Optimization of Aging Temperature and Heat-Treatment Pathways in Additively Manufactured 17-4PH Stainless Steel
Open Access
Abstract
This study investigates the tensile behaviors of additively manufactured (AM) 17-4PH stainless steels heat-treated within various temperature ranges from 400 °C to 700 °C in order to identify the effective aging temperature. Despite an aging treatment of 400–460 °C increasing the retained austenite content, an enhancement of the tensile properties was achieved without a strength-ductility trade-off owing to precipitation hardening by the Cu particles. Due to the intricate evolution of the microstructure, aging treatments above 490 °C led to a loss in yield strength and ductility. A considerable rise in strength and a decrease in ductility were brought about by the increase in the fraction of precipitation-hardened martensitic matrix in aging treatments over 640 °C. The impact of heat-treatment pathways on aging effectiveness and tensile anisotropy was then examined. Direct aging at 482 °C for an hour had hardly any effect on wrought 17-4PH, but it increased the yield strength of AM counterparts from 436–457 to 588–604 MPa. A solid-solution treatment at 1038 °C for one hour resulted in a significant drop in the austenite fraction, which led to an increase in the yield (from 436–457 to 841–919 MPa) and tensile strengths (from 1106–1127 to 1254–1256 MPa) with a sacrifice in ductility. Improved strength and ductility were realized by a solid-solution followed by an aging treatment, achieving 1371–1399 MPa. The tensile behaviors of AM 17-4PH were isotropic both parallel and perpendicular to the building direction.Keywords
Funding Information
- National Research Foundation of Korea (2023R1A2C2007190, P0023676, 20223030030110, 524480-23)
- Korea Institute for Advancement of Technology (KIAT) (2023R1A2C2007190, P0023676, 20223030030110, 524480-23)
- Korea Institute of Energy Technology Evaluation and Planning (KETEP) (2023R1A2C2007190, P0023676, 20223030030110, 524480-23)
- Korea Institute of Energy Technology Evaluation and Planning (2023R1A2C2007190, P0023676, 20223030030110, 524480-23)
- Korea Atomic Energy Research Institute (2023R1A2C2007190, P0023676, 20223030030110, 524480-23)
This publication has 28 references indexed in Scilit:
- Additive Manufacturing of 17-4 PH Stainless Steel: Post-processing Heat Treatment to Achieve Uniform Reproducible MicrostructureJOM, 2015
- Evolution of solidification texture during additive manufacturingScientific Reports, 2015
- Thermo-kinetic modeling of Cu precipitation in α-FeActa Materialia, 2015
- Microstructure and Mechanical Behavior of 17-4 Precipitation Hardenable Steel Processed by Selective Laser MeltingJournal of Materials Engineering and Performance, 2014
- Neutron diffraction in situ monitoring of the dislocation density during martensitic transformation in a stainless steelScripta Materialia, 2013
- GSAS-II: the genesis of a modern open-source all purpose crystallography software packageJournal of Applied Crystallography, 2013
- Small-angle neutron scattering study on the cold rolled steel sheetsApplied Physics A, 2010
- Bainitic transformation behavior studied by simultaneous neutron diffraction and dilatometric measurementScripta Materialia, 2009
- In situ TOF neutron diffraction during phase transformation in an engineering steelNuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment, 2009
- The strength, fracture toughness, and low cycle fatigue behavior of 17-4 PH stainless steelMetallurgical Transactions, 1974