The Influence of Pt Loading, Support and Nafion Content on the Performance of Direct Methanol Fuel Cells: Examined on the Example of the Cathode
Authors:
- 1 April 2011
- journal article
- research article
- Published by Wiley in Fuel Cells
- Vol. 11 (2) , 286-300
Abstract
Nano‐sized Pt colloids were prepared using the polyol method and supported on Ketjen black EC 600J (KB), Vulcan XC‐72 (VC) and high surface area graphite 300 (HG). The effects of the Nafion ionomer content, and the Pt loading of the cathode catalyst layer as well as the Pt loading on the support on the performance of direct methanol fuel cells (DMFCs), were studied. The membrane electrode assemblies (MEAs) were analysed using current–voltage curves, cyclic voltammetry, electrochemical impedance spectroscopy (EIS) and adsorbed CO stripping voltammetry. Optimum Nafion to carbon (N/C) ratios (N/C being defined as the weight ratio of the Nafion ionomer to the carbon) were determined. The optimum N/C ratios were found to depend on the support as follows, 1.4, 0.7 and 0.5 for Pt/KB, Pt/VC and Pt/HG, respectively and to be independent of the Pt/C loading range of 20–80 wt% tested in this work. The highest DMFC performances, as well as the highest electrochemical active surface areas, and improved gas diffusivities, were achieved using these ratios. For the catalysts prepared in this work, the average Pt crystallite size was found to decrease with increasing surface area of the support for a particular Pt loading. MEAs made using KB as support and the optimal N/C ratio of 1.4 showed the best performances, i.e. higher than the VC and HG supports for any N/C ratio. The highest DMFC performance was observed using 60 wt% Pt on KB cathode electrodes of 1 mg Pt cm–2loading and an N/C value of 1.4. For all three supports studied, the 60 wt% Pt on carbon loading resulted in the best DMFC performance. This may be linked to the Pt particle size and catalyst preparation method used in this work. In comparison to literature results, high DMFC performances were achieved using relatively ‘low' Pt and Ru loadings. For example, a maximum power density of >100 mW cm–2at 60 °C was observed using a 1 mg Pt cm–2cathode loading and a 2 mg PtRu cm–2anode loading.Keywords
This publication has 38 references indexed in Scilit:
- Performance degradation study of a direct methanol fuel cell by electrochemical impedance spectroscopyElectrochimica Acta, 2007
- Optimization of cathode catalyst layer for direct methanol fuel cells: Part II: Computational modeling and designElectrochimica Acta, 2006
- Determination of ionic resistance and optimal composition in the anodic catalyst layers of DMFC using AC impedanceInternational Journal of Hydrogen Energy, 2005
- Temperature dependence of the oxidation of carbon monoxide on carbon supported Pt, Ru, and PtRuElectrochemistry Communications, 2004
- Oxygen electroreduction on carbon-supported platinum catalysts. Particle-size effect on the tolerance to methanol competitionElectrochimica Acta, 2002
- Comparison of high surface Pt/C catalysts by cyclic voltammetryJournal of Power Sources, 2002
- Nafion content in the catalyst layer of polymer electrolyte fuel cells: effects on structure and performanceElectrochimica Acta, 2001
- Influence of Ionomer Content in Catalyst Layers on Direct Methanol Fuel Cell PerformanceJournal of the Electrochemical Society, 1999
- Mechanism and electrocatalysis in the direct methanol fuel cellCatalysis Today, 1997
- Thin-film catalyst layers for polymer electrolyte fuel cell electrodesJournal of Applied Electrochemistry, 1992