Optimizing Low-Cost Gas Analysis with a 3D Printed Column and MiCS-6814 Sensor for Volatile Compound Detection
Authors:
- Nela SkowronkovaNSNela Skowronkova
- Martin AdamekMAMartin Adamek
- Magdalena ZvonkovaMZMagdalena Zvonkova
- Jiri MatyasJMJiri Matyas
- Anna AdamkovaAAAnna Adamkova
- Stepan DlabajaSDStepan Dlabaja
- Martin BuranMBMartin Buran
- Veronika SevcikovaVSVeronika Sevcikova
- Jiri MlcekJMJiri Mlcek
- Zdenek VolekZVZdenek Volek
- Martina CernekovaMCMartina Cernekova
Open Access
Abstract
This paper explores an application of 3D printing technology on the food industry. Since its inception in the 1980s, 3D printing has experienced a huge rise in popularity. This study uses cost-effective, flexible, and sustainable components that enable specific features of certain gas chromatography. This study aims to optimize the process of gas detection using a 3D printed separation column and the MiCS-6814 sensor. The principle of the entire device is based on the idea of utilizing a simple capillary chromatographic column manufactured by 3D printing for the separation of samples into components prior to their measurement using inexpensive chemiresistive sensors. An optimization of a system with a 3D printed PLA block containing a capillary, a mixing chamber, and a measuring chamber with a MiCS-6814 sensor was performed. The optimization distributed the sensor output signal in the time domain so that it was possible to distinguish the peak for the two most common alcohols, ethanol and methanol. The paper further describes some optimization types and their possibilities.Keywords
Funding Information
- Internal Grant Agency of Tomas Bata University in Zlin (IGA/FT/2024/006, RVO/CEBIA/2024/001, FEKT-S-23-8162, RP/CPS/2024-28/005, MZE-RO0723)
- Brno University of Technology project in Brno (IGA/FT/2024/006, RVO/CEBIA/2024/001, FEKT-S-23-8162, RP/CPS/2024-28/005, MZE-RO0723)
- Ministry of Education, Youth and Sports of the Czech Republic—DKRVO (IGA/FT/2024/006, RVO/CEBIA/2024/001, FEKT-S-23-8162, RP/CPS/2024-28/005, MZE-RO0723)
- Ministerstvo Zemědělství (IGA/FT/2024/006, RVO/CEBIA/2024/001, FEKT-S-23-8162, RP/CPS/2024-28/005, MZE-RO0723)
This publication has 23 references indexed in Scilit:
- A microchip gas chromatography column assembly with a 3D metal printing micro column oven and a flexible stainless-steel columnJournal of Chromatography A, 2024
- An open source 3D printed autosampler for capillary electrophoresisAnalytica Chimica Acta, 2023
- 3D-printed flexible sensors for food monitoringChemical Engineering Journal, 2023
- Differentiable detection of ethanol/methanol in biological fluids using prompt graphene-based electrochemical nanosensor coupled with catalytic complex of nickel oxide/8-hydroxyquinolineAnalytica Chimica Acta, 2022
- 3D-printed ordered bed structures for chromatographic purification of enveloped and non-enveloped viral particlesSeparation and Purification Technology, 2021
- A Review of 3D Printing Technologies for Soft Polymer MaterialsAdvanced Functional Materials, 2020
- 3D-Printed Stationary Phases with Ordered Morphology: State of the Art and Future Development in Liquid ChromatographyChromatographia, 2018
- Fundamentals and applications of 3D printing for novel materialsApplied Materials Today, 2017
- Materials for 3D printing in medicine2017
- Electronic nose based on partition column integrated with gas sensor for fruit identification and classificationComputers and Electronics in Agriculture, 2016