Yu Du
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yu Du has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Huaxia Deng
University of Science and Technology of China
5 shared publications Jin Zhang
4 shared publicationsXiang Zhong
4 shared publications- Zhemin Wang
School of Instrument Science and Opto-electronics Engineering, Hefei University of Technology , Hefei, Anhui 230009, People's Republic of China
4 shared publications Mengchao Ma
3 shared publications- Ping Li
Shanghai Jiao Tong University
3 shared publications
Latest Publications
- Open Access
- 22 November 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1)
Mechanical self-adaptive porous valve relying on surface tension for energy harvesting from low-flux bubbles
Harvesting energy from subsea bubbles, such as those produced by photosynthesis of benthic plants or submarine methane seepage, is a promising solution for powering subsea environment perception devices, but the low gas flux brings significant challenges. Herein, we propose a passive mechanical self-adaptive porous valve with self-adaptive mechanical properties and high gas permeability. It improves energy harvesting performance from low-flux bubbles by controlling bubble accumulation and high-speed release. Unlike traditional active mechanical metamaterials, this passive design utilizes gas-liquid interface deformation (rather than metamaterial actuation) to generate self-adaptive Laplace pressure counteracting bubble buoyancy, and thus requires no external energy. The porous valve has a stable opening threshold inversely proportional to its structural pore diameter. Compared with a bubble energy harvesting device with no valve, the instantaneous gas-intake rate of the device equipped with the porous valve is increased by one to four orders of magnitude, and the maximum output power and electrical energy production are enhanced by factors of 36.6 and 16.4, respectively. The energy of underwater biological metabolic gas with a low flux (28 μL $$\cdot \, {\min }^{-1}$$ ) is effectively harvested and supplied to an underwater sensor. This work is expected to provide in situ energy for subsea self-powered sensing and autonomous exploration.- 22 November 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1)
Open AccessMechanical self-adaptive porous valve relying on surface tension for energy harvesting from low-flux bubbles
Harvesting energy from subsea bubbles, such as those produced by photosynthesis of benthic plants or submarine methane seepage, is a promising solution for powering subsea environment perception devices, but the low gas flux brings significant challenges. Herein, we propose a passive mechanical self-adaptive porous valve with self-adaptive mechanical properties and high gas permeability. It improves energy harvesting performance from low-flux bubbles by controlling bubble accumulation and high-speed release. Unlike traditional active mechanical metamaterials, this passive design utilizes gas-liquid interface deformation (rather than metamaterial actuation) to generate self-adaptive Laplace pressure counteracting bubble buoyancy, and thus requires no external energy. The porous valve has a stable opening threshold inversely proportional to its structural pore diameter. Compared with a bubble energy harvesting device with no valve, the instantaneous gas-intake rate of the device equipped with the porous valve is increased by one to four orders of magnitude, and the maximum output power and electrical energy production are enhanced by factors of 36.6 and 16.4, respectively. The energy of underwater biological metabolic gas with a low flux (28 μL $$\cdot \, {\min }^{-1}$$ ) is effectively harvested and supplied to an underwater sensor. This work is expected to provide in situ energy for subsea self-powered sensing and autonomous exploration. Super‐Aerophilic Biomimetic Cactus for Underwater Dispersed Microbubble Capture, Self‐Transport, Coalescence, and Energy Harvesting
Human ocean activities are inseparable from the supply of energy. The energy contained in the gas‐phase components dispersed in seawater is a potential universal energy source for eupelagic or deep‐sea equipment. However, the low energy density of bubbles dispersed in water introduces severe challenges to the potential energy harvesting of gas‐phase components. Here, a super‐aerophilic biomimetic cactus is developed for underwater dispersive microbubble capture and energy harvesting. The bubbles captured by the super‐aerophilic biomimetic cactus spines, driven by the surface tension and liquid pressure, undergo automatic transport, coalescence, accumulation, and concentrated release. The formerly unavailable low‐density dispersive surface free energy of the bubbles is converted into high‐density concentrated gas buoyancy potential energy, thereby providing an energy source for underwater in situ electricity generation. Experiments show a continuous process of microbubble capture by the biomimetic cactus and demonstrate a 22.76‐times increase in output power and a 3.56‐times enhancement in electrical energy production compared with a conventional bubble energy harvesting device. The output energy density is 3.64 times that of the existing bubble energy generator. This work provides a novel approach for dispersive gas‐phase potential energy harvesting in seawater, opening up promising prospects for wide‐area in situ energy supply in underwater environments.
Super‐Aerophilic Biomimetic Cactus for Underwater Dispersed Microbubble Capture, Self‐Transport, Coalescence, and Energy Harvesting
Human ocean activities are inseparable from the supply of energy. The energy contained in the gas‐phase components dispersed in seawater is a potential universal energy source for eupelagic or deep‐sea equipment. However, the low energy density of bubbles dispersed in water introduces severe challenges to the potential energy harvesting of gas‐phase components. Here, a super‐aerophilic biomimetic cactus is developed for underwater dispersive microbubble capture and energy harvesting. The bubbles captured by the super‐aerophilic biomimetic cactus spines, driven by the surface tension and liquid pressure, undergo automatic transport, coalescence, accumulation, and concentrated release. The formerly unavailable low‐density dispersive surface free energy of the bubbles is converted into high‐density concentrated gas buoyancy potential energy, thereby providing an energy source for underwater in situ electricity generation. Experiments show a continuous process of microbubble capture by the biomimetic cactus and demonstrate a 22.76‐times increase in output power and a 3.56‐times enhancement in electrical energy production compared with a conventional bubble energy harvesting device. The output energy density is 3.64 times that of the existing bubble energy generator. This work provides a novel approach for dispersive gas‐phase potential energy harvesting in seawater, opening up promising prospects for wide‐area in situ energy supply in underwater environments.
- 1 December 2022
- Published by Elsevier in Sustainable Energy Technologies and Assessments
- Vol. 55
Efficient and high-power subsea bubble energy harvesting by controlling flow pattern
- 1 December 2022
- Published by Elsevier in Sustainable Energy Technologies and Assessments
- Vol. 55
Efficient and high-power subsea bubble energy harvesting by controlling flow pattern
- 1 December 2021
- Published by Elsevier in Applied Energy
- Vol. 303
A flute-inspired broadband piezoelectric vibration energy harvesting device with mechanical intelligent design
- 1 December 2021
- Published by Elsevier in Applied Energy
- Vol. 303
A flute-inspired broadband piezoelectric vibration energy harvesting device with mechanical intelligent design
- 7 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 389-393
Development and Thermal Characterization of a Low Resistance SiC Module
A low conduction resistance 1200 V/ 4 m$\Omega$ SiC power module is fabricated and characterized for its thermal performance. The design and fabrication of the power module is presented. The parasitic resistance distribution from the module prototype is measured and shows that it is critical to minimize the source bond wire and contact resistance for such low on-state resistance module. The steady-state thermal tests are performed, and the temperature distribution of the fabricated module is measured and validated. A FEA model of the SiC module is built and validated by the steady-state thermal tests. Then the transient thermal performance or surge current capacity is studied. It shows that at least 4 bond wires are required for each SiC die such that the module package will not limit the surge current capacity of SiC chips.
- 7 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 389-393
Development and Thermal Characterization of a Low Resistance SiC Module
A low conduction resistance 1200 V/ 4 m$\Omega$ SiC power module is fabricated and characterized for its thermal performance. The design and fabrication of the power module is presented. The parasitic resistance distribution from the module prototype is measured and shows that it is critical to minimize the source bond wire and contact resistance for such low on-state resistance module. The steady-state thermal tests are performed, and the temperature distribution of the fabricated module is measured and validated. A FEA model of the SiC module is built and validated by the steady-state thermal tests. Then the transient thermal performance or surge current capacity is studied. It shows that at least 4 bond wires are required for each SiC die such that the module package will not limit the surge current capacity of SiC chips.
- 1 December 2020
- Published by Elsevier in Nano Energy
- Vol. 78
Energy transfer and redistribution: An approach for unifying vibrational energy harvesting and vibration attenuation
- 1 December 2020
- Published by Elsevier in Nano Energy
- Vol. 78
Energy transfer and redistribution: An approach for unifying vibrational energy harvesting and vibration attenuation
- 1 November 2019
- Published by Elsevier in Nano Energy
- Vol. 65
Bistable broadband hybrid generator for ultralow-frequency rectilinear motion
- 1 November 2019
- Published by Elsevier in Nano Energy
- Vol. 65
Bistable broadband hybrid generator for ultralow-frequency rectilinear motion
- Open Access
- 26 February 2019
- Published by Springer Nature in Communications Physics
- Vol. 2 (1) , 21
Poly-stable energy harvesting based on synergetic multistable vibration
Distributed energy sources, for example the ambient broadband vibrations, are of great importance for the development of the Internet of Things. However, for multistable vibrational energy harvesters, increasing the number of stable equilibrium states to broaden working frequency bands is very difficult. Here we present a poly-stable vibrational energy harvesting approach capable of achieving an exponentially growing maximum number of stable equilibrium states. Unlike the traditional multistable harvesters relying on an external static magnetic field, the nonlinear dynamical behaviours achieved by the proposed approach are synergetic poly-stable motions without the need of external magnets. Comparison experiments in contrast with a linear harvester demonstrate the working bandwidth widened by a factor of 41.0, the power density increased to 760% and the electricity generation raised to 178%. This demonstration of new multistable energy harvester expands the approach to achieving multistable motion and provides a new design philosophy for nonlinear vibrational energy harvesters.
- 26 February 2019
- Published by Springer Nature in Communications Physics
- Vol. 2 (1) , 21
Open AccessPoly-stable energy harvesting based on synergetic multistable vibration
Distributed energy sources, for example the ambient broadband vibrations, are of great importance for the development of the Internet of Things. However, for multistable vibrational energy harvesters, increasing the number of stable equilibrium states to broaden working frequency bands is very difficult. Here we present a poly-stable vibrational energy harvesting approach capable of achieving an exponentially growing maximum number of stable equilibrium states. Unlike the traditional multistable harvesters relying on an external static magnetic field, the nonlinear dynamical behaviours achieved by the proposed approach are synergetic poly-stable motions without the need of external magnets. Comparison experiments in contrast with a linear harvester demonstrate the working bandwidth widened by a factor of 41.0, the power density increased to 760% and the electricity generation raised to 178%. This demonstration of new multistable energy harvester expands the approach to achieving multistable motion and provides a new design philosophy for nonlinear vibrational energy harvesters.
- 6 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 24 (1) , 282-292
A Compact and Flexible Nonbeam-Type Vibrational Energy Harvesting Device With Bistable Characteristics
Conventional beam-type vibrational energy harvesting devices suffer from poor low-frequency performance, stress concentration, and limited compatibility with other device structures. This paper proposes a vibrational energy harvester based on a novel bellows structure together with permanent magnets that exploits nonlinear bistability to enhance its performance at low frequencies. The device uses a flexible bellows tube that is compact and can also be used as an elastic unit instead of springs in other vibration-based devices. First, the structural configuration of a prototype device is described, after which the equations of motion are established to allow a bistability analysis of the device. Simulations and experiments are carried out to investigate the effects of various parameters on the bistability, including the distance between magnets, the excitation amplitude, and the excitation frequency. The performance of the proposed device is investigated experimentally for excitation frequencies from 2 to 15 Hz and is compared with the performance of a device without external magnets. This compact nonbeam-type bistable energy harvesting device represents a new design of bistable vibration energy harvester, which has the potential to provide higher output power at lower working frequencies.
- 6 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 24 (1) , 282-292
A Compact and Flexible Nonbeam-Type Vibrational Energy Harvesting Device With Bistable Characteristics
Conventional beam-type vibrational energy harvesting devices suffer from poor low-frequency performance, stress concentration, and limited compatibility with other device structures. This paper proposes a vibrational energy harvester based on a novel bellows structure together with permanent magnets that exploits nonlinear bistability to enhance its performance at low frequencies. The device uses a flexible bellows tube that is compact and can also be used as an elastic unit instead of springs in other vibration-based devices. First, the structural configuration of a prototype device is described, after which the equations of motion are established to allow a bistability analysis of the device. Simulations and experiments are carried out to investigate the effects of various parameters on the bistability, including the distance between magnets, the excitation amplitude, and the excitation frequency. The performance of the proposed device is investigated experimentally for excitation frequencies from 2 to 15 Hz and is compared with the performance of a device without external magnets. This compact nonbeam-type bistable energy harvesting device represents a new design of bistable vibration energy harvester, which has the potential to provide higher output power at lower working frequencies.
- 21 May 2018
- Published by AIP Publishing in Applied Physics Letters
- Vol. 112 (21) , 213901
A multimodal and multidirectional vibrational energy harvester using a double-branched beam
Vibrational energy harvesters, which are generally based on a single cantilever beam, are mainly effective for excitations perpendicular to the beam. However, typical ambient vibrations are of multifrequency and are multidirectional. To achieve full harvesting of multifrequency vibrational energy in multiple directions, this letter proposes a multidirectional vibrational energy harvester utilizing multimodal vibrations of a double-branched beam that has four natural frequencies below 22 Hz. Comparison experiments in different directions demonstrate an improvement of energy harvesting when this double-branched beam is used. Under horizontal excitation, the maximum open-circuit voltage is increased to 1845%. Under vertical excitation, the average power density is increased over 3800 times. The experimental results indicate that this structural design significantly improves the energy collection efficiency in both horizontal and vertical directions, even with a lighter structural weight.
- 21 May 2018
- Published by AIP Publishing in Applied Physics Letters
- Vol. 112 (21) , 213901
A multimodal and multidirectional vibrational energy harvester using a double-branched beam
Vibrational energy harvesters, which are generally based on a single cantilever beam, are mainly effective for excitations perpendicular to the beam. However, typical ambient vibrations are of multifrequency and are multidirectional. To achieve full harvesting of multifrequency vibrational energy in multiple directions, this letter proposes a multidirectional vibrational energy harvester utilizing multimodal vibrations of a double-branched beam that has four natural frequencies below 22 Hz. Comparison experiments in different directions demonstrate an improvement of energy harvesting when this double-branched beam is used. Under horizontal excitation, the maximum open-circuit voltage is increased to 1845%. Under vertical excitation, the average power density is increased over 3800 times. The experimental results indicate that this structural design significantly improves the energy collection efficiency in both horizontal and vertical directions, even with a lighter structural weight.