11.7 A Wide 0.1-to-10 Conversion-Ratio Symmetric Hybrid Buck-Boost Converter for USB PD Bidirectional Conversion
Authors:
- 19 February 2023
- conference paper
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 194-196
Abstract
In recent years, USB Power Delivery (USB PD) is playing an increasingly important role in the field of consumer electronics. The USB PD 3.1 extends the delivering voltage up to 48V, which requires a buck-boost converter with extreme conversion ratio $(\text{CR}= \mathrm{V}_{\text{OUT}}/\mathrm{V}_{\text{IN}})$ range from 0.1″,10, high-voltage (HW) stress switches, and fast transient response. Into the bargain, the USB Type-C interface with USB PD specification allows power delivery through a single port, which brings about the necessity for bi-directional power converter. To fulfill this task, one of the most common proposals is to implement two power converters for each direction, but this method will be costly to accomplish and will complicate the designs for controllers. Although the Three-level Buck-Boost converter (TLBB) in [1] can provide buck-boost conversion when $\mathrm{V}_{2} > 2\mathrm{V}_{1}$ (top left of Figure 11.7.1), node $\mathrm{V}_{\mathrm{x}}$ will be 2 times $\mathrm{V}_{1}$ , which leads to inductor charging in both $\varphi 1,\varphi 2$ , and fails to transfer power from $\mathrm{V}_{2}$ to $\mathrm{V}_{1}$ . To transfer power from $\mathrm{V}_{2}$ to $\mathrm{V}_{1}$ by using the double step-down converter (DSD) [2], $\mathrm{V}_{1}$ needs to be 4 times larger than $\mathrm{V}_{2}$ due to the limit of CR. In prior DC-DC converters, it is hard to achieve both wide-range CR and bi-directional power conversion. Thus, this paper proposes a symmetric hybrid buck-boost converter (SHBB), which contains two adjustable voltage switched-capacitor (AVSC) cells to satisfy the specifications mentioned above, as well as bi-directional power transmission. Conventional buck-boost (CBB) converter can reach full-range CR, but it encounters low CR=0.1 in the case of 48-to-5V conversion, leading to difficulty in driver and controller designs. The bottom-left of Figure 11.7.1 shows the CR range comparison chart with state-of-the-arts. The DSD converter [2] can provide extreme CR (24V to 1 V) with relatively wider duty cycles, but its maximum CR is limited to 0.25, which is not qualified for USB PD 3.1. Regarding boost conversion, the hybrid boost converter [3] and 3-switch boost converter [4] provide CR larger than 4, but they still fail to meet USB PD 3.1 requirements. The state-of-the-art buck-boost converters [1], [5] can operate in both buck and boost modes but the maximum CR is only 2. Furthermore, since the input and output voltage will vary from 5V to 48V, to tolerate high voltage stress over 96V $(2\times \mathrm{V}_{\text{in}})$ in [5], 48V $(\mathrm{V}_{\text{in}})$ in CBB, and [1], the usage of 60V HV process is unavoidable, which increases fabrication cost and decreases efficiency.
Keywords
This publication has 5 references indexed in Scilit:
- A 4A 12-to-1 Flying Capacitor Cross-Connected DC-DC Converter with Inserted D>0.5 Control Achieving >2x Transient Inductor Current Slew Rate and 0.73× Theoretical Minimum Output Undershoot of DSD2022
- 17.9 A High-Conversion-Ratio and 97.4% Peak-Efficiency 3-Switch Boost Converter with Duty-Dependent Charge Topology for 1.2A High Driving Current and 20% Reduction of Inductor DC Current in MiniLED Applications2021
- 11.7 A Voltage-Tolerant Three-Level Buck-Boost DC-DC Converter with Continuous Transfer Current and Flying Capacitor Soft Charger Achieving 96.8% Power Efficiency and 0.87µs/V DVS Rate2020
- 11.5 A 2-Phase Soft-Charging Hybrid Boost Converter with Doubled-Switching Pulse Width and Shared Bootstrap Capacitor Achieving 93.5% Efficiency at a Conversion Ratio of 4.52020
- A Right-Half-Plane Zero-Free Buck-Boost DC-DC Converter with 97.46% High Efficiency and Low Output Voltage Ripple2019