 has developed and tested a new production platform for smart systems that offer SMEs and “mid-cap” companies help to manufacture small and medium volumes. The ultimate goal of this project is to test a new concept for small lot production, which we call the Cooperative Foundry Model (CFM). The CFM is tested by combining components or parts of systems (building blocks) already developed by the RTOs involved in the project in so-called Application Experiments (AEs), thereby creating innovative Smart Systems which serve SMEs' product needs. During the first two years, four predefined AEs have been developed that consist of i) a multi-parametric point of care testing (POCT) device, ii) a dew-point measurement system, iii) a CO 2 measurement system, and iv) a portable device that can be used to screen water quality.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 22-30
SMARTER-SI - Smart access to manufacturing for Systems Integration
The three year EU project SMARTER-SI that started in February 2015 has developed and tested a new production platform for smart systems that offer SMEs and “mid-cap” companies help to manufacture small and medium volumes. The ultimate goal of this project is to test a new concept for small lot production, which we call the Cooperative Foundry Model (CFM). The CFM is tested by combining components or parts of systems (building blocks) already developed by the RTOs involved in the project in so-called Application Experiments (AEs), thereby creating innovative Smart Systems which serve SMEs' product needs. During the first two years, four predefined AEs have been developed that consist of i) a multi-parametric point of care testing (POCT) device, ii) a dew-point measurement system, iii) a CO 2 measurement system, and iv) a portable device that can be used to screen water quality.
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 25, 1-10
Simulations of the impact of single-grained lead-free solder joints on the reliability of ball Grid Array components
The microstructure of lead-free solder joints often consists of only one or a few randomly oriented tin grains as a result of a large degree of undercooling during solidification. Due to the severe anisotropy of single crystal Sn and the random nature of the microstructure, the stress state and microstructural evolution of each joint will be unique. The orientation of the c-axis of the Sn crystal will strongly affect localized strain induced by temperature cycling, influencing the recrystallization process and thus the damage evolution in the solder joints. This will have strong implications on the reliability of lead-free solder joints and the accuracy of the predictions made with the current standard practices in virtual qualification. As a result of this random distribution of single-grained solder joints, joints to fail first in BGAs are not necessarily only dependent on the distance to neutral point, but rather the combination of location and microstructure of individual joints. In this work, the effect of location and orientation of single-grained solder joints in a CTBGA208 lead-free package were investigated through thermo-mechanical finite-element simulation and were supported by experimental findings of the same package through failure analysis and microstructural investigations using electron backscatter diffraction (EBSD) as well as polarized light microscopy. Due to the lack of data on the material properties of single-grained Sn-based, Pb-free solder joints, the anisotropic elasticity of pure Sn has been combined with the isotropic viscoplastic constitutive models commonly used in the literature.
- 1 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 25, 1-10
Simulations of the impact of single-grained lead-free solder joints on the reliability of ball Grid Array components
The microstructure of lead-free solder joints often consists of only one or a few randomly oriented tin grains as a result of a large degree of undercooling during solidification. Due to the severe anisotropy of single crystal Sn and the random nature of the microstructure, the stress state and microstructural evolution of each joint will be unique. The orientation of the c-axis of the Sn crystal will strongly affect localized strain induced by temperature cycling, influencing the recrystallization process and thus the damage evolution in the solder joints. This will have strong implications on the reliability of lead-free solder joints and the accuracy of the predictions made with the current standard practices in virtual qualification. As a result of this random distribution of single-grained solder joints, joints to fail first in BGAs are not necessarily only dependent on the distance to neutral point, but rather the combination of location and microstructure of individual joints. In this work, the effect of location and orientation of single-grained solder joints in a CTBGA208 lead-free package were investigated through thermo-mechanical finite-element simulation and were supported by experimental findings of the same package through failure analysis and microstructural investigations using electron backscatter diffraction (EBSD) as well as polarized light microscopy. Due to the lack of data on the material properties of single-grained Sn-based, Pb-free solder joints, the anisotropic elasticity of pure Sn has been combined with the isotropic viscoplastic constitutive models commonly used in the literature.
- 18 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1415-1422
Thermal Simulations and Experimental Verification of Power Modules Designed for Double Sided Cooling
Cooling power modules on both sides of the active switching devices reduces the operational junction temperature compared to conventional single sided cooling. In this work, thermal simulations of power modules based on single sided cooling concepts are compared with double sided cooling counterparts. Expected junction temperatures, maximum temperatures and maximum current capability is analyzed. In addition, experimental verification in the form of comparisons with thermal characterization tests for both single-and double sided power modules based on SiC bipolar junction transistors is presented. Results from simulations show that cooling of both sides of the active switching devices can reduce the thermal resistance by more than 40 percent. This number depends on the heat transfer coefficient. From one example, simulating a worst case stall condition of the electric machine, the use of double sided cooling reduces the maximum junction temperature from 167 °C to 106 °C at a load current of 300 A using a heat transfer coefficient of 4 kW/m2K and 4 kHz switching frequency. Furthermore, the temperature decreases to 97 °C if AlN-based DBC substrates are used instead of alumina DBCs. Results from the experimental comparison between double-and single sided cooling showed that the maximum temperature for a load current range of 15 A to 50 A was reduced by 18 percent to 55 percent by using double sided cooling. At a device temperature of 60 °C, the increased thermal capability of the double sided version allowed for a 20 A higher load current, which corresponded to operation under 50 percent higher power losses. Double sided cooling also increased the maximum current capability through a single SiC BJT by more than 20 percent beyond the maximum current capability through the single sided cooling version.
- 18 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1415-1422
Thermal Simulations and Experimental Verification of Power Modules Designed for Double Sided Cooling
Cooling power modules on both sides of the active switching devices reduces the operational junction temperature compared to conventional single sided cooling. In this work, thermal simulations of power modules based on single sided cooling concepts are compared with double sided cooling counterparts. Expected junction temperatures, maximum temperatures and maximum current capability is analyzed. In addition, experimental verification in the form of comparisons with thermal characterization tests for both single-and double sided power modules based on SiC bipolar junction transistors is presented. Results from simulations show that cooling of both sides of the active switching devices can reduce the thermal resistance by more than 40 percent. This number depends on the heat transfer coefficient. From one example, simulating a worst case stall condition of the electric machine, the use of double sided cooling reduces the maximum junction temperature from 167 °C to 106 °C at a load current of 300 A using a heat transfer coefficient of 4 kW/m2K and 4 kHz switching frequency. Furthermore, the temperature decreases to 97 °C if AlN-based DBC substrates are used instead of alumina DBCs. Results from the experimental comparison between double-and single sided cooling showed that the maximum temperature for a load current range of 15 A to 50 A was reduced by 18 percent to 55 percent by using double sided cooling. At a device temperature of 60 °C, the increased thermal capability of the double sided version allowed for a 20 A higher load current, which corresponded to operation under 50 percent higher power losses. Double sided cooling also increased the maximum current capability through a single SiC BJT by more than 20 percent beyond the maximum current capability through the single sided cooling version.
- 1 January 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
COSIVU — Compact, smart and reliable drive unit for fully electric vehicles
COSIVU is a three year collaborative research project that ended in September 2015 and which has been funded within the European Green Car Initiative (now the European Green Vehicle Initiative). COSIVU addresses one of the most critical technical parts in fully electrical vehicles (FEV) besides the energy storage system: the mechatronic drive-train unit. The COSIVU project has delivered a new system architecture for multiple wheel drive-trains by a smart, compact and durable single-wheel drive unit with integrated electric motor, full silicon carbide (SiC) power electronics (switches and diodes), a novel control and health monitoring module with wireless communication, and an advanced ultra-compact cooling solution. DfR utilizing FEM simulations ensures first time right solutions. This paper presents the main results including the architecture of the drive train solution as well as the modular design of the inverter based on Inverter Building Blocks, one per phase. Performance tests are presented here for the first time for both the heavy duty commercial vehicle solution performed in a test rig by Volvo, and the tests of the COSIVU solution adapted to a passenger car done by Elaphe.
- 1 January 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
COSIVU — Compact, smart and reliable drive unit for fully electric vehicles
COSIVU is a three year collaborative research project that ended in September 2015 and which has been funded within the European Green Car Initiative (now the European Green Vehicle Initiative). COSIVU addresses one of the most critical technical parts in fully electrical vehicles (FEV) besides the energy storage system: the mechatronic drive-train unit. The COSIVU project has delivered a new system architecture for multiple wheel drive-trains by a smart, compact and durable single-wheel drive unit with integrated electric motor, full silicon carbide (SiC) power electronics (switches and diodes), a novel control and health monitoring module with wireless communication, and an advanced ultra-compact cooling solution. DfR utilizing FEM simulations ensures first time right solutions. This paper presents the main results including the architecture of the drive train solution as well as the modular design of the inverter based on Inverter Building Blocks, one per phase. Performance tests are presented here for the first time for both the heavy duty commercial vehicle solution performed in a test rig by Volvo, and the tests of the COSIVU solution adapted to a passenger car done by Elaphe.
- 1 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Thermo-mechanical simulations of SiC power modules with single and double sided cooling
Effectively removing dissipated heat from the switching devices enables a higher current carrying capability per chip area ratio, thus leading to smaller or fewer devices for a given power requirement specification. Further, the use of SiC based devices has proven to increase the efficiency of the system thereby reducing the dissipated heat. Thermal models have been used to compare SiC power modules. Single and double sided cooling have been simulated. The simulated maximum temperatures were 141 °C for the single sided version and 119.7 °C for the double sided version. In addition, the reliability of a single sided module and thermally induced plastic strains of a double sided module have been investigated. A local model of the wire bond interface to the transistor metallization shows a 3 0 / 00 maximum increase in plastic strain during the power cycle. Simulations of the creep strain rates in the die attach solder layer for a power cycling loads also shows a 3 0 / 00 increase in creep strain per cycle.
- 1 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Thermo-mechanical simulations of SiC power modules with single and double sided cooling
Effectively removing dissipated heat from the switching devices enables a higher current carrying capability per chip area ratio, thus leading to smaller or fewer devices for a given power requirement specification. Further, the use of SiC based devices has proven to increase the efficiency of the system thereby reducing the dissipated heat. Thermal models have been used to compare SiC power modules. Single and double sided cooling have been simulated. The simulated maximum temperatures were 141 °C for the single sided version and 119.7 °C for the double sided version. In addition, the reliability of a single sided module and thermally induced plastic strains of a double sided module have been investigated. A local model of the wire bond interface to the transistor metallization shows a 3 0 / 00 maximum increase in plastic strain during the power cycle. Simulations of the creep strain rates in the die attach solder layer for a power cycling loads also shows a 3 0 / 00 increase in creep strain per cycle.