Giorgio Bartolozzi
Research Subjects
Giorgio Bartolozzi has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Marco Pierini
University of Florence, IT
4 shared publications Niccolò Baldanzini
3 shared publicationsAndrea Camia
FCA Italy S.p.A.
2 shared publicationsGiovanni Zonfrillo
2 shared publicationsMarco Danti
Centro Ricerche Fiat Scpa
2 shared publicationsDavide Vige
FCA Italy S.p.A.
1 shared publication
Latest Publications
- 15 June 2016
- Published by SAE International in SAE International Journal of Passenger Cars - Mechanical Systems
- Vol. 09 (3) , 1091-1099
Enhancement of Full-Vehicle Road Noise Simulation Including Detailed Road Surface and Innovative Tire Modeling
The time to market in the automotive industry is constantly decreasing pushing the carmaker companies to increase the efforts in numerical simulations and to decrease the number of prototypes. In the NVH field, this time constraint reflects in moving the well-established finite element simulations towards the so called “full-vehicle simulations”. Specifically, the CAE techniques should be able to predict the complete behavior of the vehicles in mission conditions, so to reproduce some usual tests, such as the “coast down” test on different roads.The aim of this paper is to present a methodology to improve rolling noise simulations exploiting an integrated full-vehicle approach. An accurate modeling of all the subsystems is needed, with particular attention to the wheels and the suspension systems. Therefore, the paper firstly covers the modeling approach used to obtain the FE models of tires and suspension system. A particular focus is on the modeling of tires, since the typically used “modal models” are replaced by internally developed simplified FE models. Secondly, the rolling noise simulation approach is presented, by showing an easy-to-use tool developed to automatically set up the chosen full-vehicle simulation. The final aim is to have a quick technique to predict the overall behavior of the vehicle.The proposed methodology is assessed by means of a numerical-experimental comparison for a coast down test on cobblestone road. The comparison involves the acceleration at front and rear hubs to prove the effectiveness of the tire modeling. Moreover, the Sound Pressure Level (SPL) at the driver’s right ear is compared, which is the main target of the simulation.
- 15 June 2016
- Published by SAE International in SAE International Journal of Passenger Cars - Mechanical Systems
- Vol. 09 (3) , 1091-1099
Enhancement of Full-Vehicle Road Noise Simulation Including Detailed Road Surface and Innovative Tire Modeling
The time to market in the automotive industry is constantly decreasing pushing the carmaker companies to increase the efforts in numerical simulations and to decrease the number of prototypes. In the NVH field, this time constraint reflects in moving the well-established finite element simulations towards the so called “full-vehicle simulations”. Specifically, the CAE techniques should be able to predict the complete behavior of the vehicles in mission conditions, so to reproduce some usual tests, such as the “coast down” test on different roads.The aim of this paper is to present a methodology to improve rolling noise simulations exploiting an integrated full-vehicle approach. An accurate modeling of all the subsystems is needed, with particular attention to the wheels and the suspension systems. Therefore, the paper firstly covers the modeling approach used to obtain the FE models of tires and suspension system. A particular focus is on the modeling of tires, since the typically used “modal models” are replaced by internally developed simplified FE models. Secondly, the rolling noise simulation approach is presented, by showing an easy-to-use tool developed to automatically set up the chosen full-vehicle simulation. The final aim is to have a quick technique to predict the overall behavior of the vehicle.The proposed methodology is assessed by means of a numerical-experimental comparison for a coast down test on cobblestone road. The comparison involves the acceleration at front and rear hubs to prove the effectiveness of the tire modeling. Moreover, the Sound Pressure Level (SPL) at the driver’s right ear is compared, which is the main target of the simulation.
- 1 July 2015
- Published by Elsevier in Composite Structures
- Vol. 125, 343-353
Static and dynamic experimental validation of analytical homogenization models for corrugated core sandwich panels
- 1 July 2015
- Published by Elsevier in Composite Structures
- Vol. 125, 343-353
Static and dynamic experimental validation of analytical homogenization models for corrugated core sandwich panels
- 15 June 2015
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Simplified FE Modeling of Rolling Tires for the Simulation of Dynamic Forces at Hub Level
Within the automotive industry, a typical way to account for tires in a roadnoise mission simulation is to use the “modal model” supplied by tire manufacturers. Even though this kind of models is certified by the suppliers and is very simple to use, it has the drawback to be disconnected from the physical description of the tire. This reflects in limiting the carmaker company to be able only to request certain modal characteristics to the supplier.The aim of this paper is to present an accurate, yet easy to use, methodology to develop an FE model of a tire, to be used in a full-vehicle simulation. The determined model must be connected to the tire physical properties. These properties are not measured directly, but determined by tuning a properly created geometric FE model to the measured point inertances of the inflated tire. This allows creating the model only by using an optimization algorithm to tune such properties.One of the key features of the developed tire model concerns its reduced dimensions in terms of number of nodes and elements. This is crucial in view of the inclusion of such a model in a full-vehicle simulation and can be achieved by assuming a two-dimensional multi-layer representation of the tire. Despite the simplicity of such an assumption, the accuracy of the model is checked by comparing the simulated hub forces in rolling conditions with properly obtained measurements for different tires. Moreover, the sensibility of the model to the physical characteristics of the simulation, such as the rolling speed, is verified with respect to measurements.
- 15 June 2015
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Simplified FE Modeling of Rolling Tires for the Simulation of Dynamic Forces at Hub Level
Within the automotive industry, a typical way to account for tires in a roadnoise mission simulation is to use the “modal model” supplied by tire manufacturers. Even though this kind of models is certified by the suppliers and is very simple to use, it has the drawback to be disconnected from the physical description of the tire. This reflects in limiting the carmaker company to be able only to request certain modal characteristics to the supplier.The aim of this paper is to present an accurate, yet easy to use, methodology to develop an FE model of a tire, to be used in a full-vehicle simulation. The determined model must be connected to the tire physical properties. These properties are not measured directly, but determined by tuning a properly created geometric FE model to the measured point inertances of the inflated tire. This allows creating the model only by using an optimization algorithm to tune such properties.One of the key features of the developed tire model concerns its reduced dimensions in terms of number of nodes and elements. This is crucial in view of the inclusion of such a model in a full-vehicle simulation and can be achieved by assuming a two-dimensional multi-layer representation of the tire. Despite the simplicity of such an assumption, the accuracy of the model is checked by comparing the simulated hub forces in rolling conditions with properly obtained measurements for different tires. Moreover, the sensibility of the model to the physical characteristics of the simulation, such as the rolling speed, is verified with respect to measurements.
- 1 February 2014
- Published by Elsevier in Composite Structures
- Vol. 108, 736-746
Equivalent properties for corrugated cores of sandwich structures: A general analytical method
- 1 February 2014
- Published by Elsevier in Composite Structures
- Vol. 108, 736-746
Equivalent properties for corrugated cores of sandwich structures: A general analytical method
- 1 June 2013
- Published by Elsevier in Composite Structures
- Vol. 100, 173-185
An equivalent material formulation for sinusoidal corrugated cores of structural sandwich panels
- 1 June 2013
- Published by Elsevier in Composite Structures
- Vol. 100, 173-185
An equivalent material formulation for sinusoidal corrugated cores of structural sandwich panels