Felipe Rebelo Lopes
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Felipe Rebelo Lopes has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Antonio W.C. Do Lago
1 shared publication- Daniel H. Braz de Sousa
Military Institute of Engineering, Rio de Janeiro, Brazil
1 shared publication - Helon Vicente Hultmann Ayala
Department of Mechanical Engineering, Pontifical Catholic University of Paran, Rio de Janeiro, Brazil
1 shared publication Jorge Audrin Morgado de Gois
Military Institute of Engineering
1 shared publicationMarco A. Meggiolaro
1 shared publication- Marco Antonio Meggiolaro
PUC-Rio
1 shared publication
Latest Publications
- Open Access
- 22 January 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (3) , 1076
Assessment of Fatigue Life and Failure Criteria in Ultrasonic Testing Through Thermal Analyses
An experimental study was conducted to analyze temperature evolution during very high cycle fatigue tests. The temperature–number of cycles (T–N) curve is typically divided into three phases: Phase I—a rapid temperature increases at the start of the test, Phase II—temperature stabilization, and Phase III—a sharp temperature rise at the test’s end, coinciding with specimen fracture. The high frequencies used in ultrasonic fatigue testing can induce self-heating in specimens, but the thermal effects are not yet fully understood. Temperature is known to influence the fatigue performance of materials. To explore this, specimens were subjected to varying stress levels and intermittent loading conditions while monitoring temperature evolution using infrared thermography. The T–N curves were obtained, and S–N curves were constructed for specimens tested at room temperature. All tests were performed under fully reversed loading conditions. The experimental data were used to evaluate models commonly applied in conventional fatigue testing. Additionally, the temperature gradient at the beginning of the ultrasonic fatigue test and the heat dissipation per cycle were estimated and analyzed as potential fatigue damage parameters. These findings indicate that parameters derived from the T–N curve have significant potential for predicting very high cycle fatigue life.
- 22 January 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (3) , 1076
Open AccessAssessment of Fatigue Life and Failure Criteria in Ultrasonic Testing Through Thermal Analyses
An experimental study was conducted to analyze temperature evolution during very high cycle fatigue tests. The temperature–number of cycles (T–N) curve is typically divided into three phases: Phase I—a rapid temperature increases at the start of the test, Phase II—temperature stabilization, and Phase III—a sharp temperature rise at the test’s end, coinciding with specimen fracture. The high frequencies used in ultrasonic fatigue testing can induce self-heating in specimens, but the thermal effects are not yet fully understood. Temperature is known to influence the fatigue performance of materials. To explore this, specimens were subjected to varying stress levels and intermittent loading conditions while monitoring temperature evolution using infrared thermography. The T–N curves were obtained, and S–N curves were constructed for specimens tested at room temperature. All tests were performed under fully reversed loading conditions. The experimental data were used to evaluate models commonly applied in conventional fatigue testing. Additionally, the temperature gradient at the beginning of the ultrasonic fatigue test and the heat dissipation per cycle were estimated and analyzed as potential fatigue damage parameters. These findings indicate that parameters derived from the T–N curve have significant potential for predicting very high cycle fatigue life.
- Open Access
- 7 December 2020
- Published by Sociedade Brasileira de Automatica
- Vol. 2 (1)
Modeling and Control of Four-bar Mechanism with Series Elastic Actuators
A new generation of robots that work in cooperation with humans (called collaborative robots) needs some flexibility to adapt to the environment and activities with people. That is why the Series Elastic Actuator (SEA) has been a breakthrough in actuator technologies. The idea of inserting an elastic element in series with a motor allows a lower output impedance, consequently a flexible behavior in the manipulator, in addition to providing torque feedback to better compensate disturbances caused e.g. by friction losses. This article presents a four-bar mechanism with SEA for the purpose of robotic manipulation. Its kinematics and dynamicsare studied, as well as its regulation and trajectory control. The behavior of the decoupled four-bar mechanism and the characteristics of the SEA are also analyzed. Then the regulation control of the complete system is carried out using LQR control. Finally, a circular trajectory is controlled in a simulation to validate the proposed control strategy. The simulation results show the effectiveness of the proposed controller for the mechanism in the presence of SEAs estimating torque and providing the desired compliance for human interaction.
- 7 December 2020
- Published by Sociedade Brasileira de Automatica
- Vol. 2 (1)
Open AccessModeling and Control of Four-bar Mechanism with Series Elastic Actuators
A new generation of robots that work in cooperation with humans (called collaborative robots) needs some flexibility to adapt to the environment and activities with people. That is why the Series Elastic Actuator (SEA) has been a breakthrough in actuator technologies. The idea of inserting an elastic element in series with a motor allows a lower output impedance, consequently a flexible behavior in the manipulator, in addition to providing torque feedback to better compensate disturbances caused e.g. by friction losses. This article presents a four-bar mechanism with SEA for the purpose of robotic manipulation. Its kinematics and dynamicsare studied, as well as its regulation and trajectory control. The behavior of the decoupled four-bar mechanism and the characteristics of the SEA are also analyzed. Then the regulation control of the complete system is carried out using LQR control. Finally, a circular trajectory is controlled in a simulation to validate the proposed control strategy. The simulation results show the effectiveness of the proposed controller for the mechanism in the presence of SEAs estimating torque and providing the desired compliance for human interaction.
- 27 July 2018
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 40 (8) , 399
ECG model parameters optimization and space state reconstruction
- 27 July 2018
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 40 (8) , 399
ECG model parameters optimization and space state reconstruction