Ang Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ang Li has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Donghui Zhang
Department of Chemistry and Macromolecular Studies Group, Louisiana State University, Baton Rouge, LA 70803, USA
5 shared publications - Changwoo Do
Neutron Scattering Division, Oak Ridge National Laboratory, Oak Ridge, TN, 37831, USA
2 shared publications - Guoqiang Li
Department of Mechanical Engineering Southern University and A & M College Baton Rouge Louisiana USA
2 shared publications Xin Li
Department of Chemistry and Macromolecular Studies Group, Louisiana State University, Baton Rouge, USA
2 shared publicationsAdithya Challapalli
Department of Mechanical & Industrial Engineering, Louisiana State University, Baton Rouge, Louisiana, 70803, USA
1 shared publication- Biqing Huang
Department of Automation, Tsinghua University, Beijing 100084, China
1 shared publication
Latest Publications
- 24 August 2021
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (4) , 51541
Effects of sample thickness on the combustion and smoke characteristics of chlorinated polyvinyl chloride
Chlorinated polyvinyl chloride (CPVC), as an important engineering plastic, its combustion and smoke characteristics were studied based on different thicknesses using cone calorimeter. The main combustion parameters including thermal thickness, ignition time, mass loss rate (MLR), heat release rate (HRR), fire performance index (FPI), fire growth index (FGI), smoke production rate (SPR), and CO/CO2 were discussed. Results show that the thermal thickness increases with the decrease of external heat flux. The first or second peaks of MLR and HRR curves based on three thicknesses have a good linear relationship with the external heat flux. The heat of gasification is estimated as 8.09 kJ/g according to slope by the first and second MLR curves as a function of the external heat flux. The calculation results of effective heat of combustion show that thickness can affect the heat release during combustion. In addition, the positive correlation between the first peak SPR and the first peak HRR not only indicates that CPVC is a combustible material, but also shows there is a correlation between the heat release and smoke emission of CPVC during combustion.
- 24 August 2021
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (4) , 51541
Effects of sample thickness on the combustion and smoke characteristics of chlorinated polyvinyl chloride
Chlorinated polyvinyl chloride (CPVC), as an important engineering plastic, its combustion and smoke characteristics were studied based on different thicknesses using cone calorimeter. The main combustion parameters including thermal thickness, ignition time, mass loss rate (MLR), heat release rate (HRR), fire performance index (FPI), fire growth index (FGI), smoke production rate (SPR), and CO/CO2 were discussed. Results show that the thermal thickness increases with the decrease of external heat flux. The first or second peaks of MLR and HRR curves based on three thicknesses have a good linear relationship with the external heat flux. The heat of gasification is estimated as 8.09 kJ/g according to slope by the first and second MLR curves as a function of the external heat flux. The calculation results of effective heat of combustion show that thickness can affect the heat release during combustion. In addition, the positive correlation between the first peak SPR and the first peak HRR not only indicates that CPVC is a combustible material, but also shows there is a correlation between the heat release and smoke emission of CPVC during combustion.
- Open Access
- 20 May 2019
- Published by Springer Nature in Scientific Reports
- Vol. 9 (1) , 1-13
4D Printing of Recyclable Lightweight Architectures Using High Recovery Stress Shape Memory Polymer
High-performance lightweight architectures, such as metallic microlattices with excellent mechanical properties have been 3D printed, but they do not possess shape memory effect (SME), limiting their usages for advanced engineering structures, such as serving as a core in multifunctional lightweight sandwich structures. 3D printable self-healing shape memory polymer (SMP) microlattices could be a solution. However, existing 3D printable thermoset SMPs are limited to either low strength, poor stress memory, or non-recyclability. To address this issue, a new thermoset polymer, integrated with high strength, high recovery stress, perfect shape recovery, good recyclability, and 3D printability using direct light printing, has been developed in this study. Lightweight microlattices with various unit cells and length scales were printed and tested. The results show that the cubic microlattice has mechanical strength comparable to or even greater than that of metallic microlattices, good SME, decent recovery stress, and recyclability, making it the first multifunctional lightweight architecture (MLA) for potential multifunctional lightweight load carrying structural applications.
- 20 May 2019
- Published by Springer Nature in Scientific Reports
- Vol. 9 (1) , 1-13
Open Access4D Printing of Recyclable Lightweight Architectures Using High Recovery Stress Shape Memory Polymer
High-performance lightweight architectures, such as metallic microlattices with excellent mechanical properties have been 3D printed, but they do not possess shape memory effect (SME), limiting their usages for advanced engineering structures, such as serving as a core in multifunctional lightweight sandwich structures. 3D printable self-healing shape memory polymer (SMP) microlattices could be a solution. However, existing 3D printable thermoset SMPs are limited to either low strength, poor stress memory, or non-recyclability. To address this issue, a new thermoset polymer, integrated with high strength, high recovery stress, perfect shape recovery, good recyclability, and 3D printability using direct light printing, has been developed in this study. Lightweight microlattices with various unit cells and length scales were printed and tested. The results show that the cubic microlattice has mechanical strength comparable to or even greater than that of metallic microlattices, good SME, decent recovery stress, and recyclability, making it the first multifunctional lightweight architecture (MLA) for potential multifunctional lightweight load carrying structural applications.
- 16 May 2018
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 6 (24) , 11479-11487
Recyclable thermoset shape memory polymers with high stress and energy output via facile UV-curing
Engineering applications of current thermoset shape memory polymers are limited by three critical issues: demanding fabrication conditions (from 70 to 300 °C temperatures for hours or days), lack of reprocessability or recyclability, and low recovery stress and energy output. To address these problems simultaneously, a new UV curable and vitrimer-based epoxy thermoset shape memory polymer (VSMP) has been synthesized. A 1.1 mm thick VSMP film can be readily cured at room temperature under UV-irradiation (61 mW cm−2) in just 80 s. It possesses 36.7 MPa tensile strength, 230 MPa compressive strength, and 3120 MPa modulus at room temperature. It still has a compressive strength of 187 MPa at 120 °C. The covalent adaptable network (CAN) imparts the VSMP with recyclability, as reflected by two effective recycling cycles (>60% recycling efficiency). In addition, the VSMP exhibits good shape memory properties for multiple shape recovery cycles. With 20% compression programming strain, up to 13.4 MPa stable recovery stress and 1.05 MJ m−3 energy output in the rubbery state are achieved. With good mechanical strength, thermal stability, recyclability, and excellent shape memory properties combined with in situ UV-curing capabilities, the new VSMP is a promising multifunctional thermoset for engineering applications.
- 16 May 2018
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 6 (24) , 11479-11487
Recyclable thermoset shape memory polymers with high stress and energy output via facile UV-curing
Engineering applications of current thermoset shape memory polymers are limited by three critical issues: demanding fabrication conditions (from 70 to 300 °C temperatures for hours or days), lack of reprocessability or recyclability, and low recovery stress and energy output. To address these problems simultaneously, a new UV curable and vitrimer-based epoxy thermoset shape memory polymer (VSMP) has been synthesized. A 1.1 mm thick VSMP film can be readily cured at room temperature under UV-irradiation (61 mW cm−2) in just 80 s. It possesses 36.7 MPa tensile strength, 230 MPa compressive strength, and 3120 MPa modulus at room temperature. It still has a compressive strength of 187 MPa at 120 °C. The covalent adaptable network (CAN) imparts the VSMP with recyclability, as reflected by two effective recycling cycles (>60% recycling efficiency). In addition, the VSMP exhibits good shape memory properties for multiple shape recovery cycles. With 20% compression programming strain, up to 13.4 MPa stable recovery stress and 1.05 MJ m−3 energy output in the rubbery state are achieved. With good mechanical strength, thermal stability, recyclability, and excellent shape memory properties combined with in situ UV-curing capabilities, the new VSMP is a promising multifunctional thermoset for engineering applications.
- 25 October 2017
- Published by Wiley in Biopolymers
- Vol. 109 (1)
Polypeptoid polymers: Synthesis, characterization, and properties
Polypeptoids, a class of peptidomimetic polymers, have emerged at the forefront of macromolecular and supramolecular science and engineering as the technological relevance of these polymers continues to be demonstrated. The chemical and structural diversity of polypeptoids have enabled access to and adjustment of a variety of physicochemical and biological properties (eg, solubility, charge characteristics, chain conformation, HLB, thermal processability, degradability, cytotoxicity and immunogenicity). These attributes have made this synthetic polymer platform a potential candidate for various biomedical and biotechnological applications. This review will provide an overview of recent development in synthetic methods to access polypeptoid polymers with well‐defined structures and highlight some of the fundamental physicochemical and biological properties of polypeptoids that are pertinent to the future development of functional materials based on polypeptoids.
- 25 October 2017
- Published by Wiley in Biopolymers
- Vol. 109 (1)
Polypeptoid polymers: Synthesis, characterization, and properties
Polypeptoids, a class of peptidomimetic polymers, have emerged at the forefront of macromolecular and supramolecular science and engineering as the technological relevance of these polymers continues to be demonstrated. The chemical and structural diversity of polypeptoids have enabled access to and adjustment of a variety of physicochemical and biological properties (eg, solubility, charge characteristics, chain conformation, HLB, thermal processability, degradability, cytotoxicity and immunogenicity). These attributes have made this synthetic polymer platform a potential candidate for various biomedical and biotechnological applications. This review will provide an overview of recent development in synthetic methods to access polypeptoid polymers with well‐defined structures and highlight some of the fundamental physicochemical and biological properties of polypeptoids that are pertinent to the future development of functional materials based on polypeptoids.
- 12 April 2017
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 19 (22) , 14388-14400
Aggregation of cyclic polypeptoids bearing zwitterionic end-groups with attractive dipole–dipole and solvophobic interactions: a study by small-angle neutron scattering and molecular dynamics simulation
The aggregation behavior of cyclic polypeptoids has been studied using experiments and simulations.
- 12 April 2017
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 19 (22) , 14388-14400
Aggregation of cyclic polypeptoids bearing zwitterionic end-groups with attractive dipole–dipole and solvophobic interactions: a study by small-angle neutron scattering and molecular dynamics simulation
The aggregation behavior of cyclic polypeptoids has been studied using experiments and simulations.
- 26 February 2016
- Published by American Chemical Society (ACS) in Biomacromolecules
- Vol. 17 (3) , 852-861
Synthesis and Characterization of Cleavable Core-Cross-Linked Micelles Based on Amphiphilic Block Copolypeptoids as Smart Drug Carriers
Amphiphilic block copolypeptoids consisting of a hydrophilic poly(N-ethyl glycine) segment and a hydrophobic poly[(N-propargyl glycine)-r-(N-decyl glycine)] random copolymer segment [PNEG-b-P(NPgG-r-NDG), EPgD] have been synthesized by sequential primary amine-initiated ring-opening polymerization (ROP) of the corresponding N-alkyl N-carboxyanhydride monomers. The block copolypeptoids form micelles in water and the micellar core can be cross-linked with a disulfide-containing diazide cross-linker by copper-mediated alkyne–azide cycloaddition (CuAAC) in aqueous solution. Transmission electron microscopy (TEM) and dynamic light scattering (DLS) analysis revealed the formation of spherical micelles with uniform size for both the core-cross-linked micelles (CCLMs) and non-cross-linked micelles (NCLMs) precursors for selective block copolypeptoid polymers. The CCLMs exhibited increased dimensional stability relative to the NCLMs in DMF, a nonselective solvent for the core and corona segments. Micellar dissociation of CCLMs can be induced upon addition of a reducing agent (e.g., dithiothreitol) in dilute aqueous solutions, as verified by a combination of fluorescence spectroscopy, size exclusion chromatography (SEC), and 1H NMR spectroscopic measurement. Doxorubicin (DOX), an anticancer drug, can be loaded into the hydrophobic core of CCLMs with a maximal 23% drug loading capacity (DLC) and 37% drug loading efficiency (DLE). In vitro DOX release from the CCLMs can be triggered by DTT (10 mM), in contrast to significantly reduced DOX release in the absence of DTT, attesting to the reductively responsive characteristic of the CCLMs. While the CCLMs exhibited minimal cytotoxicity toward HepG2 cancer cells, DOX-loaded CCLMs inhibited the proliferation of the HepG2 cancer cells in a concentration and time dependent manner, suggesting the controlled release of DOX from the DOX-loaded CCLMS in the cellular environment.
- 26 February 2016
- Published by American Chemical Society (ACS) in Biomacromolecules
- Vol. 17 (3) , 852-861
Synthesis and Characterization of Cleavable Core-Cross-Linked Micelles Based on Amphiphilic Block Copolypeptoids as Smart Drug Carriers
Amphiphilic block copolypeptoids consisting of a hydrophilic poly(N-ethyl glycine) segment and a hydrophobic poly[(N-propargyl glycine)-r-(N-decyl glycine)] random copolymer segment [PNEG-b-P(NPgG-r-NDG), EPgD] have been synthesized by sequential primary amine-initiated ring-opening polymerization (ROP) of the corresponding N-alkyl N-carboxyanhydride monomers. The block copolypeptoids form micelles in water and the micellar core can be cross-linked with a disulfide-containing diazide cross-linker by copper-mediated alkyne–azide cycloaddition (CuAAC) in aqueous solution. Transmission electron microscopy (TEM) and dynamic light scattering (DLS) analysis revealed the formation of spherical micelles with uniform size for both the core-cross-linked micelles (CCLMs) and non-cross-linked micelles (NCLMs) precursors for selective block copolypeptoid polymers. The CCLMs exhibited increased dimensional stability relative to the NCLMs in DMF, a nonselective solvent for the core and corona segments. Micellar dissociation of CCLMs can be induced upon addition of a reducing agent (e.g., dithiothreitol) in dilute aqueous solutions, as verified by a combination of fluorescence spectroscopy, size exclusion chromatography (SEC), and 1H NMR spectroscopic measurement. Doxorubicin (DOX), an anticancer drug, can be loaded into the hydrophobic core of CCLMs with a maximal 23% drug loading capacity (DLC) and 37% drug loading efficiency (DLE). In vitro DOX release from the CCLMs can be triggered by DTT (10 mM), in contrast to significantly reduced DOX release in the absence of DTT, attesting to the reductively responsive characteristic of the CCLMs. While the CCLMs exhibited minimal cytotoxicity toward HepG2 cancer cells, DOX-loaded CCLMs inhibited the proliferation of the HepG2 cancer cells in a concentration and time dependent manner, suggesting the controlled release of DOX from the DOX-loaded CCLMS in the cellular environment.
- 5 February 2016
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 49 (4) , 1163-1171
Amidine-Mediated Zwitterionic Ring-Opening Polymerization of N-Alkyl N-Carboxyanhydride: Mechanism, Kinetics, and Architecture Elucidation
- 5 February 2016
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 49 (4) , 1163-1171
Amidine-Mediated Zwitterionic Ring-Opening Polymerization of N-Alkyl N-Carboxyanhydride: Mechanism, Kinetics, and Architecture Elucidation
- 7 October 2013
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 46 (20) , 8213-8223
Crystallization and Melting Behaviors of Cyclic and Linear Polypeptoids with Alkyl Side Chains
- 7 October 2013
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 46 (20) , 8213-8223
Crystallization and Melting Behaviors of Cyclic and Linear Polypeptoids with Alkyl Side Chains