Josep Virgili-Llop
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Josep Virgili-Llop has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Marcello Romano
Mechanical and Aerospace Engineering Department, Naval Postgraduate School, Monterey, CA, USA
4 shared publications- Peter C. E. Roberts
The University of Manchester, Manchester, UK
4 shared publications Costantinos Zagaris
Mechanical and Aerospace Engineering Department, Naval Postgraduate School, Monterey, CA, USA
3 shared publicationsRichard Zappulla
Mechanical and Aerospace Engineering Department, Naval Postgraduate School, Monterey, CA, USA
3 shared publicationsHyeongjun Park
Naval Postgraduate School
2 shared publications- Richard Zappulla
Mechanical and Aerospace Engineering Department, Naval Postgraduate School, Monterey, CA 93943 USA
2 shared publications
Latest Publications
- 10 December 2018
- Published by SAGE Publications in The International Journal of Robotics Research
- Vol. 38 (1) , 40-72
A convex-programming-based guidance algorithm to capture a tumbling object on orbit using a spacecraft equipped with a robotic manipulator
An algorithm to guide the capture of a tumbling resident space object by a spacecraft equipped with a robotic manipulator is presented. A solution to the guidance problem is found by solving a collection of convex programming problems. As convex programming offers deterministic convergence properties, this algorithm is suitable for onboard implementation and real-time use. A set of hardware-in-the-loop experiments substantiates this claim. To cast the guidance problem as a collection of convex programming problems, the capture maneuver is divided into two simultaneously occurring sub-maneuvers: a system-wide translation and an internal re-configuration. These two sub-maneuvers are optimized in two consecutive steps. A sequential convex programming procedure, overcoming the presence of non-convex constraints and nonlinear dynamics, is used on both optimization steps. A proof of convergence is offered for the system-wide translation, while a set of structured heuristics—trust regions—is used for the optimization of the internal re-configuration sub-maneuver. Videos of the numerically simulated and experimentally demonstrated maneuvers are included as supplementary material.
- 10 December 2018
- Published by SAGE Publications in The International Journal of Robotics Research
- Vol. 38 (1) , 40-72
A convex-programming-based guidance algorithm to capture a tumbling object on orbit using a spacecraft equipped with a robotic manipulator
An algorithm to guide the capture of a tumbling resident space object by a spacecraft equipped with a robotic manipulator is presented. A solution to the guidance problem is found by solving a collection of convex programming problems. As convex programming offers deterministic convergence properties, this algorithm is suitable for onboard implementation and real-time use. A set of hardware-in-the-loop experiments substantiates this claim. To cast the guidance problem as a collection of convex programming problems, the capture maneuver is divided into two simultaneously occurring sub-maneuvers: a system-wide translation and an internal re-configuration. These two sub-maneuvers are optimized in two consecutive steps. A sequential convex programming procedure, overcoming the presence of non-convex constraints and nonlinear dynamics, is used on both optimization steps. A proof of convergence is offered for the system-wide translation, while a set of structured heuristics—trust regions—is used for the optimization of the internal re-configuration sub-maneuver. Videos of the numerically simulated and experimentally demonstrated maneuvers are included as supplementary material.
- 24 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Control Systems Technology
- Vol. 27 (6) , 2598-2605
Real-Time Autonomous Spacecraft Proximity Maneuvers and Docking Using an Adaptive Artificial Potential Field Approach
In an effort to pursue more advanced missions in space, improved on-board trajectory optimization and path (re)planning capabilities are necessary. Over the past decades, numerous missions have pushed the state of the art in autonomous rendezvous and proximity operations (RPOs). Regardless of the mission, any RPO guidance algorithm must be able to react to a dynamic environment while generating a fuel-efficient trajectory. An adaptive artificial potential function (AAPF) guidance exhibiting these properties has been experimentally evaluated on a spacecraft air-bearing test bed and its performance compared to traditional APF and other real-time guidance methods.
- 24 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Control Systems Technology
- Vol. 27 (6) , 2598-2605
Real-Time Autonomous Spacecraft Proximity Maneuvers and Docking Using an Adaptive Artificial Potential Field Approach
In an effort to pursue more advanced missions in space, improved on-board trajectory optimization and path (re)planning capabilities are necessary. Over the past decades, numerous missions have pushed the state of the art in autonomous rendezvous and proximity operations (RPOs). Regardless of the mission, any RPO guidance algorithm must be able to react to a dynamic environment while generating a fuel-efficient trajectory. An adaptive artificial potential function (AAPF) guidance exhibiting these properties has been experimentally evaluated on a spacecraft air-bearing test bed and its performance compared to traditional APF and other real-time guidance methods.
- 9 June 2017
- Published by Springer Nature in CEAS Space Journal
- Vol. 10 (1) , 101-113
Using the attitude response of aerostable spacecraft to measure thermospheric wind
- 9 June 2017
- Published by Springer Nature in CEAS Space Journal
- Vol. 10 (1) , 101-113
Using the attitude response of aerostable spacecraft to measure thermospheric wind
- 22 May 2017
- Published by Springer Nature in CEAS Space Journal
- Vol. 10 (1) , 37-49
Experimental evaluation of model predictive control and inverse dynamics control for spacecraft proximity and docking maneuvers
- 22 May 2017
- Published by Springer Nature in CEAS Space Journal
- Vol. 10 (1) , 37-49
Experimental evaluation of model predictive control and inverse dynamics control for spacecraft proximity and docking maneuvers
- 9 September 2016
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Floating Spacecraft Simulator Test Bed for the Experimental Testing of Autonomous Guidance, Navigation, & Control of Spacecraft Proximity Maneuvers and Operations
AIAA/AAS Astrodynamics Specialist Conference, Long Beach, CA. The article of record may be found at: http://arc.aiaa.org | DOI: 10.2514/6.2016-5268Ground-based test beds are critical to develop and test different elements of spacecraft guidance, navigation and control subsystems. This paper provides an in-detail description of the state-of-the-art NPS POSEIDYN air bearing test bed used to develop, in a simulated weightless and frictionless enviornment, guidance, navigation and control methods for close proximity operations. Test vehicles, representing spacecraft, use air bearings to float on top of a horizontally leveled granite monolith. This set-up achieves a quasi-frictionless and low residual acceleration dynamic environment. The test bed experimental set-up as well as the vehicles hardware and software architectures are discussed in detail. Characterization of different test bed elements is provided. Finally, a test campaign is used to showcase its capabilities and to illustrate the test bed operations
- 9 September 2016
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Floating Spacecraft Simulator Test Bed for the Experimental Testing of Autonomous Guidance, Navigation, & Control of Spacecraft Proximity Maneuvers and Operations
AIAA/AAS Astrodynamics Specialist Conference, Long Beach, CA. The article of record may be found at: http://arc.aiaa.org | DOI: 10.2514/6.2016-5268Ground-based test beds are critical to develop and test different elements of spacecraft guidance, navigation and control subsystems. This paper provides an in-detail description of the state-of-the-art NPS POSEIDYN air bearing test bed used to develop, in a simulated weightless and frictionless enviornment, guidance, navigation and control methods for close proximity operations. Test vehicles, representing spacecraft, use air bearings to float on top of a horizontally leveled granite monolith. This set-up achieves a quasi-frictionless and low residual acceleration dynamic environment. The test bed experimental set-up as well as the vehicles hardware and software architectures are discussed in detail. Characterization of different test bed elements is provided. Finally, a test campaign is used to showcase its capabilities and to illustrate the test bed operations
- 1 May 2015
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Guidance, Control, and Dynamics
- Vol. 38 (5) , 831-842
Descending Sun-Synchronous Orbits with Aerodynamic Inclination Correction
Earth observation spacecraft use sun-synchronous orbits because they enable observations of ground targets with similar illumination conditions over different passes. To achieve these orbits, spacecraft shall be orbiting the Earth at a particular inclination, which is a function of the orbiting altitude. In the low-Earth-orbit range, spacecraft experience aerodynamic drag, which makes the spacecraft orbit decay while the orbit inclination remains unchanged, hence loosing the sun-synchronous aspect of the orbit if no corrective measures are taken. A novel method is proposed whereby the sun-synchronous inclination is maintained, using aerodynamic lift, while the spacecraft decays due to aerodynamic drag. To achieve it, a lift-to-drag ratio in the range of 1.0–1.6 is required. This lift-to-drag ratio is not feasible with currently characterized surface properties but it may be achievable in the future. To apply this method in the present, propulsion that partially compensates the drag would be required to lo...
- 1 May 2015
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Guidance, Control, and Dynamics
- Vol. 38 (5) , 831-842
Descending Sun-Synchronous Orbits with Aerodynamic Inclination Correction
Earth observation spacecraft use sun-synchronous orbits because they enable observations of ground targets with similar illumination conditions over different passes. To achieve these orbits, spacecraft shall be orbiting the Earth at a particular inclination, which is a function of the orbiting altitude. In the low-Earth-orbit range, spacecraft experience aerodynamic drag, which makes the spacecraft orbit decay while the orbit inclination remains unchanged, hence loosing the sun-synchronous aspect of the orbit if no corrective measures are taken. A novel method is proposed whereby the sun-synchronous inclination is maintained, using aerodynamic lift, while the spacecraft decays due to aerodynamic drag. To achieve it, a lift-to-drag ratio in the range of 1.0–1.6 is required. This lift-to-drag ratio is not feasible with currently characterized surface properties but it may be achievable in the future. To apply this method in the present, propulsion that partially compensates the drag would be required to lo...
- 1 March 2015
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Guidance, Control, and Dynamics
- Vol. 38 (3) , 403-413
Atmospheric Interface Reentry Point Targeting Using Aerodynamic Drag Control
The ability to control the location of a spacecraft atmospheric interface reentry has been traditionally accomplished using propulsion. A novel technique is presented here where a predefined point of atmospheric interface reentry is achieved by adjusting the aerodynamic drag of a spacecraft in a circular orbit. If this method is employed at a sufficiently high starting altitude, any ground-track point accessible by the orbit can be targeted. This method can be broken up into two different parts. The first consists of finding the decay profile that achieves the desired reentry location. The second consists of keeping the spacecraft within this nominal decay trajectory, given the atmospheric uncertainty and other perturbations. The two parts of this method are presented here in detail. Finally, a case study is provided to demonstrate how this method could work in a realistic scenario and to evaluate its performance. The case study shows that a reentry point can be targeted with a 3σ error of less than 200 k...
- 1 March 2015
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Guidance, Control, and Dynamics
- Vol. 38 (3) , 403-413
Atmospheric Interface Reentry Point Targeting Using Aerodynamic Drag Control
The ability to control the location of a spacecraft atmospheric interface reentry has been traditionally accomplished using propulsion. A novel technique is presented here where a predefined point of atmospheric interface reentry is achieved by adjusting the aerodynamic drag of a spacecraft in a circular orbit. If this method is employed at a sufficiently high starting altitude, any ground-track point accessible by the orbit can be targeted. This method can be broken up into two different parts. The first consists of finding the decay profile that achieves the desired reentry location. The second consists of keeping the spacecraft within this nominal decay trajectory, given the atmospheric uncertainty and other perturbations. The two parts of this method are presented here in detail. Finally, a case study is provided to demonstrate how this method could work in a realistic scenario and to evaluate its performance. The case study shows that a reentry point can be targeted with a 3σ error of less than 200 k...
- 1 July 2014
- Published by Elsevier in Acta Astronautica
- Vol. 100, 82-93
Use of CYPRES™ cutters with a Kevlar clamp band for hold-down and release of the Icarus De-Orbit Sail payload on TechDemoSat-1
- 1 July 2014
- Published by Elsevier in Acta Astronautica
- Vol. 100, 82-93
Use of CYPRES™ cutters with a Kevlar clamp band for hold-down and release of the Icarus De-Orbit Sail payload on TechDemoSat-1
- 1 August 2013
- Published by Elsevier in Acta Astronautica
- Vol. 89, 130-138
, a QB50 CubeSat mission to study rarefied-gas drag modelling- 1 August 2013
- Published by Elsevier in Acta Astronautica
- Vol. 89, 130-138
, a QB50 CubeSat mission to study rarefied-gas drag modelling