Femur Mechanical Properties in the F2 Progeny of an NZB/B1NJ × RF/J Cross Are Regulated Predominantly by Genetic Loci That Regulate Bone Geometry
Open Access
- 1 August 2006
- journal article
- research article
- Published by Oxford University Press (OUP) in Journal of Bone and Mineral Research
- Vol. 21 (8) , 1256-1266
Abstract
Genetic analysis of an NZB/B1NJ × RF/J cross has identified QTLs for femur mechanical, geometric, and densitometric phenotypes. Most mechanical QTLs were associated with geometric QTLs, strongly suggesting common genetic regulation. Introduction: Previous studies have shown that bone architecture and BMD are important factors affecting bone strength, and both are genetically regulated. We conducted genetic analyses for loci regulating femur mechanical properties, geometric properties, and BMD in a cohort of F2 mice derived from intercross matings of (NZB/B1NJ × RF/J)F1 parents. Materials and Methods: Femurs were isolated from 662 10-week-old females. Mechanical properties were determined for a femur from each animal by three-point bending. Geometric properties and volumetric BMD (vBMD) were determined by pQCT. Genotype data were obtained by PCR assays for polymorphic markers carried in the genomic DNA of each mouse. Genome-wide scans were carried out for co-segregation of genetic marker data with values from 23 different phenotypes. Quantitative trait loci (QTLs) were identified for mechanical, geometric, and mineral density phenotypes. Results: QTLs for many phenotypes were significantly refined by covariate analyses using body weight and femur length. Major QTLs for mechanical and geometric phenotypes were found on chromosomes 5, 7, 9, 11, and 12. Nine chromosomal locations were identified with mechanical QTLs and 17 locations with one or more geometric QTLs. The significance of five mechanical and nine geometric QTLs was affected by the inclusion of covariates. These changes included both decreases and increases in significance. The QTLs on chromosomes 5 and 12 were decreased by inclusion of the covariates in the analysis, but QTLs on 7 and 11 were unaffected. Mechanical QTLs were almost always associated with geometric QTLs and less commonly (two of six) with vBMD QTLs. Conclusions: Genetic regulation of mechanical properties in the F2 mice of this NZB/B1NJ × RF/J cross seems to be caused by genes regulating femur geometry.Keywords
This publication has 27 references indexed in Scilit:
- Adjusting Data to Body Size: A Comparison of Methods as Applied to Quantitative Trait Loci Analysis of Musculoskeletal PhenotypesJournal of Bone and Mineral Research, 2005
- Quantitative Trait Loci Analysis of Structural and Material Skeletal Phenotypes in C57BL/6J and DBA/2 Second-Generation and Recombinant Inbred MiceJournal of Bone and Mineral Research, 2005
- Genetic Effects for Femoral Biomechanics, Structure, and Density in C57BL/6J and C3H/HeJ Inbred Mouse StrainsJournal of Bone and Mineral Research, 2003
- Genetic Dissection of Femur Breaking Strength in a Large Population (MRL/MpJ×SJL/J) of F2 Mice: Single QTL Effects, Epistasis, and PleiotropyGenomics, 2002
- Chromosomal regions harboring genes for the work to femur failure in miceFunctional & Integrative Genomics, 2002
- Quantitative Trait Loci for Femoral and Lumbar Vertebral Bone Mineral Density in C57BL/6J and C3H/HeJ Inbred Strains of MiceJournal of Bone and Mineral Research, 2001
- Genetic loci influencing natural variations in femoral bone morphometry in miceJournal of Orthopaedic Research, 2001
- Breaking Down Bone Strength: A Perspective on the Future of Skeletal GeneticsJournal of Bone and Mineral Research, 2001
- A comprehensive genetic map of the mouse genomeNature, 1996
- Hierarchical Grouping to Optimize an Objective FunctionJournal of the American Statistical Association, 1963