In Vitro Evaluation of Translucency and Color Stability of CAD/CAM Polymer‐Infiltrated Ceramic Materials after Accelerated Aging
- 19 August 2020
- journal article
- research article
- Published by Wiley in Journal of Prosthodontics
- Vol. 30 (4) , 318-328
Abstract
Purpose: To investigate and compare the translucency and color stability of a newly introduced polymer‐infiltrated ceramic network (PICN) material (Crystal Ultra) to those of clinically well‐established restorative materials.Materials and Methods: A total of 80 specimens measuring (12 × 14 × 1 mm ± 0.05 mm) were prepared from five CAD/CAM (IPS e.max (IPS), Lava Ultimate (LU), Cerasmart (CS), Vita Enamic (VE), Crystal Ultra (CU)) high translucency (HT) blocks in A2 or equivalent shades. Specimens were randomly allocated into two groups (A and B) (n = 8), and were subjected to 5,000 thermal‐cycles (TC). This was followed by one‐week immersion of group A specimens in coffee (staining) solution and group B specimens in distilled water. Following immersion, the specimens from both groups were further subjected to 5,000 TC. A spectrophotometer was used to measure the translucency parameter (TP) and color change (ΔE00) of the samples using CIELAB color coordinates at baseline, after 5,000 TC, following immersion, and after further 5,000 TC. Color stability was evaluated using the CIEDE2000 formula. Data were analyzed by non‐parametric tests (α = 0.05).Results: The TP values of the CAD/CAM materials ranged from 18.0‐22.0. Following the initial TC, the changes in TP values were significant for VE (p = 0.012). Coffee immersion and further TC significantly impacted the TP values of PICN (VE and CU) materials compared to glass‐ ceramics (IPS), and resin nanoceramic (CS and LU) materials (p = 0.012). The comparison between CAD/CAM materials at different intervals showed a significant difference in the TP values (p < 0.01). The materials showed perceptible color changes following the initial TC except for PICN materials which demonstrated acceptable color changes. The major color difference was noticed for the resin nanoceramic specimens immersed in coffee; LU and CS showed higher color changes (ΔE00 = 2.45 and 2.09, respectively) than VE and CU (ΔE00 < 1.8).Conclusions: The translucency of the newly introduced Crystal Ultra PICN material was low compared to the resin nanoceramics and lithium disilicate glass‐ceramic. The Crystal Ultra material exhibited better color stability compared to resin nanoceramics, but higher color change when compared with Vita Enamic PICN and lithium disilicate glass‐ceramic CAD/CAM materials.Keywords
This publication has 63 references indexed in Scilit:
- The effects of finishing and polishing techniques on surface roughness and color stability of nanocompositesJournal of Dentistry, 2012
- Ceramic materials in dentistry: historical evolution and current practiceAustralian Dental Journal, 2011
- Surface roughness and morphology of three nanocomposites after two different polishing treatments by a multitechnique approachDental Materials, 2010
- Optical influence of the type of illuminant, substrates and thickness of ceramic materialsDental Materials, 2009
- Measurement of translucency of tooth enamel and dentinActa Odontologica Scandinavica, 2009
- Translucency and biaxial flexural strength of four ceramic core materialsDental Materials, 2008
- Characterization of glass-infiltrated alumina-based ceramicsDental Materials, 2008
- Hygroscopic and hydrolytic effects in dental polymer networksDental Materials, 2006
- The CIEDE2000 color-difference formula: Implementation notes, supplementary test data, and mathematical observationsColor Research & Application, 2004
- Strength and fracture toughness of aluminum/alumina composites with interpenetrating networksMaterials Science and Engineering: A, 1995