Use of Artificial Neural Network for Prediction of Mechanical Properties of α-Al2O3 Particulate-reinforced Al–Si10Mg Alloy Composites Prepared by using Stir Casting Process
- 1 May 2006
- journal article
- research article
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 40 (9) , 779-796
Abstract
In this article, the tensile strength, hardening behavior, and density properties of different α-Al2O3 particle size (μm)-reinforced metal matrix composites (MMCs), produced by using stir casting process, are predicted by designing a backpropagation (BP) neural network that used gradient-descent learning algorithm. Artificial neural network (ANN) is an intelligent technique that can solve nonlinear problems by learning from the samples. Therefore, some experimental samples are prepared at first to train the ANN to provide (to estimate) tensile strength, hardening behavior, and density properties of the MMCs produced for any given α-Al2O3 particle size (μm). The most important point is that after the ANN has been trained using some experimental samples, it gives approximately correct outputs for some of the experimental inputs that have not been used in the training. First, to prepare the training and test (checking) set of the network, some results are experimentally obtained and recorded in a file on a computer. In the experiments, α-Al2O3 particles are supplied commercially. α-Al2O3 ceramic powder of a varying particle size of 10 vol% is prepared, and then this ceramic powder with different α-Al2O3 particle sizes is added to Al–Si10Mg alloy in melt condition by stir casting process. The effect of reinforced particle size on the tensile strength, hardness resistance, and density properties of α-Al2O3-reinforced MMCs have been investigated. Mechanical tests reveal that tensile strength and hardness resistance of the α-Al2O3 ceramic powder composites decrease with increasing reinforced α-Al2O3 particle size. Then, neural network is trained using the prepared training set, also known as the learning set. In the preparation of the ANN training module, the aim of the use of the model is to predict the tensile strength, hardening behavior, and density properties for any given α-Al2O3 particle size by using some experimental results. Different α-Al2O3 particle sizes (μm) are used as the input, and tensile strength, hardening behavior, and density properties are used as outputs in the neural network training module. The tensile strength, hardening behavior, and density properties of the produced MMCs are estimated for different α-Al2O3 particle sizes using neural network efficiently instead of time-consuming experimental processes. At the end of the training process, the test data are used to check the system accuracy. Simulation results confirm the feasibility of this approach and show a good agreement with experimental results for a wide range of MMCs produced.Keywords
This publication has 29 references indexed in Scilit:
- Mixture and pore volume fraction estimation in Al2O3/SiC ceramic cake using artificial neural networksMaterials & Design (1980-2015), 2005
- A study of neural network based inverse kinematics solution for a three-joint robotRobotics and Autonomous Systems, 2004
- Spinel effect on the mechanical properties of metal matrix composite AA6061/(Al2O3)pJournal of Materials Processing Technology, 2003
- Structure and properties of short alumina fibre reinforced AlSi18CuNi produced by stir castingMaterials Letters, 2002
- Dynamic mechanical properties of PTFE based short carbon fibre reinforced composites: experiment and artificial neural network predictionComposites Science and Technology, 2002
- Designing expert system with artificial neural networks for in situ toughened Si3N4Materials & Design (1980-2015), 2002
- Estimation of the amount of retained austenite in austempered ductile irons using neural networksMaterials Science and Engineering: A, 2001
- Prediction of ductile cast iron quality by artificial neural networksJournal of Materials Processing Technology, 2001
- Neural network applications in determining the fatigue crack opening loadInternational Journal of Fatigue, 1998
- The wetting of solids by molten metals and its relation to the preparation of metal-matrix composites compositesJournal of Materials Science, 1987