Le Huong Nguyen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Le Huong Nguyen has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
G. Gobsch
Institute of Physics, Experimental Physics I, Technical University of Ilmenau, Weimarer Str. 32, 98693 Ilmenau (Germany)
1 shared publication- Harald Hoppe
Laboratory of Organic and Macromolecular Chemistry (IOMC) Friedrich Schiller University Jena Jena Germany
1 shared publication M. Gu
Centre for Micro-Photonics & Centre for Ultrahigh-bandwidth Devices for Optical Systems (CUDOS), School of Biophysical Sciences and Electrical Engineering, Mail 31, Swinburne University of Technology, PO Box 218, Hawthorn, Victoria 3122, Australia
1 shared publicationM. Straub
Centre for Micro-Photonics & Centre for Ultrahigh-bandwidth Devices for Optical Systems (CUDOS), School of Biophysical Sciences and Electrical Engineering, Mail 31, Swinburne University of Technology, PO Box 218, Hawthorn, Victoria 3122, Australia
1 shared publicationMin Gu
Centre for Micro-Photonics & Centre for Ultrahigh-bandwidth Devices for Optical Systems, Faculty of Engineering and Industrial Sciences, Swinburne University of Technology, P.O. Box 218, Hawthorn, Victoria 3122, Australia
1 shared publication- Niyazi Serdar Sariciftci
Linz Institute for Organic Solar Cells (LIOS), Institute of Physical Chemistry, Johannes Kepler University Linz, Altenberger Str. 69, 4040, Linz, Austria
1 shared publication
Latest Publications
- 12 March 2007
- Published by Wiley in Advanced Functional Materials
- Vol. 17 (7) , 1071-1078
Effects of Annealing on the Nanomorphology and Performance of Poly(alkylthiophene):Fullerene Bulk‐Heterojunction Solar Cells
The evolution of nanomorphology within thin solid‐state films of poly(3‐alkylthiophene):[6,6]‐phenyl‐C61 butyric acid methyl ester (P3AT:PCBM) blends during the film formation and subsequent thermal annealing is reported. In detail, the influence of the P3AT's alkyl side chain length on the polymer/fullerene phase separation is discussed. Butyl, hexyl, octyl, decyl, and dodecyl side groups are investigated. All of the P3ATs used were regioregular. To elucidate the nanomorphology, atomic force microscopy (AFM), X‐ray diffraction, and optical spectroscopy are applied. Furthermore, photovoltaic devices of each of the different P3ATs have been constructed, characterized, and correlated with the nanostructure of the blends. It is proposed that the thermal‐annealing step, commonly applied to these P3AT:PCBM blend films, controls two main issues at the same time: a) the crystallization of P3AT and b) the phase separation and diffusion of PCBM. The results show that PCBM diffusion is the main limiting process for reaching high device performances.
- 12 March 2007
- Published by Wiley in Advanced Functional Materials
- Vol. 17 (7) , 1071-1078
Effects of Annealing on the Nanomorphology and Performance of Poly(alkylthiophene):Fullerene Bulk‐Heterojunction Solar Cells
The evolution of nanomorphology within thin solid‐state films of poly(3‐alkylthiophene):[6,6]‐phenyl‐C61 butyric acid methyl ester (P3AT:PCBM) blends during the film formation and subsequent thermal annealing is reported. In detail, the influence of the P3AT's alkyl side chain length on the polymer/fullerene phase separation is discussed. Butyl, hexyl, octyl, decyl, and dodecyl side groups are investigated. All of the P3ATs used were regioregular. To elucidate the nanomorphology, atomic force microscopy (AFM), X‐ray diffraction, and optical spectroscopy are applied. Furthermore, photovoltaic devices of each of the different P3ATs have been constructed, characterized, and correlated with the nanostructure of the blends. It is proposed that the thermal‐annealing step, commonly applied to these P3AT:PCBM blend films, controls two main issues at the same time: a) the crystallization of P3AT and b) the phase separation and diffusion of PCBM. The results show that PCBM diffusion is the main limiting process for reaching high device performances.
- 11 August 2005
- Published by Wiley in Macromolecular Chemistry and Physics
- Vol. 206 (16) , 1659-1664
Decomposition Kinetics, Life Estimation, and Dielectric Study of an Acrylate based Photopolymer for Microfabrication and Photonic Applications
Summary: Kinetics of thermal decomposition of the acrylate‐based photopolymer LN1 for microfabrication was studied with dynamic thermogravimetric analysis experiments. The kinetic parameters including the activation energy, pre‐exponential factor, and rate constant, which were calculated by the Flynn and Wall method, are presented. The results indicate that thermal degradation of the material consists of three distinct reaction stages. A mechanism of thermal decomposition was proposed, which is in good agreement with the experimental results. The lifetime of the material was estimated by the method of Toop, giving the key information for microelectronics and photonic applications. In addition, the curing behavior of the system was studied by dielectric analysis providing valuable information for processing and fabrication control. Conversion time versus temperature (a), percentage conversion versus time (b). image Conversion time versus temperature (a), percentage conversion versus time (b).
- 11 August 2005
- Published by Wiley in Macromolecular Chemistry and Physics
- Vol. 206 (16) , 1659-1664
Decomposition Kinetics, Life Estimation, and Dielectric Study of an Acrylate based Photopolymer for Microfabrication and Photonic Applications
Summary: Kinetics of thermal decomposition of the acrylate‐based photopolymer LN1 for microfabrication was studied with dynamic thermogravimetric analysis experiments. The kinetic parameters including the activation energy, pre‐exponential factor, and rate constant, which were calculated by the Flynn and Wall method, are presented. The results indicate that thermal degradation of the material consists of three distinct reaction stages. A mechanism of thermal decomposition was proposed, which is in good agreement with the experimental results. The lifetime of the material was estimated by the method of Toop, giving the key information for microelectronics and photonic applications. In addition, the curing behavior of the system was studied by dielectric analysis providing valuable information for processing and fabrication control. Conversion time versus temperature (a), percentage conversion versus time (b). image Conversion time versus temperature (a), percentage conversion versus time (b).
- 14 February 2005
- Published by Wiley in Advanced Functional Materials
- Vol. 15 (2) , 209-216
Acrylate‐Based Photopolymer for Two‐Photon Microfabrication and Photonic Applications
This paper provides a photopolymerizing material suitable for stereolithography of complex submicrometer‐sized three‐dimensional (3D) structural elements to a broad scientific public. Here, we present the formulation of a polymer (LN1 resin) that allows further research in the field of nanofabrication and ‐technology as it surpasses current material limitations. The polymer consists of multifunctional acrylate oligomers as binder, polyfunctional monomers, and a photoinitiator (PI). The chemistry to form 3D structures is based on photopolymerization of the acrylate system initiated by free‐radical species that are triggered by two‐photon absorption of a PI. Important parameters of photocuring, such as the effects of PI concentration, temperature, and light intensity, were studied using photocalorimetry. The thermal stability of the material was tested using thermal gravimetric analysis, providing key information for electronic and photonic applications. Photonic‐crystal structures generated from this resin exhibiting photonic stop gaps in near‐infrared‐ and telecommunication‐wavelength regions are presented.
- 14 February 2005
- Published by Wiley in Advanced Functional Materials
- Vol. 15 (2) , 209-216
Acrylate‐Based Photopolymer for Two‐Photon Microfabrication and Photonic Applications
This paper provides a photopolymerizing material suitable for stereolithography of complex submicrometer‐sized three‐dimensional (3D) structural elements to a broad scientific public. Here, we present the formulation of a polymer (LN1 resin) that allows further research in the field of nanofabrication and ‐technology as it surpasses current material limitations. The polymer consists of multifunctional acrylate oligomers as binder, polyfunctional monomers, and a photoinitiator (PI). The chemistry to form 3D structures is based on photopolymerization of the acrylate system initiated by free‐radical species that are triggered by two‐photon absorption of a PI. Important parameters of photocuring, such as the effects of PI concentration, temperature, and light intensity, were studied using photocalorimetry. The thermal stability of the material was tested using thermal gravimetric analysis, providing key information for electronic and photonic applications. Photonic‐crystal structures generated from this resin exhibiting photonic stop gaps in near‐infrared‐ and telecommunication‐wavelength regions are presented.