Roustiam Chakirov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Roustiam Chakirov has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Yuriy Vagapov
Faculty of Arts, Computing and Engineering, Wrexham University, Wrexham, U.K.
11 shared publications - Sergey Lupin
National Research University of Electronic Technology, Zelenograd, Moscow, Russia
6 shared publications - Oleksandr Veligorskyi
Chernihiv Polytechnic National University
4 shared publications Anastasia Davydova
Department of Computer Science, National Research University of Electronic Technology, Zelenograd, Moscow, 124498, Russia
2 shared publications- Maksym Khomenko
PhD in Technical Sciences Department of Radiotechnic and Embedded Systems Chernihiv Polytechnic National University ( Chernihiv Ukraine
2 shared publications Ruslan Zarovskyi
2 shared publications
Latest Publications
- Open Access
- 1 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 26, 113-118
Variable Structure Controller for Plastic Injection Moulding System
This paper discusses the approach to design of combined ANN and PID temperature controller for a plastic injection moulding system. The proposed method is based on integration of a conventional PID (PI) controller and a multilayer ANN. At the initial stage of operation, the ANN is trained in offline mode to approximately identify the dynamic parameters of the regulator optimised in terms of speed of response and overshoot. Under routine operation mode the ANN control structure is responsible for the fast transients whereas PID (PI) controller provides the high accuracy at the steady state condition. The paper focuses on the structure switching mechanism and the influence on the transient accuracy. In order to verify the proposed approach, the control system having various types of heaters has been modelled and simulated in Matlab/Simulink. The data obtained from the experiment verified the developed model and confirmed the results of simulations.
- 1 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 26, 113-118
Open AccessVariable Structure Controller for Plastic Injection Moulding System
This paper discusses the approach to design of combined ANN and PID temperature controller for a plastic injection moulding system. The proposed method is based on integration of a conventional PID (PI) controller and a multilayer ANN. At the initial stage of operation, the ANN is trained in offline mode to approximately identify the dynamic parameters of the regulator optimised in terms of speed of response and overshoot. Under routine operation mode the ANN control structure is responsible for the fast transients whereas PID (PI) controller provides the high accuracy at the steady state condition. The paper focuses on the structure switching mechanism and the influence on the transient accuracy. In order to verify the proposed approach, the control system having various types of heaters has been modelled and simulated in Matlab/Simulink. The data obtained from the experiment verified the developed model and confirmed the results of simulations.
- 1 April 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 271-276
Parameters identification of injection plastic moulding heaters
Predefined heater parameters are involved in self-tuned temperature control for plastic moulding. However the heater system transfer function depends on many external parameters, such as barrel filling level, type of plastic etc. This paper discusses a recursive least-square estimation of plastic moulding heater parameters identification. The real heaters have been estimated by recursive least-square method as 2nd or 3rd order transfer function having an error less than 7.5%. The optimal sampling time for the identification process of different heater cartridges has been obtained from Matlab simulation. The parameters of estimated model can be used in self-tuned temperature controllers for injection plastic moulding heater.
- 1 April 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 271-276
Parameters identification of injection plastic moulding heaters
Predefined heater parameters are involved in self-tuned temperature control for plastic moulding. However the heater system transfer function depends on many external parameters, such as barrel filling level, type of plastic etc. This paper discusses a recursive least-square estimation of plastic moulding heater parameters identification. The real heaters have been estimated by recursive least-square method as 2nd or 3rd order transfer function having an error less than 7.5%. The optimal sampling time for the identification process of different heater cartridges has been obtained from Matlab simulation. The parameters of estimated model can be used in self-tuned temperature controllers for injection plastic moulding heater.
- 1 February 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 362-364
Topology optimisation of wireless internet infrastructure
The paper discusses utilisation of the brute force methods for the task of towers distribution in wireless communication systems. The proposed algorithm allows to find an optimal allocation of a tower between the settlements. A simple wireless communication has been used as an example to investigate the functionality of the algorithm's software.
- 1 February 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 362-364
Topology optimisation of wireless internet infrastructure
The paper discusses utilisation of the brute force methods for the task of towers distribution in wireless communication systems. The proposed algorithm allows to find an optimal allocation of a tower between the settlements. A simple wireless communication has been used as an example to investigate the functionality of the algorithm's software.
- 1 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 29-32
Classification and comparative analysis of fast median filter structures
The classification of median filter hardware structure was proposed. Main differences, advantages and disadvantages of each class were described. Scalable and synthesizable Verilog-descriptions were designed for two fast hardware structures. HDL-descriptions were synthesized on Altera and Xilinx FPGA platforms, comparative analysis on the basis of resource utilization and clock rate was done.
- 1 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 29-32
Classification and comparative analysis of fast median filter structures
The classification of median filter hardware structure was proposed. Main differences, advantages and disadvantages of each class were described. Scalable and synthesizable Verilog-descriptions were designed for two fast hardware structures. HDL-descriptions were synthesized on Altera and Xilinx FPGA platforms, comparative analysis on the basis of resource utilization and clock rate was done.
- 1 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 365-369
Digital control of a zero-current switching quasi-resonant boost converter
The most important component of a closed-loop industrial control system is the communication unit located between a digital controller and the object being controlled. A pulse converter is usually used for this purpose in systems operating under pulse width modulation. However the dynamic characteristics of the converter bring a significant impact on the quality of the system regulation. This article discusses the design and implementation a closed-loop digital automatic control system for a zero-current switching quasi-resonant boost converter. It enables a high-speed transient process of the controlled object voltage having the advantages provided by pulse methods of electrical energy conversion. This paper also presents the simulation and experimental verification of the proposed approach.
- 1 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 365-369
Digital control of a zero-current switching quasi-resonant boost converter
The most important component of a closed-loop industrial control system is the communication unit located between a digital controller and the object being controlled. A pulse converter is usually used for this purpose in systems operating under pulse width modulation. However the dynamic characteristics of the converter bring a significant impact on the quality of the system regulation. This article discusses the design and implementation a closed-loop digital automatic control system for a zero-current switching quasi-resonant boost converter. It enables a high-speed transient process of the controlled object voltage having the advantages provided by pulse methods of electrical energy conversion. This paper also presents the simulation and experimental verification of the proposed approach.
- 1 February 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 275-278
A random PWM technique for Z-source inverter based on pseudorandom binary sequence bits
The paper analyses a random pulse width modulated technique applicable for Z-source inverter. The proposed technique comprises the random pulse position PWM with a randomised frequently triangular carrier having characteristics of both space vector and random lead-lag modulations. This random pulse PWM is produced through the logical comparison of the pseudorandom binary sequence bits with the PWM pulses corresponding to two fixed frequency triangular carriers. Matlab/Simulink was used for modelling and simulation of the proposed method. It has been found that the output harmonic spectra of a Z-source inverter operating under the PWM with randomised frequency are dispersed and continuously distributed that can significantly reduce acoustic noise generated by the inverter and the load.
- 1 February 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 275-278
A random PWM technique for Z-source inverter based on pseudorandom binary sequence bits
The paper analyses a random pulse width modulated technique applicable for Z-source inverter. The proposed technique comprises the random pulse position PWM with a randomised frequently triangular carrier having characteristics of both space vector and random lead-lag modulations. This random pulse PWM is produced through the logical comparison of the pseudorandom binary sequence bits with the PWM pulses corresponding to two fixed frequency triangular carriers. Matlab/Simulink was used for modelling and simulation of the proposed method. It has been found that the output harmonic spectra of a Z-source inverter operating under the PWM with randomised frequency are dispersed and continuously distributed that can significantly reduce acoustic noise generated by the inverter and the load.
- 1 February 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 89-92
Evaluating the effectiveness of hierarchical management systems
This paper demonstrates a possibilities of using brute force methods for evaluating the effectiveness of hierarchical management systems. Proposed model of hierarchy provides finding the optimal distribution of load between the executive elements at a predetermined structure. A simple hierarchical structure has been used as an example to investigate the functionality of the model and its software implementation.
- 1 February 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 89-92
Evaluating the effectiveness of hierarchical management systems
This paper demonstrates a possibilities of using brute force methods for evaluating the effectiveness of hierarchical management systems. Proposed model of hierarchy provides finding the optimal distribution of load between the executive elements at a predetermined structure. A simple hierarchical structure has been used as an example to investigate the functionality of the model and its software implementation.
- 1 January 2015
- Published by European Alliance for Innovation n.o.
- p. 133-138
Artificial Neural Network-based Maximum Power Point Tracker for the Photovoltaic Application
This paper proposes a new artificial neural network-based maximum power point tracker for photovoltaic application. This tracker significantly improves efficiency of the photovoltaic system with series-connection of photovoltaic modules in non-uniform irradiance on photovoltaic array surfaces. The artificial neural network uses irradiance and temperature sensors to generate the maximum power point reference voltage and employ a classical perturb and observe searching algorithm. The structure of the artificial neural network was obtained by numerical modelling using Matlab/Simulink. The artificial neural network was trained using Bayesian regularisation back-propagation algorithms and demonstrated a good prediction of the maximum power point. Efficiency of proposed ANN-based MPP tracker has been estimated for linear shadow expanding and constant partial shading of any one PV module.
- 1 January 2015
- Published by European Alliance for Innovation n.o.
- p. 133-138
Artificial Neural Network-based Maximum Power Point Tracker for the Photovoltaic Application
This paper proposes a new artificial neural network-based maximum power point tracker for photovoltaic application. This tracker significantly improves efficiency of the photovoltaic system with series-connection of photovoltaic modules in non-uniform irradiance on photovoltaic array surfaces. The artificial neural network uses irradiance and temperature sensors to generate the maximum power point reference voltage and employ a classical perturb and observe searching algorithm. The structure of the artificial neural network was obtained by numerical modelling using Matlab/Simulink. The artificial neural network was trained using Bayesian regularisation back-propagation algorithms and demonstrated a good prediction of the maximum power point. Efficiency of proposed ANN-based MPP tracker has been estimated for linear shadow expanding and constant partial shading of any one PV module.
- 1 January 2015
- Published by Inderscience Publishers in International Journal of Systems, Control and Communications
- Vol. 6 (3) , 222
Error analysis in a high accuracy sampled-data velocity stabilising system using Volterra series
The paper presents a new method of analysis of error in a sampled-data velocity stabilising system operating under wide range pulse width modulation. The analysis is based on multi-channel model of the system obtained as a result of approximation of pulse-modulated signal from the output of a PWM converter. Approximation of piecewise-linear modulation characteristics of each channel was obtained as a series expansion of Hermite polynomials where the expansion comprises two polynomials of the first and third orders. Transfer functions of each channel and a closed-loop system were obtained using a multidimensional Z-transform based on Volterra series. The analytical expression of error under impact of a step input was derived using the transfer function of the closed-loop system. A DC electric drive was used as an example of high accuracy sample-data stabilising system in order to simulate and verify the proposed method.
- 1 January 2015
- Published by Inderscience Publishers in International Journal of Systems, Control and Communications
- Vol. 6 (3) , 222
Error analysis in a high accuracy sampled-data velocity stabilising system using Volterra series
The paper presents a new method of analysis of error in a sampled-data velocity stabilising system operating under wide range pulse width modulation. The analysis is based on multi-channel model of the system obtained as a result of approximation of pulse-modulated signal from the output of a PWM converter. Approximation of piecewise-linear modulation characteristics of each channel was obtained as a series expansion of Hermite polynomials where the expansion comprises two polynomials of the first and third orders. Transfer functions of each channel and a closed-loop system were obtained using a multidimensional Z-transform based on Volterra series. The analytical expression of error under impact of a step input was derived using the transfer function of the closed-loop system. A DC electric drive was used as an example of high accuracy sample-data stabilising system in order to simulate and verify the proposed method.